ModbusSlave

ModbusSlave library for Arduino

This modbus slave library uses callbacks to handle modbus requests. Handler functions are called on modbus request, and the users can implement them in their sketch.

ModbusSlave is fun and easy to use

slave.cbVector[CB_READ_INPUT_REGISTERS] = ReadAnalogIn;

Implement it:

void ReadAnalogIn(uint8_t fc, uint16_t address, uint16_t length) {
    for (int i = 0; i < length; i++)
        slave.writeRegisterToBuffer(i, analogRead(address + i));
}

And thats it, your sketch is modbus enabled. (see the full examples for more detail)

Install
Competabilty
Callback vector - Slots - Handler function - Function codes - Reading and writing to the request buffer
Examples - handle "Force Single Coil" as arduino digitalWrite - handle "Read Input Registers" as arduino analogRead

Install

Download the zip package, and install it into your Arduino IDE. See the Arduino tutorial about installing 3rd party libraries: https://www.arduino.cc/en/Guide/Libraries#toc4

Competabilty

This class implements:

FC1 "Read Coil Status"
FC2 "Read Input Status"
FC3 "Read Holding Registers"
FC4 "Read Input Registers"
FC5 "Force Single Coil"
FC6 "Preset Single Register"
FC15 "Force Multiple Coils"
FC16 "Preset Multiple Registers"

Serial port

The default serial port is Serial, but any class that inhirets from Stream can be used. To set a different Serial class, explicitly set the Stream in the Modbus class constuctor.

Callback vector

Users register handler functions into the callback vector.

Slots

The callback vector has 4 slots for request handlers:

slave.cbVector[CB_READ_COILS] - called on FC1
slave.cbVector[CB_READ_DISCRETE_INPUTS] - called on FC2
slave.cbVector[CB_READ_HOLDING_REGISTERS] - called on FC3
slave.cbVector[CB_READ_INPUT_REGISTERS] - called on FC4
slave.cbVector[CB_WRITE_COILS] - called on FC5 and FC15
slave.cbVector[CB_WRITE_HOLDING_REGISTERS] - called on FC6 and FC16

Handler function

Handler functions must return unit8_t and take:

uint8_t fc - request function code
uint16_t address - first register / first coil address
uint16_t length - length of data

Return codes:

STATUS_OK = 0,
STATUS_ILLEGAL_FUNCTION,
STATUS_ILLEGAL_DATA_ADDRESS,
STATUS_ILLEGAL_DATA_VALUE,
STATUS_SLAVE_DEVICE_FAILURE,
STATUS_ACKNOWLEDGE,
STATUS_SLAVE_DEVICE_BUSY,
STATUS_NEGATIVE_ACKNOWLEDGE,
STATUS_MEMORY_PARITY_ERROR,
STATUS_GATEWAY_PATH_UNAVAILABLE,
STATUS_GATEWAY_TARGET_DEVICE_FAILED_TO_RESPOND

Function codes

FC_READ_COILS = 1
FC_READ_DISCRETE_INPUT = 2
FC_READ_REGISTERS = 3
FC_READ_INPUT_REGISTERS = 4
FC_WRITE_COIL = 5
FC_WRITE_REGISTER = 6
FC_WRITE_MULTIPLE_COILS = 15
FC_WRITE_MULTIPLE_REGISTERS = 16

Reading and writing to the request / response buffer

int readCoilFromBuffer(int offset) : read one coil value from the request buffer.
uint16_t readRegisterFromBuffer(int offset) : read one register value from the request buffer.
void writeCoilToBuffer(int offset, int state) : write one coil state into the answer buffer.
void writeRegisterToBuffer(int offset, uint16_t value) : write one register value into the answer buffer.

Examples

handle "Force Single Coil" as arduino digitalWrite

#include <ModbusSlave.h>

// implicitly set stream to use the Serial serialport
Modbus slave(1, 8); // [stream = Serial,] slave id = 1, rs485 control-pin = 8

void setup() {
    // register one handler functions
    // if a callback handler is not assigned to a modbus command 
    // the default handler is called. 
    // default handlers return a valid but empty replay.
    slave.cbVector[CB_WRITE_COILS] = writeDigitlOut;
    
    // start slave at baud 9600 on Serial
    Serial.begin( 9600 ); // baud = 9600
    slave.begin( 9600 );
}

void loop() {
    // listen for modbus commands con serial port
    slave.poll();
}

// Handel Force Single Coil (FC=05)
uint8_t writeDigitlOut(uint8_t fc, uint16_t address, uint16_t length) {
    if (slave.readCoilFromBuffer(0) == HIGH) {
        digitalWrite(address, HIGH);
    } else {
        digitalWrite(address, LOW);
    }
    return STATUS_OK;
}

handle "Read Input Registers" as arduino analogRead

#include <ModbusSlave.h>

// explicitly set stream to use the Serial serialport
Modbus slave(Serial, 1, 8); // stream = Serial, slave id = 1, rs485 control-pin = 8

void setup() {
    // register handler functions
    slave.cbVector[CB_READ_INPUT_REGISTERS] = ReadAnalogIn;
    
    // start slave at baud 9600 on Serial
    Serial.begin( 9600 ); // baud = 9600
    slave.begin( 9600 );
}

void loop() {
    // listen for modbus commands con serial port
    slave.poll();
}

// Handel Read Input Registers (FC=04)
uint8_t ReadAnalogIn(uint8_t fc, uint16_t address, uint16_t length) {
    // write registers into the answer buffer
    for (int i = 0; i < length; i++) {
      slave.writeRegisterToBuffer(i, analogRead(address + i));
    }
    return STATUS_OK;
}

TobiasSchaffner/ArduinoModbusSlave