This is the central repository for OreSat firmware development.
OreSat uses ChibiOS, a Real Time Operating System (RTOS), for Command, Communication, and Control (C3), as well as for its various subsystems. All subsystems communicate via the ECSS CANbus Extension Protocol which is itself based on the CANopen protocol stack and implements the CCSDS Spacecraft Onboard Interface Services recommendations. The C3 system controller manages the overall satellite, as well as critical communications with ground stations. Subsystems handle specific aspects of satellite operation. The various subsystems are listed below.
Further general documentation can be found here
In order to get started developing for OreSat, you must clone this repository and initialize the ChibiOS and CANopenNode submodules after cloning this respository. In addition, you must have the necessary toolchain components to build, interface, and debug a board.
Cloning requires git or some GUI variant of it to clone the
repository. An example of cloning via the command line is shown below.
username@hostname:~
➜ cd Projects
username@hostname:~/Projects
➜ git clone git@github.com:oresat/oresat-firmware.git
Cloning into 'oresat-firmware'...
remote: Enumerating objects: 314, done.
remote: Counting objects: 100% (314/314), done.
remote: Compressing objects: 100% (203/203), done.
remote: Total 7257 (delta 217), reused 194 (delta 110), pack-reused 6943
Receiving objects: 100% (7257/7257), 5.55 MiB | 32.28 MiB/s, done.
Resolving deltas: 100% (4838/4838), done.
username@hostname:~/Projects
➜ cd oresat-firmware
username@hostname:oresat-firmware on master
➜
Once the repository is cloned, you need to initialize the submodules. Additionally, this step needs to be done any time submodule references are updated. This is accomplished by the following command.
git submodule update --init
An example of this is shown below
username@hostname:oresat-firmware on master
➜ git submodule update --init
Submodule 'ChibiOS' (https://github.com/ChibiOS/ChibiOS.git) registered
for path 'ChibiOS'
Submodule 'common/CANopenNode'
(https://github.com/heliochronix/CANopenNode.git) registered for path
'common/CANopenNode'
Cloning into '/home/username/Projects/oresat-firmware/ChibiOS'...
Cloning into
'/home/username/Projects/oresat-firmware/common/CANopenNode'...
Submodule path 'ChibiOS': checked out
'81e586a948125ef1d885f7ddbdcf6591883ff594'
remote: Enumerating objects: 70, done.
remote: Counting objects: 100% (70/70), done.
remote: Total 92 (delta 70), reused 70 (delta 70), pack-reused 22
Unpacking objects: 100% (92/92), 17.81 KiB | 588.00 KiB/s, done.
From https://github.com/heliochronix/CANopenNode
* branch 58836f4083b3607368471f48711d7c1b03576ce8 ->
FETCH_HEAD
Submodule path 'common/CANopenNode': checked out
'58836f4083b3607368471f48711d7c1b03576ce8'
username@hostname:oresat-firmware on master
➜
This project requires the following set of tools to build/write/debug firmware. Please refer to your OS documentation or package installation tool to determine how to install these tools, as it varies between systems.
Tools required:
- make
- arm-none-eabi-gcc
- arm-none-eabi-gdb (may require a symlink to gdb-multiarch on Debian systems)
- stlink (Preferred method of programming/debugging)
- openocd (Optional, not required if stlink tools installed)
PLEASE NOTE: If you use OpenOCD, the latest "official" release of OpenOCD in package managers is several years old. You MUST build it from source for it to work with our boards, as there have been over 1000 commits since the last official release and several of our boards were added since then.
Please refer to Platform Specific Installation Instructions for details on how to do this on a per-system basis.
To test that your build system works correctly, it's recommended that you build one of the app_blinky applications and write it to a dev board successfully. Here are the links for the various versions of the app with further documentation:
Once you have a working toolchain in place, the next step is to copy an existing app_template for your microcontroller to a new app_projectname. The currently supported MCUs for OreSat are listed below, and link to the relevant folders and READMEs.
General Information and Overview (start with the README.)
If the a submodule reference gets updated in oresat-firmware, run the following command again to sync to the proper reference and checkout a working copy:
git submodule update --init