/r8152-Synology

Synology DSM driver for Realtek RTL8152/RTL8153/RTL8156 based adapters

Primary LanguageCGNU General Public License v2.0GPL-2.0

DSM driver for realtek RTL8152/RTL8153/RTL8156 based USB Ethernet adapters

This is an RTL8152/RTL8153/RTL8156(2.5Gbps or 1.0Gbps) driver package for Synology NASes.

You may also be interested in my other projects:

Supported NAS platform

  • DSM 7.x
  • apollolake based products
    • DS918+ (confirmed working)
    • DS620slim
    • DS1019+
    • DS718+
    • DS418play
    • DS218+

You can download drivers including other platforms from the release page and determine a proper driver for your model from knowledge base of Synology, but you might encounter some issues with unconfirmed platforms. If you are using such unconfirmed models, the Compatibility page may be helpful.

I very much appreciate it if you could report whether it works. If you have any problems, the Troubleshooting page may help.

NOTE: I recommend using front ports to connect devices because some users reported stability issues when they use rear ports.

Supported RTL8156(2.5Gbps) based devices

INFO: Products using RTL8156BG have dramatically lower power consumption(up to 64% decrease) and heat generation than those using RTL8156.

See the Compatibility page for the latest information.

  • If you have other products not listed and they do not work, please create an issue with the output of lsusb.
  • If you are using a product with a Type-C connector, you will need a connector or cable to convert it to Type-A.
    • For stable device operation, I recommend using a USB 3.2gen2 10Gbps compatible cable.
    • A 5Gbps cable is sufficient for this driver to work, but a 10Gbps capable cable can be expected to have higher transmission quality.

How to install

Preparation

Enable SSH and login your NAS.

Installation

  1. Go to "Package Center"
  2. Press "Manual Install"
  3. Choose a driver package downloaded from the release page.
  4. [DSM7] The installation will fail the first time. After that, run the following command from the SSH terminal:
    • sudo install -m 4755 -o root -D /var/packages/r8152/target/r8152/spk_su /opt/sbin/spk_su
  5. [DSM7] Retry installation.
    • You don't need the above DSM7-specific steps at the next time.
  6. Reboot your NAS.
    • This procedure is not usually necessary, but many have reported that a reboot was necessary, so please reboot just in case.

https://www.synology.com/en-us/knowledgebase/SRM/help/SRM/PkgManApp/install_buy

Warning: Do not use Safari for this operation.

How to configure

You can configure the IP addresses and MTU of the added NICs from the DSM UI in the same way as the built-in NICs.

Option: I recommend setting MTU to 9000 and SMB protocol version to v3 for better performance.

Performance test

Environment

  • DS918+ (USB-LAN2500R)
  • DSM 6.2
  • direct connection with PC (AQN-107: discontinued, but almost equivalent to ASUS XG-C100C)
  • native iperf3
    • using docker causes high CPU load

Result

Connecting to host 192.168.0.xxx, port 5201
[  4] local 192.168.0.xxx port 50366 connected to 192.168.0.xxx port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec   266 MBytes  2.23 Gbits/sec
[  4]   1.00-2.00   sec   274 MBytes  2.30 Gbits/sec
[  4]   2.00-3.00   sec   278 MBytes  2.33 Gbits/sec
[  4]   3.00-4.00   sec   278 MBytes  2.33 Gbits/sec
[  4]   4.00-5.00   sec   278 MBytes  2.33 Gbits/sec
[  4]   5.00-6.00   sec   278 MBytes  2.34 Gbits/sec
[  4]   6.00-7.00   sec   274 MBytes  2.30 Gbits/sec
[  4]   7.00-8.00   sec   267 MBytes  2.24 Gbits/sec
[  4]   8.00-9.00   sec   269 MBytes  2.26 Gbits/sec
[  4]   9.00-10.00  sec   271 MBytes  2.27 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.00  sec  2.67 GBytes  2.29 Gbits/sec                  sender
[  4]   0.00-10.00  sec  2.67 GBytes  2.29 Gbits/sec                  receiver

iperf Done.