aegean-odyssey/mpmd_marlin_1.1.x

Issues

• communication problem

  #103 opened 8 months ago by berberic2
  1

• error:Probing failed

  #102 opened a year ago by Beanman122
  0

• PID tune typo?

  #94 opened 3 years ago by BackwardEcho
  2

• Printer pauses midprint using octopi

  #96 opened 3 years ago by THE-BOW
  5

• FAN needs support

  #76 opened 3 years ago by BackwardEcho
  55

• Lower EXTRUDER_AUTO_FAN_SPEED

  #41 opened 4 years ago by PurpleHullPeas
  5

• E1"Heating" Error

  #64 opened 4 years ago by zapata7515
  54

• Max bed temperature.

  #91 opened 3 years ago by Weberowsky
  2

• Real Z location lost after M420 S1

  #90 opened 3 years ago by martini1992
  1

• Bizarre Behavior when Calibrating

  #86 opened 3 years ago by gordsellar
  2

• Corrupt display

  #63 opened 3 years ago by john-clark
  7

• Firmware Flashed Successfully, SD Card No Longer Reads

  #52 opened 3 years ago by TaylorDeeves
  14

• autolevel and bed thickness

  #53 opened 3 years ago by drji3m
  18

• Firmware will not flash from newer cards which the new firmware will read just fine

  #83 opened 3 years ago by nathanielstenzel
  3

• A hint on wifi file uploads

  #84 opened 3 years ago by nathanielstenzel
  4

• Pronterface Serial Exception

  #80 opened 3 years ago by aegean-odyssey
  11

• Help to compile new firmware

  #82 opened 3 years ago by Electromente
  1

• Version clarification

  #79 opened 3 years ago by BackwardEcho
  2

• Question about M92

  #78 opened 3 years ago by Electromente
  2

• Control FAN

  #77 opened 3 years ago by Electromente
  4

• Thermal Runaway after updating firmware

  #72 opened 4 years ago by wvanlue1
  2

• E1 Thermal Runaway

  #40 opened 4 years ago by BackwardEcho
  12

• effector collison with starting g-code

  #69 opened 4 years ago by skylersell
  1

• ROM overflow when compiling MPMD under ubuntu 20.04.1LTS

  #35 opened 4 years ago by mgouget
  6

• 2004LCD support

  #36 opened 4 years ago by mcexperts
  2

• Strange extruder results and unload/load limitations

  #34 opened 4 years ago by see3d
  4

• Successive G30 probes shift Z height

  #38 opened 4 years ago by mulcmu
  34

• G33 auto bed level adjustment for M665 R,L

  #25 opened 4 years ago by see3d
  6

• G29 probe pattern improvement

  #29 opened 4 years ago by see3d
  20

• G30, G29 probe method improvement request

  #30 opened 4 years ago by see3d
  4

• G29 P0 does not work as expected

  #54 opened 4 years ago by aegean-odyssey
  1

• Crash when trying the 25mm calibration gcode

  #47 opened 4 years ago by BackwardEcho
  12

• Z height

  #51 opened 4 years ago by skylersell
  2

• Improper boot without an SD card inserted

  #32 opened 4 years ago by BackwardEcho
  7

• Skipping custom gcode commands

  #33 opened 4 years ago by BackwardEcho
  10

• Hesitation/Reboot with USB plugged in but no software connection open

  #48 opened 4 years ago by mulcmu
  10

• Cannot calibrate, G33 "Error:Probing failed"

  #43 opened 4 years ago by e-lambert
  5

• Extruder Crashing into back of printer during AUTO_CALIBRATE.gcode

  #42 opened 4 years ago by Jozer99
  1

• Flashing red light

  #39 opened 4 years ago by skylersell
  3

• two Problems : 1.Printer freezes still at the end of a print 2. Calibration out of the bed...

  #37 opened 4 years ago by BjoernBjoernson
  24

• Bed temp never reached, stays 1.2-1.8 degrees C below target

  #31 opened 4 years ago by howels
  3

• Quick-Start Documentation Updates - PurpleHullPeas rev1

  #26 opened 4 years ago by PurpleHullPeas
  12

• Thermistor readouts are very noisy.

  #20 opened 4 years ago by see3d
  12

• Document G29 differences from upstream Marlin behaviour

  #27 opened 4 years ago by ToxicFrog
  8

• G30 single probe method?

  #23 opened 4 years ago by see3d
  38

• Printer reboots when attempting to start print with PCFan firmware

  #24 opened 4 years ago by Adam-Beaumont
  29

• Support for M205 B gcode

  #22 opened 4 years ago by see3d
  2

• Printer hangs after G29 error

  #28 opened 4 years ago by ToxicFrog
  1

• G29 Parabolic Post-Processing

  #21 opened 4 years ago by PurpleHullPeas
  3

• Hot end carriage colliding with rear bed retainer during levelling

  #19 opened 4 years ago by bakedpanda
  2