Possible Enhancements
SukkoPera opened this issue · 11 comments
The first goal of this project is to produce a board equivalent to that of a standard A500+. This will allow to replace the board of a failing machine by salvaging components from it. It will also validate the schematics and general design.
Some deviations from the original design are expected (see #13), but basically it will be the same board.
After the first prototypes are confirmed working we can make changes to the board to bring the A500 design to the 21st century. This ticket shall collect ideas for upgrades.
-
2 MB Chip RAM onboard. This is simple, adding some RAM chips connected to /BRAS1 should be enough. It can either be done with the usual SOJ-40 chips or with a single 2 MB SOJ-42 chip. The latter would save quite a bit of board space.
-
Since the above would render the trapdoor slot useless, the trapdoor connector could be rewired so that it allows plugging some Slow RAM, as on earlier mainboard revisions. This can be discussed with PeteAU and the other guys who made the Open Design expansion on EAB.
EDIT: Someone mentioned the trapdoor connector could still be useful for an expansion board like the A314. But would it still work if we had 2 MB Chip RAM on the mainboard? -
8 MB Fast RAM onboard. This can be done using lvd's design or together with IDE and acceleration as detailed below.
-
IDE. Shall we replace Gary with Gayle or... (see below)?
-
Acceleration. We could get this and the above (and Fast RAM) with help from Mr Leary and his TerribleFires. Not sure it is easily doable on a 2-layer board though.
6. Use drive/power led for HD activity. See here. Done in V2.
7. Integrate a Kickstart Switcher. Done in ab97624.
8. Integrate a Drive Switcher. Done in c3e6573.
-
Integrate a Gotek Drive (Schematics here, firmware would be FlashFloppy of course).
-
Color composite output. Not sure we should do this onboard, as I would like to do it in OpenAmigaVideoHybrid through an AD724 chip, so that any A500 could get this nice addition, as well as a possible S-Video output.
-
Replace (or better integrate) the joystick/mouse ports with USB ports. This can be done with a single STM32F105 chip, just like HID2AMI, but we would need to write an GPL'd firmware for that first. Doable but a long job on its own.
-
Clock port. What could this be useful for? USB?
-
Integrate a PlipBox Ethernet card.
If we need to gain space on the board, we can replace the CPU and/or ROM with PLCC versions or use SOIP chips, but this would require quite a bit of rewiring.
Another idea could be making an ATX-format Amiga board, maybe with some Zorro II expansions slot as well.
7 and 8 are done.
I like points 3 and 4 together. It makes an A500 a good ClassicWB machine. Was even looking into combining these 2 into a single board with a shared CPLD. What broke me was the ide68k source written in ABEL :)
Integrating Gotek is also a good ideas, as you can wire all the OSD stuff on the motherboard itself.
Maybe provide slots for extra RAM and the replace trapdoor slot with something of higher density exposing the important pins? (INT, 68k BUS, some amiga ASIC pins) Then accelerators and other expansions can be done on >2 layer boards confined to the trapdoor. If you replace the RAMs with a single 2MB chip, it might free up space to route all these connections to the ex-trapdoor position.
I'm not going to do any new work on this (or any other, actually) project. If anyone wants to have a go at any of these points, feel free to do it.
Understood. Thanks for your work in this project. It might help a lot of people with dead A500+. I managed to revive mine with some wires, otherwise would already be sending you patches ;)
Why not put the option for a 68010 processor (I think is pretty the same maybe only an higher clock rate) ?
I remember some of my high-school friends using it ....
I don't think the 68010 requires any particular hardware support, it should be a drop-in replacement for the 68000. Anyone who builds this can already use it straight away.
Yep it should be pin-2-pin compatibile that's sure but if I remember well my friends used to clock it much higher than ordinary A500 68k (7MHz?) they where probably using a clock doubler since 68010 was already running up to 16MHz.
Well, I have no idea of how to do that. If you want to contribute, you are welcome to join the project.
I would like to do a 2MB chipmem for this board, i have lots of the 2MB SOJ 42 chips left over from my 8MB fastmem/IDE project, does anyone have a schematic on how to plumb this in, so i can give it a shot. Thanx
I have a piggyback board that I used for some experiments. It has a switch to select 1 or 2 MB of chip RAM with a single SOJ-42 chip. Both configurations seem to work great, but for some reason, when it's set to 1 MB, plugging a trapdoor expansion will result in odd video issues.
Once that is debugged, it would be very nice to integrate this feature into Raemixx.
I also have 10 done, and 11 wuld be around 95% done (on a separate board, to be integrated).
There's also a good design to be integrated for 3 + 4.
Too bad I got sick of it all.