/multi-master-kubernetes

Multi-master Kubernetes cluster on Exoscale

Primary LanguagePython

Multi-master Kubernetes

This Ansible playbook helps you setup a multi-master Kubernetes cluster on Exoscale.

Getting started

To run this playbook a working Docker installation and a basic understanding of containers and volumes is required. You also need a Exoscale account and the corresponding API key and secret.

You can get your key and secret here: https://portal.exoscale.ch/account/profile/api

Let's bootstrap a cluster.

# Run the container and mount a data volume for the cluster specific secrets
docker run -ti -v k8s_secrets:/secret exoscale/multi-master-kubernetes

# Set EXO_API_KEY and EXO_API_SECRET environment variables
export EXO_API_KEY=
export EXO_API_SECRET=

# Then run the cluster-bootstrap playbook
ansible-playbook cluster-bootstrap.yml

Tip: The cluster-bootstrap playbook is safe to re-run at any time to make sure your cluster is configured correctly.

Bootstrapping the cluster takes a few minutes. When the playbook finishes, you can see the cluster nodes come up using:

kubectl get nodes -w

Note: kubectl is setup automatically inside the container. To use it outside the container as well, simply get the kubeconfig file from that data volume and copy it into ~/.kube/config

Add more worker nodes

If you want to add more workers simply run the worker-add playbook. Specify the desired number of worker nodes. The default cluster has 3 worker nodes. Below command adds 2 more for a total of 5.

ansible-playbook -e desired_num_worker_nodes=5 worker-add.yml

Update Kubernetes

The cluster-upgrade playbook takes care of one by one updating Kubernetes on each of the nodes and restarting services as required. The upgrade does lead to a short unavailability of the apiserver due to the restart of the etcd members. Member restarts take a couple of retries before they succeed, this is caused by ports still being in use.

ansible-playbook cluster-upgrade.yml

Architecture

The initial cluster consists of 3 master nodes and 3 worker nodes. Master nodes are pets, worker nodes are cattle. All nodes run CoreOS.

Master nodes run:

  • infra-etcd2: Etcd2 cluster used for Flanneld overlay networking and Locksmithd
  • flanneld: for the container overlay network
  • locksmithd: to orchestrate automatic updates
  • dockerd
  • kubelet
  • kubernetes-etcd2: Etcd2 cluster used for Kubernetes
  • kube-apiserver
  • kube-scheduler
  • kube-controller-manager
  • kube-proxy

Worker nodes run:

  • flanneld: for the container overlay network
  • locksmithd: to orchestrate automatic updates
  • dockerd
  • kubelet
  • kube-proxy
  • haproxy
  • and your containers of course

Flanneld, Locksmithd, Docker, infra-etcd2 and the kubelet are started using Systemd. All other components most notably kubernetes-etcd2 and kube-* are started by the kubelet.

CoreOS is configured to do automatic updates. Locksmith is configured to make sure only one of the six cluster nodes reboots at the same time. It is also configured to ensure a maintenance window for master nodes between 4 and 5am and for worker nodes between 5 and 6am daily. Automatic updates only include the OS components that are part of CoreOS.

Ingress

Cluster bootstrap includes the nginx-ingress-controller to make services available externally using ingress resources.

Haproxy on each worker node listens on 0.0.0.0:80 and 0.0.0.0:443 and forwards TCP traffic to the ingress controller service.

Simply setup a wildcard DNS entry to point to the IPs of your worker nodes.

Kube-lego is supported by the nginx-ingress-controller but is not automatically installed.

Security

Master and worker nodes each have their own security-groups and only open the required ports between nodes within the same group or between nodes of the other group respectively.

All nodes allow external SSH access. (Required for Ansible unless you use a bastion host.)

On top of the firewall rules enforced by the security groups, all components are configured to communicate via TLS using certificates.

The required certificate authorities and certificates are generated using cfssl automatically.

Known issues / limitations

Kubectl

kubectl is configured to talk to the first master node via IP. If the first master node is unavailable, you need to update your kubectl config to talk to another master node or bring the master node back up. You can of course setup DNS A records for each one of your nodes and use a DNS name instead of the IP in your config.