Unofficial guide to the WT32-ETH01
The WT32-ETH01 is effectively a small, cheap ESP32 development board with Ethernet, WiFi, and GPIO pins, made by a company called "Wireless-Tag" (WT). As of this writing, it's around $15 at JacobsParts and around $7 from AliExpress.
There aren't a ton of ESP32 boards with Ethernet, and the WT32-ETH01 is by far the smallest, cheapest, and simplest. (The OLIMEX ESP32-POE and wESP32 are the other notable options.) So, if you want a cheap-and-cheerful ESP32 board with the reliability of a wired network, the WT32-ETH01 may be a good choice.
It's marketed as a "serial port to Ethernet module" and comes loaded with firmware that lets you send various "AT" commands over 3.3V serial to set up networking, open connections and exchange data. For most of us, it's more interesting to just flash our own programs on the unit and use standard ESP32 networking libraries.
Nobody knows much about the WT company. Don't expect support, and don't lock yourself in too much. Also see Luberth Dijkman's notes on the part.
| EN ⏻ | WT32-ETH01 (ESP32) |
⭕ IO1 (reserved) | 💬 TXD | |
| GND ⏚ | ⭕ IO3 (reserved) | 🗨️ RXD | ||
| 3.3V ⚡ | ⭕ IO0 (reserved) | ⏱️ REFCLK and 💻 BOOT | ||
| pull low to reset | EN ⏻ | ⏚ GND | ||
| ADC1 CH4 📈 | IO32 | ⬅️ IO39 (in only) | 📈 ADC1 CH3 | |
| ADC1 CH5 📈 | IO33 | ⬅️ IO36 (in only) | 📈 ADC1 CH0 | |
| IO5 | 📉 ADC2 CH3 | |||
| IO17 | 📉 ADC2 CH6 | |||
| GND ⏚ | ||||
| 3.3V ⚡ | ⬅️ IO35 (in only) | 📈 ADC1 CH7 | ||
| GND ⏚ | 📉 ADC2 CH0 | |||
| 5V ⚡ | ||||
| ethernet link light | LINK 🖧 | ⏚ GND |
LEGEND
⭕ - Not recommended for application use
⬅️ - Input only
📈 - Analog input on ADC1
📉 - Analog input on ADC2 (conflicts with wi-fi)
Also see the data sheet (an older version has better English labels), and pin reference for the ESP32 module itself.
Some documents (like this listing) have pins IO5 and IO35 swapped in comparison to the layout above. All the physical hardware I've seen has the pins laid out as above, but check to make sure!
There are limitations on several of the pins; see "Strapping Pins" (section 3.3) in the processor data sheet.
IO0: At boot, must be pulled low to program, must float or be pulled high to boot normally. After booting, used to receive the Ethernet 50Mhz clock (enabled by IO16). Best to avoid any other use.
IO1: ESP32 serial output. Used when programming and active by default when running. Best to avoid any other use.
IO2: At boot, must float or be pulled low to program. You can use this pin (especially for output) but make sure nothing pulls it high while booting.
IO3: ESP32 serial input. Used when programming and active by default when running. Best to avoid any other use.
IO5, IO15 (MTDO): At boot, IO5 controls whether ESP32 libraries will print debug messages to the serial port (IO1). Also at boot, IO5 and IO15 together control timings of the module that lets the ESP32 act as an SD card. You are probably not using that module, so you can use these pins (especially for output) but note the effect on debug chatter if pulled while booting.
IO12 (MTDI): At boot, must float or be pulled low or the chip won't work (wrong voltage). You can use this pin (especially for output) after booting, but make sure nothing pulls it high while booting.
IO35, IO36, IO39: These pins are input only, but are otherwise free to use.
You may supply 3.3V power on the 3V3 pins, or 5V power on the 5V pins, but not both at once!
The schematic lists an "LM1117F-1.8V" voltage regulator, which is clearly wrong-- the output is 3.3V, not 1.8V, and also the actual part on the board is marked "AMS1117-3.3". If this were a true AMS1117 it would have a max input of 15V and thermal protection, but it doesn't actually seem to have either; with 12V input, many WT32-ETH01 parts will generate smoke. Probably it's a low-spec AMS1117 knock-off of some kind. So, I'd limit its input to 6V or so, or use your own 3.3V source if you need to.
The WT32-ETH01 does not support Power over Ethernet (PoE), you'll need an external "splitter" if you want that.
The WT32-S1 module (silver box) includes an R-C circuit on EN with 10KΩ × 0.1µF = 1msec time constant. The WT32-ETH01 board includes a separate R-C circuit for the LAN8720A Ethernet controller, also with 1msec time constant. These are quite fast, so if input voltage ramps slowly, the chip may not start reliably, as discussed in this thread.
This can be fixed if necessary by adding another capacitor (e.g. 10µF for 100msec of reset delay), a proper reset supervisor, or a power supply/regulator with a PGOOD (or /RESET) signal you can tie to EN.
Contributed by Dakota Winslow
Included here is a KiCad symbol and footprint. The symbol is arranged by actual physical pin number (rather than grouped by pin type) to make it easier to design circuits with few overlapping traces. I tried to be as descriptive as possible, but ESP32 pins all have many functions so consult other general ESP32 documentation for additional information about the pins. Note that some of the pin labels differ from what is on the board itself; the marks on the board indicate uses for the built-in firmware, which you will almost certainly replace. I made these from sporadic documentation (most of which is linked to in this repo!) but they have been tested in my own projects so I have some confidence. Obviously they are provided with no warranty. Caveat emptor.
Astute readers will have noticed this part has no USB port, so you need an adapter of some kind. There are several possibilities, listed below; whichever one you use, PlatformIO's WT32-ETH01 board support or the Arduino IDE ESP32 add-on (selecting ESP32 Dev Board) should work for programming, or you can use esptool.py directly if you're hardcore. (I'm not that hardcore.)
The most convenient programming solution is a gizmo like M5Stack's ESP32 Downloader (I use this) or wESP32-Prog (untested, but ought to work). These products include a USB-serial adapter and an automatic bootloading circuit. They have 6 pins (in different orders, sadly) that connect to the 6 "programming" pins at the top (WiFi antenna end) of the WT32-ETH01, at which point programming should work. When I design carrier boards for the WT32-ETH01, I route those 6 pins to a 6-pin header laid out for the programmer. If you're working with a raw board, you can use jumper wires like these.
When wiring up the gizmo, make sure gizmo RX goes to WT32-ETH01 TX and vice versa. Also mind the power connections; the M5Stack programmer has a 3.3V output, the wESP32-Prog has a 5V output, make sure you use the right power pin if you want the programmer to power the board. (The 5V input isn't actually in the top 6 "programming pins", but it is labeled.)
You can also program the WT32-ETH01 with a regular USB-serial adapter, but it is a bit tricky:
- You need a 3.3V TTL adapter, not 5V (and certainly not RS-232!)
- To load code, the ESP32 needs the IO0 (BOOT) pin grounded while toggling EN
- You can manually connect those pins to ground (with wires, or buttons) but this gets old fast
- Or, use automatic DTR/RTS bootloading, which needs this mini circuit (credit cyberboy666)
When wiring up a serial adapter, make sure adapter RX goes to WT32-ETH01 TX and vice versa. You will also need to power the WT32-ETH01 somehow, of course.
If you don't have a downloader gizmo or serial adapter, but do have an Arduino Uno or similar with onboard USB-serial, you can use that (credit comporder1). Remove the Arduino microcontroller IC, then use four wires to link 3v3, GND, TX, and RX between the Arduino and WT32-ETH01. (Do NOT cross TX/RX with this method.) You will need to manually connect IO0 (BOOT) to ground while powering on the WT32-ETH01 to put it in bootloader mode, but then programming should work.
WiFi is internal to the ESP32 and works "out of the box", but wired Ethernet takes a bit of configuration.
The ESP32-Arduino "Ethernet" library should work, though I haven't tried it. You will need to call something like this (untested!!):
ETH.begin(1, 16, 23, 18, ETH_PHY_LAN8720);
I personally use code like this based on ESP-IDF interfaces:
#include <esp_netif.h>
#include <esp_netif_types.h>
...
// https://esphome.io/components/ethernet.html
ESP_LOGD(TAG, "Initializing Ethernet MAC for WirelessTag WT32-ETH01...");
eth_mac_config_t mac_config = ETH_MAC_DEFAULT_CONFIG();
mac_config.clock_config.rmii.clock_mode = EMAC_CLK_EXT_IN;
mac_config.clock_config.rmii.clock_gpio = EMAC_CLK_IN_GPIO;
mac_config.smi_mdc_gpio_num = 23;
mac_config.smi_mdio_gpio_num = 18;
mac_config.sw_reset_timeout_ms = 1000; // from ETH.cpp
mac = esp_eth_mac_new_esp32(&mac_config);
ESP_LOGD(TAG, "Initializing Ethernet PHY (LAN8720A) for WT32-ETH01...");
eth_phy_config_t phy_config = ETH_PHY_DEFAULT_CONFIG();
phy_config.phy_addr = 1;
phy_config.reset_gpio_num = -1;
phy = esp_eth_phy_new_lan87xx(&phy_config);
// Enable external oscillator (pulled down at boot to allow IO0 strapping)
ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_16, GPIO_MODE_OUTPUT));
ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_16, 1));
ESP_LOGD(TAG, "Starting Ethernet interface...");
// Install and start Ethernet driver
esp_eth_config_t eth_config = ETH_DEFAULT_CONFIG(mac, phy);
esp_eth_handle_t eth_handle = nullptr;
ESP_ERROR_CHECK(esp_eth_driver_install(ð_config, ð_handle));
esp_netif_config_t const netif_config = ESP_NETIF_DEFAULT_ETH();
global_netif = esp_netif_new(&netif_config);
auto const eth_netif_glue = esp_eth_new_netif_glue(eth_handle);
ESP_ERROR_CHECK(esp_netif_attach(global_netif, eth_netif_glue));
ESP_ERROR_CHECK(esp_eth_start(eth_handle));
The data sheet gives a pretty good overview of the product, including a system block diagram:
- LAN8720A is the Ethernet physical layer controller (PHY)
- WT32-S1 is WT's ESP32 module (metal box), a (discontinued?) ESP32-WROOM-32E-N4 clone based on the same ESP32-D0WD-V3 chip, with 4MB (32Mb) of flash (no PSRAM)
- "Left Interface" and "Right Interface" are just the two pin headers
- "烧录接口" means "programming interface" (the six topmost pins)
There are multiple revisions of the device -- I've seen "V1.2" and "V1.4" on the silkscreen, and the trace routing does differ -- but the differences are unknown. You can get it with or without pin headers pre-soldered on.
Finally, there's a schematic floating around. Its provenance and accuracy are unknown, but it's been helpful to me.
- Post KiCad files for
footprints, breakout boards, and programming connectors - Discussion of issues reported elsewhere?