bigtreetech/BIGTREETECH-OCTOPUS-V1.0

Issues

• Octopus Pro V1.0 Difference between STM32F429GT6 and STM32F446ZET6

  #174 opened a month ago by motoyasu-atsumi
  0

• Robotics

  #157 opened a year ago by YeetParry
  4

• motors not moving

  #173 opened a month ago by pl96andy
  0

• Steppers getting mixed up

  #172 opened a month ago by Roboter32
  1

• BTT Octopus V1.1 with TMC2209 and Marlin 2.1.2.x: Bad response! Error: All LOW

  #171 opened 2 months ago by AlbanT
  0

• Octopus HE0 PIN discrepancy?

  #170 opened 3 months ago by DevlshOne
  0

• Stock firmware for octopus pro v1.1 does not compile

  #151 opened a year ago by ElfyShort
  4

• cannot flash firmware.bin and cannot update bootloader?

  #169 opened 5 months ago by spikar85
  0

• A small mistake on electronic drawings

  #167 opened 8 months ago by Escrich
  0

• Board Not Connecting to COM Port

  #166 opened 8 months ago by filsh
  0

• Driver drv8825 plugged in the wrong way, board defective?

  #165 opened 8 months ago by Skippydi
  3

• BIGTREETECH Octopus - SCH.pdf NO U6 chip mentioned

  #163 opened a year ago by usama0300854
  1

• Bl touch sensor not triggering when Z homing

  #147 opened 2 years ago by mikedattolo
  2

• Btt octopus v1.1 with mks ts35 e3 v2

  #164 opened 10 months ago by andelsalam
  0

• Manual doesn't actually tell you how to set STEP/DIR mode

  #158 opened a year ago by spyderdyne
  2

• more than 2 Z-Endstops not homing with Marlin on Octopus 1.1

  #161 opened a year ago by tu77
  0

• Unable to read tmc uart 'stepper_x' register IFCNT || Unable to read tmc uart 'stepper_z' register IFCNT

  #119 opened 3 years ago by JanSimancik
  6

• Problems with Octopus v1.1

  #141 opened 2 years ago by ctra0031
  3

• Issue with communication in UART mode (more than 4 TMC2209 drivers)

  #159 opened a year ago by Coatl1987
  0

• Status light is not Blinking

  #155 opened a year ago by shreypatel810
  1

• BTT Octopus v1.1BLtouch J43

  #154 opened a year ago by Jarewa
  1

• help needed, to make work accelerometer on SPI3

  #156 opened a year ago by Escrich
  1

• No connection over usb-c ant uart

  #153 opened a year ago by Afrem444
  6

• Add 128Kib bootloader for STM32H723 board

  #138 opened 2 years ago by trevor-pfeil
  2

• Marlin Fails to Auto-Build in Visual Studio

  #152 opened a year ago by SmokinPete55
  0

• Can't establish a serial communication

  #146 opened 2 years ago by lucaguida39
  3

• Platform.ini environment variables name changed

  #150 opened 2 years ago by djrogge
  0

• Octopus 1.1 won't flash firmware

  #148 opened 2 years ago by TamyraT
  2

• octopus v1.1 cant control heater independently

  #149 opened 2 years ago by rds11080
  0

• E0 Motor4 non functional

  #143 opened 2 years ago by HillDweller117
  1

• Flashing bootloader and firmware after MCU replacement

  #145 opened 2 years ago by Ancharas
  1

• Writing diagram / Instructions for the Octopus used with an Ender 5 s1 / Creality Sprite?

  #144 opened 2 years ago by sammcj
  0

• missing documentation for Pro variant

  #139 opened 2 years ago by power-max
  2

• Compilation issue : #define F_CPU SystemCoreClock

  #133 opened 2 years ago by DaLiV
  4

• install of the BTT ESP32 install on Octopus v1.1 needed also....

  #123 opened 2 years ago by WesMcGee68
  6

• Idex system not homing 2nd extruder

  #142 opened 2 years ago by polamoros
  0

• Octoboard 1 407 bootlader

  #140 opened 2 years ago by Ct87
  0

• Octopus Pro 429 Thermistor problem

  #137 opened 2 years ago by reinharm1959
  0

• More problems than its worth!!

  #120 opened 3 years ago by Cabinfourus
  3

• No USB Connection possible

  #129 opened 2 years ago by cwagenl
  3

• Maximum Heater Wattage

  #134 opened 2 years ago by serenewaffles
  1

• Sure. Here it is. It's not pretty but it works.

  #135 opened 2 years ago by Sagittariin
  0

• how/where to connect hall filament width sensor from klipper

  #121 opened 2 years ago by seebaer1976
  1

• Raspberry Pi J26 no serial connectivity (Marlin)

  #131 opened 2 years ago by westhedge
  2

• BigTreeTech TFT TouchScreen Touchscreen mode possible? Or add that mode please.

  #126 opened 2 years ago by Trackhe
  2

• Octopus V1.1 - Z_MULTI_ENDSTOPS - Not working

  #128 opened 2 years ago by lukasloetkolben
  0

• Can't compile because the Z-Endstop inverting requires it to be false

  #127 opened 2 years ago by FortnitePs5
  1

• Missing pinout for stepper drivers

  #125 opened 2 years ago by Dakkaron
  0

• Unable to update Octopus v1 bootloader

  #124 opened 2 years ago by dsplendido
  3

• Octopus v1.1 not responding to usb-c

  #122 opened 2 years ago by 12Testing3
  0