bigjosh/TSL

Issues

• Add a license

  #65 opened a year ago
  3

• Tie EVIN pin to RTC_VCC

  #63 opened 6 years ago
  0

• Quadruple check orientation of LEDs on ver6

  #62 opened 6 years ago
  1

• Make firmware check PCB version and then open or close MOS appropriately.

  #61 opened 6 years ago
  0

• Replace backup CAPs with shorter ones so LCD can fit flatter now that RTC is low version

  #60 opened 6 years ago
  1

• Copper between mounting hole and switch pad does not match gerbers

  #59 opened 6 years ago
  0

• Remove silk from around the endcap contact plate

  #58 opened 6 years ago
  0

• Update firmware for new backup power circuit

  #57 opened 6 years ago
  0

• Mounting holes too tight with new plating

  #56 opened 6 years ago
  0

• Reduce footprint of ATXMEGA center pad

  #55 opened 6 years ago
  0

• Use virtual ports on the FOUT pin to reduce power

  #54 opened 7 years ago
  1

• Rubbing causes spurious resets

  #53 opened 7 years ago
  1

• "ClockError” failures after programming

  #52 opened 7 years ago
  1

• Skipped counts from rubbing

  #51 opened 7 years ago
  1

• Use optimal code generated code to implement digit updating

  #50 opened 6 years ago
  1

• Internally sampled voltage is consistantly ~0.2V lower than real Vcc

  #49 opened 7 years ago
  0

• Test pin shows clock time on power up?

  #48 opened 7 years ago
  1

• Occasional and transatory differnece calculation failure?

  #47 opened 7 years ago
  0

• Add (c) egg

  #46 opened 7 years ago
  1

• Check for low battery

  #45 opened 7 years ago
  1

• Try to make more room on the PCB for the level getting bent under the trigger switch

  #43 opened 7 years ago
  1

• Deal with 100 year rollover?

  #42 opened 7 years ago
  0

• Should we show anything on the display on a warm start?

  #41 opened 7 years ago
  2

• Get rid of silk pin 1 dot on XMEGA

  #40 opened 7 years ago
  0

• Pick pattern for flash

  #39 opened 7 years ago
  1

• Can we save some cycles by skipping ISR on FOUT interrupts?

  #38 opened 7 years ago
  1

• Add low battery detection

  #37 opened 7 years ago
  1

• What actual 8 seg messages should we show on time lost and low batt?

  #36 opened 7 years ago
  5

• Reset RTC on trigger to 1PPS is exactly synced to pull

  #35 opened 7 years ago
  1

• Use smaller RX8900 variant?

  #34 opened 7 years ago
  1

• RX8900 footprint too small

  #33 opened 7 years ago
  1

• Battery holder alignment holes too big

  #32 opened 7 years ago
  0

• Move FOUT to PORTB2 (pin 59) so it can use RISING interrupt

  #31 opened 7 years ago
  0

• No connection from BAT-POS to Vcc!

  #30 opened 7 years ago
  1

• What to try two LEDs in the middle for symmetry and the give the flash a little sparkle by sequencing them?

  #29 opened 7 years ago
  0

• For the LCD pins, can we move the pins up a bit and keep the batteries centered?

  #28 opened 7 years ago
  0

• Trigger switch should be more centered?

  #27 opened 7 years ago
  0

• Ahhh! RIGHT HAND SWITCH!

  #26 opened 7 years ago
  1

• No traces on back side of PCB where they could short against end cap

  #25 opened 7 years ago
  1

• Can we update the label on the PCB?

  #24 opened 7 years ago
  2

• Vias and traces under the ATMEGA

  #23 opened 7 years ago
  1

• Potential short where board is screwed down to cap?

  #22 opened 7 years ago
  1

• Try to put a keep out on the bottom side of the board where the mounting screws are?

  #21 opened 7 years ago
  1

• Put some ISP pads really physically close to the XMEGA

  #20 opened 7 years ago
  1

• Undersize mounting screw holes

  #19 opened 7 years ago
  1

• Test break away tab for trigger

  #18 opened 7 years ago
  1

• Matte black soldermask

  #17 opened 7 years ago
  0

• Switch to other-handed button

  #16 opened 7 years ago
  1

• breakaway finger on trigger pull?

  #15 opened 8 years ago
  0

• LED flash on trigger?

  #14 opened 7 years ago
  0