TomNisbet/TommyPROM

Issues

• Shift registers

  #2 opened 6 years ago by coolname1
  16

• TommyPROM32 : Ok to replace SW1 and SW2 with jumpers ?

  #72 opened 9 months ago by ABelliqueux
  2

• Cannot burn image

  #61 opened a year ago by ian-rose
  3

• can it run in arduino mega? because mega has alot of gpio, no need other ic.

  #23 opened 4 years ago by youxiaojie
  6

• Hardware Verify Not Working?

  #54 opened 10 months ago by OrlandoBlyat
  3

• 27C256

  #53 opened 10 months ago by ElectroBoy404NotFound
  12

• please add support for AT29C020 device (Atmel TSOP32 Flash)

  #52 opened 10 months ago by invictus737
  9

• Problem transferring files from a Mac

  #46 opened 10 months ago by srayner
  7

• Programming a 27C040 - will this work

  #37 opened 10 months ago by danriches
  4

• Arduino Nano Every ATMega4809

  #59 opened 10 months ago by bogrol2003
  1

• CSI CAT28C16AP working?

  #66 opened a year ago by jscrane
  5

• Alternative Hardware Idea

  #63 opened a year ago by Mike-K8LH
  0

• Problems writing to 28C256 through Xmodem

  #56 opened 2 years ago by hadron13
  3

• 5.5 volts , USB volts , VCC volts

  #36 opened 2 years ago by haroldmoore
  4

• 28C64 Not Working

  #38 opened 2 years ago by ElectroBoy404NotFound
  6

• Using TommyPROM as basis for slightly odd flash rom board

  #39 opened 2 years ago by AJRubenstein
  1

• Can sketch size be reduced to run on Nano 168 ?

  #40 opened 2 years ago by srayner
  1

• W27C512

  #45 opened 2 years ago by Henkvd72
  2

• 74HC595 Shift Registers always on

  #24 opened 4 years ago by Tohaker
  1

• 595 shift registers and code

  #21 opened 4 years ago by halak77
  4

• (Minor) - Confirmation that device successfully passed the multi-pass check.

  #16 opened 4 years ago by NonDualChris
  2

• XModem checksum failing with TeraTerm

  #20 opened 4 years ago by TomNisbet
  4

• Change XModem to use checksum instead of CRC16

  #19 opened 4 years ago by TomNisbet
  0

• 74LS595 variant not working

  #18 opened 4 years ago by TomNisbet
  1

• Writes failing on some Atmel 28C256 chips

  #17 opened 4 years ago by TomNisbet
  1

• Can't unlock AT28C256

  #6 opened 5 years ago by Lx32
  15

• HardwareVerify - Minor documentation changes required to clarify use

  #13 opened 5 years ago by NigelTwo
  4

• TommyPROM v2.2 '595 Shift Register code has introduced a bug

  #15 opened 5 years ago by NigelTwo
  3

• Read and Xmodem-CRC save command failing with minicom (and suggested fix)

  #14 opened 5 years ago by NigelTwo
  3

• Errors with AT28C256

  #10 opened 5 years ago by squelch41
  3

• Suggested enhancement

  #12 opened 5 years ago by aemiller51
  2

• Missing character in dump command

  #11 opened 5 years ago by TomNisbet
  0

• Schematic error

  #9 opened 5 years ago by squelch41
  2

• TommyProm writing same data to all addresses on Zap test

  #5 opened 5 years ago by 8BitMark
  9

• Menu appears in Arduino serial term but not in TeraTerm

  #7 opened 5 years ago by 8BitMark
  2

• Terminal line ending should support CR or LF

  #8 opened 5 years ago by TomNisbet
  0

• Trying to get TommyPROM working?

  #3 opened 6 years ago by JohnDavidGay
  14