Xinyuan-LilyGO/LilyGo-LoRa-Series

Issues

• Programming on LILYGO T-Beam Supreme module using Arduino IDE

  #205 opened 2 days ago by Tanay7
  6

• T-Beam_V1.2 Schematic Circuit

  #206 opened 7 days ago by ajg555
  2

• LoRa32 V2.1_1.6

  #180 opened 3 months ago by pbh8075
  4

• Can't make LoRa32 T3S3 even boot on Platformio

  #204 opened 22 days ago by richonguzman
  2

• Unused pin for additional sensor

  #203 opened 24 days ago by pongohost
  3

• TTGO V2.1 Custom pogram

  #200 opened 23 days ago by Edgineer10
  5

• DCDC1 & DCDC3 on T-Beam v1.2

  #190 opened 25 days ago by moshe-braner
  13

• Compile an example code for T-Beam v1.2

  #201 opened 2 months ago by sirfonzie
  11

• How to minimize energy consumption in sleep mode for a periodic on/off cycle?

  #198 opened a month ago by martin229101
  3

• TTGO Lora32-OLED SX1276_Receive_Interrupt.ino compile error

  #197 opened a month ago by KenSamson
  6

• Can the T3-S3 be used at 923MHz?

  #196 opened a month ago by gilchi
  5

• GPS Mode for T-Beams module: Continuous?

  #202 opened a month ago by richonguzman
  2

• WiFi AP "password incorrect" in one T3S3 board

  #171 opened 2 months ago by moshe-braner
  13

• Regarding the LoRa Chirp Issue of T3-S3 SX1280 2.4G With PA.

  #193 opened 2 months ago by Wanghaoyu920
  3

• the new T3 S3 E-paper board

  #191 opened 2 months ago by moshe-braner
  4

• T3_S3_V1.2 schematics are missing

  #199 opened 3 months ago by flugplatz-berching
  1

• T3S3: Add support to Adruino-esp32

  #179 opened 3 months ago by joyel24
  8

• Ranging

  #189 opened 3 months ago by JockNines101
  3

• LoraSender issues while running the example code

  #186 opened 3 months ago by dewaste08
  5

• RSSI signal not good

  #187 opened 3 months ago by cmussoni
  4

• Updated pin layout image

  #188 opened 3 months ago by icepick3000
  3

• SD_MSC and board re-start

  #195 opened 3 months ago by TigoTas
  4

• T3S3 in hot temperature

  #192 opened 3 months ago by moshe-braner
  1

• Can't upload sketches to T3 S3

  #194 opened 3 months ago by TigoTas
  2

• Unable to Read Sensor Data via I2C on LilyGO LoRa32

  #182 opened 3 months ago by Mariiian09
  6

• T3S3 v1.2: No USB Power Output on USB OTG Host mode (Power via Battery JST only)

  #178 opened 3 months ago by joyel24
  8

• SD with LoRa fails

  #168 opened 3 months ago by mkarat99
  5

• RadioLib PingPong not working

  #173 opened 3 months ago by vitalmuffin
  7

• Device stops working and hot after usb plugged in

  #174 opened 3 months ago by fagci
  5

• How to connect to TTN

  #175 opened 3 months ago by mattsoftware
  3

• T3S3 LoRa Board - Stuck in Bootloader

  #172 opened 4 months ago by starlight-traveler
  7

• How to use MESHTASTIC with more personalised configuration?

  #167 opened 4 months ago by dms-rj
  3

• How can I insert distinct LoRa config for each channel desired?

  #169 opened 4 months ago by dms-rj
  3

• Does SX1262 have different sensitivity at different frequencies?

  #185 opened 4 months ago by XieyangSun
  1

• T3S3 USB flashing without the IDE

  #164 opened 4 months ago by moshe-braner
  4

• No examples of T3_V1.6.1 using display and SD card

  #162 opened 4 months ago by jorgie0
  3

• SoftRF Prime MK3 not receiving GPS Position / Satellite Connection

  #177 opened 5 months ago by LouisTrinczek
  9

• T3S3 - Board fails to start with PSRAM set to QSPI

  #184 opened 5 months ago by pksimeonov
  2

• schematics access errors

  #181 opened 5 months ago by tolson2000
  2

• T-Beam SupremeS3 Schematic: Connection of RTC_INT to PCF8563 pin#3 makes no sense, is it wrong?

  #183 opened 5 months ago by cyberman54
  2

• Endless boot/crash loop when in Repeater, Router, or Router+Client Mode

  #161 opened 5 months ago by Felix-Quehl
  2

• T3-S3 SX1262 will not boot with any powerbank

  #170 opened 5 months ago by madler
  6

• T3S3 v1.2: if "USB CDC on boot" enabled, cannot boot from USB power-only?

  #163 opened 5 months ago by moshe-braner
  3

• SMD component getting really hot during charging T3-S3 V1.2

  #159 opened 5 months ago by Vincent-NB
  3

• Trouble Receiving Signal with Lilygo LoRa32 433 v2.1 for Garage Door Opener

  #160 opened 5 months ago by potabash
  2

• Unable to select the respective board during flash procedure

  #176 opened 5 months ago by strobesactual
  3

• T-Beam V1.2 Mismatch Schematic to PCB - Header U12 Pin 1 5V is connected to USB VBUS0 instead of VSYS

  #157 opened 5 months ago by dj9pz
  5

• Inconsistent pinout TTGO LoRa T3-S3

  #158 opened 5 months ago by BadCactus634
  4

• NEO M8N disarmed

  #165 opened 6 months ago by dms-rj
  3

• T-Motion (version 2021) firmware update procedure not possible

  #166 opened 6 months ago by fraktal-sb
  2