/esp32_nat_router

A simple NAT Router for the ESP32

Primary LanguageC

ESP32 NAT Router

This is a firmware to use the ESP32 as WiFi NAT router. It can be used as

  • Simple range extender for an existing WiFi network
  • Setting up an additional WiFi network with different SSID/password for guests or IOT devices

It can achieve a bandwidth of more than 15mbps.

The code is based on the Console Component and the esp-idf-nat-example.

Performance

All tests used IPv4 and the TCP protocol.

Board Tools Optimization CPU Frequency Throughput Power
ESP32D0WDQ6 iperf3 0g 240MHz 16.0 MBits/s 1.6 W
ESP32D0WDQ6 iperf3 0s 240MHz 10.0 MBits/s 1.8 W
ESP32D0WDQ6 iperf3 0g 160MHz 15.2 MBits/s 1.4 W
ESP32D0WDQ6 iperf3 0s 160MHz 14.1 MBits/s 1.5 W

First Boot

After first boot the ESP32 NAT Router will offer a WiFi network with an open AP and the ssid "ESP32_NAT_Router". Configuration can either be done via a simple web interface or via the serial console.

Web Config Interface

The web interface allows for the configuration of all parameters. Connect you PC or smartphone to the WiFi SSID "ESP32_NAT_Router" and point your browser to "http://192.168.4.1". This page should appear:

First enter the appropriate values for the uplink WiFi network, the "STA Settings". Leave password blank for open networks. Click "Connect". The ESP32 reboots and will connect to your WiFi router.

Now you can reconnect and reload the page and change the "Soft AP Settings". Click "Set" and again the ESP32 reboots. Now it is ready for forwarding traffic over the newly configured Soft AP. Be aware that these changes also affect the config interface, i.e. to do further configuration, connect to the ESP32 through one of the newly configured WiFi networks.

If you want to enter a '+' in the web interface you have to use HTTP-style hex encoding like "Mine%2bYours". This will result in a string "Mine+Yours". With this hex encoding you can enter any byte value you like, except for 0 (for C-internal reasons).

It you want to disable the web interface (e.g. for security reasons), go to the CLI and enter:

nvs_namespace esp32_nat
nvs_set lock str -v 1

After restart, no webserver is started any more. You can only re-enable it with:

nvs_namespace esp32_nat
nvs_set lock str -v 0

If you made a mistake and have lost all contact with the ESP you can still use the serial console to reconfigure it. All parameter settings are stored in NVS (non volatile storage), which is not erased by simple re-flashing the binaries. If you want to wipe it out, use "esptool.py -p /dev/ttyUSB0 erase_flash".

Command Line Interface

For configuration you have to use a serial console (Putty or GtkTerm with 115200 bps). Use the "set_sta" and the "set_ap" command to configure the WiFi settings. Changes are stored persistently in NVS and are applied after next restart. Use "show" to display the current config.

Enter the help command get a full list of all available commands.

If you want to enter non-ASCII or special characters (incl. ' ') you can use HTTP-style hex encoding (e.g. "My%20AccessPoint" results in a string "My AccessPoint").

Flashing the prebuild Binaries

Install esptool, go to the project directory, and enter:

esptool.py --chip esp32 --port /dev/ttyUSB0 \
--baud 115200 --before default_reset --after hard_reset write_flash \
-z --flash_mode dio --flash_freq 40m --flash_size detect \
0x1000 build/bootloader/bootloader.bin \
0x10000 build/esp32_nat_router.bin \
0x8000 build/partitions_example.bin

As an alternative you might use Espressif's Flash Download Tools with the parameters given in the figure below (thanks to mahesh2000):

image

Building the Binaries

The following are the steps required to compile this project:

  1. Download and setup the ESP-IDF.

  2. In the project directory run make menuconfig (or idf.py menuconfig for cmake).

    1. *Component config -> LWIP > [x] Enable copy between Layer2 and Layer3 packets.
    2. *Component config -> LWIP > [x] Enable IP forwarding.
    3. *Component config -> LWIP > [x] Enable NAT (new/experimental).
  3. Build the project and flash it to the ESP32.

A detailed instruction on how to build, configure and flash a ESP-IDF project can also be found the official ESP-IDF guide.

DNS

By Default the DNS-Server which is offerd to clients connecting to the ESP32 AP is set to 8.8.8.8. Replace the value of the MY_DNS_IP_ADDR with your desired DNS-Server IP address (in hex) if you want to use a different one.

Troubleshooting

Line Endings

The line endings in the Console Example are configured to match particular serial monitors. Therefore, if the following log output appears, consider using a different serial monitor (e.g. Putty for Windows or GtkTerm on Linux) or modify the example's UART configuration.

This is an example of ESP-IDF console component.
Type 'help' to get the list of commands.
Use UP/DOWN arrows to navigate through command history.
Press TAB when typing command name to auto-complete.
Your terminal application does not support escape sequences.
Line editing and history features are disabled.
On Windows, try using Putty instead.
esp32>