Seeed RTL87XX AT firmware

Introduction

This RTL87XX AT firmware export a AT command interface through hardware SPI/UART port to MCU.
But current only works for RTL8720DN/RTL8720DM.

With those AT commands, the MCU could scan/connect WiFi APs, connect Internet/Intranet through the APs, or act as a TCP server (Web Server, Telnet Server, etc).

How to compile on Ubuntu Bionic

Clone this repo

    cd; git clone -b AT https://github.com/Seeed-Studio/seeed-ambd-sdk.git

Prepare gcc compiler

    cd seeed-ambd-sdk
    GCC_URL="http://files.seeedstudio.com/arduino/tools/arm-none-eabi/asdk-6.4.1-linux-newlib-build-2773-i686.tar.bz2"
    GCC_TOOL="project/realtek_amebaD_va0_example/GCC-RELEASE/project_hp/toolchain/asdk/$(basename $GCC_URL)"
    curl -fsSL $GCC_URL -o $GCC_TOOL

    # This gcc is x86 version, for X86_64 machine, install package libc6-i386
    sudo apt update
    sudo apt install libc6-i386

Start compiling

    make -C project/realtek_amebaD_va0_example/GCC-RELEASE/project_lp
    make -C project/realtek_amebaD_va0_example/GCC-RELEASE/project_hp CONFIG_WIFI_COUNTRY=RTW_COUNTRY_US CONFIG_WIFI_CHANNEL_PLAN=0x25

Country	CONFIG_WIFI_COUNTRY	CONFIG_WIFI_CHANNEL_PLAN
United States	RTW_COUNTRY_US	0x25
Japan	RTW_COUNTRY_JP	0x27

Check images compiled
Three binary files (km0_boot_all.bin, km4_boot_all.bin, km0_km4_image2.bin) must be exist if compiling successful.

    ls -l project/realtek_amebaD_va0_example/GCC-RELEASE/project_lp/asdk/image/km0_boot_all.bin
    ls -l project/realtek_amebaD_va0_example/GCC-RELEASE/project_hp/asdk/image/km4_boot_all.bin
    ls -l project/realtek_amebaD_va0_example/GCC-RELEASE/project_hp/asdk/image/km0_km4_image2.bin

How to burn images to RTL87XX chip

Refer to Wio-Terminal-Network-Overview to update to Wio Terminal.
Or Step 'Updating the Firmware' in above page to update to other RTL8720D device.

AT command list

WiFi/TCP Command	Format	Argument/Comment	Response
AT	AT	a dummy command only, could used to get OK response	OK
ATE	ATE0/ATE1	ATE0 disable command echo ATE1 enable command echo unimplement	OK
AT+GMR	AT+GMR	Query firmware version	OK
AT+GPIO	Query: AT+GPIO=R,<port-pin>[,0[,pull-set]] Set: AT+GPIO=W,<port-pin>,<value>[,pull-set]	Query or set GPIO level <port-pin>: PA25 if port is A, pin is 25 <value>: could be 0(low) or 1(high)	OK
AT+RST	AT+RST	Reboot the RTL87XX device	OK
AT+CWMODE	AT+CWMODE	Query or set Wireless mode	OK
AT+CWDHCP	AT+CWDHCP	Query or set DHCP mode	OK
AT+CWLAP	AT+CWLAP	List all scaned AP(Access Points)	OK
AT+CWQAP	AT+CWQAP	Quit connection to AP(Access Points)	OK
AT+CWJAP	AT+CWJAP	Get or set the connection to AP(Access Points)	OK
AT+CWSAP	AT+CWSAP	Get or set this AP(AP in RTL87XX)	OK
AT+CIPSTATUS	AT+CIPSTATUS	Query TCP/UDP connection status	OK
AT+CIPSTA	AT+CIPSTA	Query or set station IP address	OK
AT+CIPSTAMAC	AT+CIPSTAMAC	Query or set station MAC address	OK
AT+CIPAP	AT+CIPAP	Query or set IP address of this AP	OK
AT+CIPAPMAC	AT+CIPAPMAC	Query or set MAC address of this AP	OK
AT+CIPDOMAIN	AT+CIPDOMAIN	Query IP address of a domain name (DNS function)	OK
AT+CIPSTART	AT+CIPSTART	Create a TCP/UDP connection	OK
AT+CIPSEND	AT+CIPSEND	Send data to specific connection peer	OK
AT+CIPCLOSE	AT+CIPCLOSE	Close a specific connection	OK
AT+CIPDNS	AT+CIPDNS	Query or set the DNS address for RTL87XX	OK
AT+CIPSERVER	AT+CIPSERVER	Create a TCP/UDP Server to accept connection from Client	OK

BLE Command	Format	Argument/Comment	Response
ATBp	ATBp=<start-stop>	Start/stop BLE peripheral <start-stop> could be 0(stop) or 1(start)	OK
ATBc	ATBc	Start/stop BLE Central	OK
ATBS	ATBS	Scan BT	OK
ATBC	ATBC	Create a GATT connection(connect to remote device)	OK
ATBD	ATBD	Disconnect from remote device	OK
ATBK	ATBK	Reply GAP passkey, config authentication mode	OK
ATBG	ATBG	Get peripheral information	OK
ATBI	ATBI	Get information of connected device	OK
ATBY	ATBY	Reply GAP user confirm	OK
ATBU	ATBU	Update connection request	OK
ATBO	ATBO	Get/clear bond information	OK
ATBR	ATBR	GATT client read	OK
ATBW	ATBW	GATT client write	OK
ATBB	ATBB	Start/stop BT config	OK
ATBJ	ATBJ	Start/stop BT Beacon	OK
ATBb	ATBb	Start/stop BT Airsync config	OK
ATBf	ATBf	Start/stop BLE Scatternet	OK

This software AT command section is written by Seeed Studio
and is licensed under The MIT License. Check License.txt for more information.

Contributing to this software is warmly welcomed. You can do this basically by
forking, committing modifications and then pulling requests (follow the links above
for operating guide). Adding change log and your contact into file header is encouraged.
Thanks for your contribution.

Seeed Studio is an open hardware facilitation company based in Shenzhen, China.
Benefiting from local manufacture power and convenient global logistic system,
we integrate resources to serve new era of innovation. Seeed also works with
global distributors and partners to push open hardware movement.