Seeed-Studio/Seeed_Arduino_CAN

Issues

• MCP2515 - Inverted frame sending

  #140 opened 2 years ago by andrejrcarvalho
  1

• CAN.getCanId() gets the ID of the TX MSG insted of the RX MSG

  #149 opened a year ago by Damians99
  0

• Problem receiving high frequency can device

  #152 opened 5 months ago by Zoylamb
  0

• Filters and masks do not seem to work properly

  #147 opened a year ago by reldneb
  1

• CAN extended (19 bit) frame cannot be detected by a receiver

  #142 opened 2 years ago by markwkiehl
  1

• MCP2515 init Fail

  #148 opened a year ago by Obili69
  0

• Examples Do Not Compile

  #138 opened 2 years ago by devindumont
  5

• I have a problem with the synchronization of messages

  #141 opened 2 years ago by JEFFERSON-HUERA
  1

• Can receive returns empty bytes, Can send doesnt send.

  #145 opened a year ago by illegal-instruction-co
  0

• Can not read message .. (extendet)

  #143 opened 2 years ago by aortner
  0

• Can BUS Shield init fail

  #82 opened 4 years ago by mat-lol-mat
  9

• no matching function for call to 'mcp2515_can::sendMsgBuf(int, int, int, unsigned char [8])'

  #137 opened 2 years ago by IAmOrion
  3

• MCP2515 doesnt init

  #130 opened 3 years ago by zigagazaziga
  1

• Problem with CAN BUS Receive Data

  #135 opened 3 years ago by Shoihya
  4

• PlatformIO out-of-date

  #132 opened 3 years ago by stijnb1234
  2

• warning: left shift count >= width of type

  #129 opened 3 years ago by EliasKotlyar
  1

• OBDII_PIDs:108: error: 'taskCanRecv' was not declared in this scope

  #133 opened 3 years ago by taoloo897
  0

• padding bytes in mcp2518fd_TransmitChannelLoad method is written into wrong locations

  #128 opened 3 years ago by AntDeM
  1

• cannot declare variable 'CAN' to be of abstract type 'MCP_CAN'

  #106 opened 4 years ago by mjat2020
  3

• Can't send supported PID's for odb2

  #126 opened 3 years ago by jlaustill
  1

• Unable to Install Library

  #125 opened 3 years ago by AlanX2033
  1

• This code is showing compiling error with seeeduino wio terminal after adding all the libraries required. Can anyone help me? #include <Servo.h> Servo myservo; int pos = 0; void setup() { myservo.attach(D0); //Connect servo to Grove Digital Port } void loop() { for (pos = 0; pos <= 179; pos += 1) { // in steps of 1 degree myservo.write(pos); delay(15); } for (pos = 179; pos >= 0; pos -= 1) { myservo.write(pos); delay(15); } }

  #124 opened 3 years ago by Anmolbaral
  1

• Can receive normal CAN frames, but not extended ones (ext parameter set)

  #115 opened 4 years ago by dhopf
  2

• MCP2518FD Filters not working

  #116 opened 4 years ago by TyphoonSB
  2

• Signed int , 16 bit int & float in can bus

  #119 opened 4 years ago by sundar19
  2

• RTR and EXT

  #114 opened 4 years ago by fkaraokur
  2

• CAN Interrupt Read Faulty

  #113 opened 4 years ago by georgiboby
  2

• Overflow in mcp2515_read_canMsg()

  #109 opened 4 years ago by gudnimg
  3

• Extended ID with 0x0..

  #111 opened 4 years ago by sundar19
  7

• A question with CS pin

  #112 opened 4 years ago by sundar19
  2

• Is it posible to Tx and Rx more than 8 bytes in one packet/frame

  #110 opened 4 years ago by Wodie
  1

• Arduino DUE

  #105 opened 4 years ago by zentT
  9

• Add the Seeed MCP2518FD module

  #102 opened 4 years ago by Pillar1989
  0

• CAN_83K3BPS for 8MHz not defined

  #79 opened 4 years ago by dartrax
  2

• at command?

  #80 opened 4 years ago by iuliancret
  2

• CAN_83K3BPS vs CAN_83KBPS (keywords.txt)

  #78 opened 4 years ago by dartrax
  2

• Canbus reading from a contactless clip

  #85 opened 4 years ago by vanbernaert
  1

• isRemoteRequest() issue

  #89 opened 4 years ago by vage24
  2

• CAN node as transciever

  #91 opened 4 years ago by poojitha-sai
  1

• Clock parameter missing in CAN.begin() in all of the examples

  #93 opened 4 years ago by greghol
  1

• Data transfer size (unsigned char buf[8]) 0

  #94 opened 4 years ago by Gbouna
  2

• Send Timeout in send function at low rates modes

  #95 opened 4 years ago by jmoyola
  2

• CanOpen

  #96 opened 4 years ago by florentheman
  2

• Read data from can-utils from can bus shield

  #97 opened 4 years ago by sourabhmisal
  1

• When in interrupt mode, the data coming can't be too fast, must >20ms, or else you can use check mode

  #98 opened 4 years ago by zentT
  4

• Filtering working only when Arduino nano is supplied with USB

  #99 opened 4 years ago by zentT
  2

• Debugging not working

  #100 opened 4 years ago by FabioBrondo
  1

• SPI_BEGIN() and SPI_END() Missing in mcp2515_read_canMsg

  #103 opened 4 years ago by zwells
  1

• Library Serial CAN_BUS errors

  #90 opened 5 years ago by PSCDPS
  1

• Cannot send messages longer than LEN=8

  #87 opened 5 years ago by mnd31
  2