bigtreetech/BIQU-B1

Issues

• bltouch

  #53 opened 7 months ago by Sheller19
  1

• Necessary firmware BIQU B1 SKR 1.4

  #52 opened 9 months ago by Gintaras-sur
  4

• Extruder led don't work

  #14 opened 4 years ago by milan8791
  1

• Nozzle Replacement !

  #51 opened 9 months ago by Sheller19
  1

• CNCFAN part in hotmode v.1 board doesn't work

  #34 opened 3 years ago by Moreirao
  2

• BIQU B1 SKR V1.4 WITH MICROPROBE V2 FIRMWARE NEEDED! please!

  #49 opened a year ago by fabianovm
  2

• B1 glitching to home button

  #50 opened a year ago by Rafin971
  2

• Update problem

  #48 opened a year ago by eltiodemo
  0

• Can you control the Hot End RGB LED via GCODE?

  #4 opened 4 years ago by poldim
  5

• keine Verbindung zum Drucker

  #46 opened 2 years ago by matthias-12
  3

• Upgrading B1 with TMC2226 question

  #45 opened 2 years ago by koiker
  1

• Firmware without BLTouch where?

  #47 opened 2 years ago by DavidFFerreira
  0

• Biqu B1 Knob Led not working

  #42 opened 2 years ago by Cos19
  11

• No Hot END RGB

  #13 opened 4 years ago by tomich
  2

• Abnormal X & Y sounds from steppers after firmware 2.0.7.x update

  #28 opened 3 years ago by MattRK
  26

• Using extruder E1 instead of E0 - TMC Errors and over-extrusion

  #44 opened 2 years ago by aguinaldoabbj
  3

• E0 doesnt work

  #19 opened 4 years ago by delorean-dev
  7

• Where does the cable go? I don't know!

  #40 opened 3 years ago by kazivier-vermillion
  3

• B1 IDEX

  #41 opened 2 years ago by Kharysma85
  0

• Enable Arc Support in the firmware

  #26 opened 4 years ago by Convincent
  1

• Power Loss Recovery now working

  #43 opened 2 years ago by vinicius2p
  0

• Runout sensor

  #39 opened 3 years ago by Nha-Krul
  1

• firmware source request

  #37 opened 3 years ago by Ejay-3D
  2

• [BUG] Screen switches from Marlin mode to TFT when confirming a print.

  #6 opened 4 years ago by blueeagle69
  1

• new biqu b1 with mother srk 2.0 problem

  #38 opened 3 years ago by armuz79
  0

• Wrong nozzle position when running Z Offset

  #11 opened 4 years ago by Ejay-3D
  2

• Corner Bed Leveling with BLTouch not working properly

  #35 opened 3 years ago by Culain
  0

• BIQU B1 upgrade kit

  #31 opened 3 years ago by Markeydoo
  6

• Question: FANs Configuration SKR v2

  #33 opened 3 years ago by emiliorizzo
  1

• BIQU B1 HEATING FAILED

  #32 opened 3 years ago by ijaxbr
  2

• TFT corruption

  #30 opened 3 years ago by Lecrapouille
  0

• Cannot switch off the printer from software

  #29 opened 3 years ago by Lecrapouille
  0

• Temperatures are integer, PID autotune delivers bad results

  #27 opened 3 years ago by lars-danielis
  0

• please publish schematics for the board with the USB-C connector in the hotend

  #10 opened 4 years ago by FotoFieber
  5

• Auto nivelación con censor tipo bltouch

  #25 opened 4 years ago by Puni2404
  0

• Weird moire on walls

  #12 opened 4 years ago by overx212
  1

• biqu b1

  #24 opened 4 years ago by jorrdanna
  14

• Bed leveling not enebled

  #21 opened 4 years ago by stelioc66
  7

• Next release date?

  #22 opened 4 years ago by GrahamJB
  2

• SD card Adapter & SD card

  #23 opened 4 years ago by janf228
  0

• illegal flash app

  #9 opened 4 years ago by pentabene
  4

• Entering M28 gcode command on TFT command console send printer into error.

  #20 opened 4 years ago by emklap
  3

• Bad icon on the TFT 35 screen after firmeware update

  #18 opened 4 years ago by Poufpouf57420
  1

• August firmware freezes up one axis

  #17 opened 4 years ago by plank3ffect
  1

• ERR: MAXTEMP: E1

  #16 opened 4 years ago by dudman
  0

• Extruder rgb led don't work

  #15 opened 4 years ago by milan8791
  0

• provide marlin config with binary firmware

  #8 opened 4 years ago by elric91
  1

• Air shroud - which material and settings?

  #7 opened 4 years ago by Sebazzz
  2

• illegal flash app

  #3 opened 4 years ago by Ejay-3D
  2

• Cura profile cannot be imported

  #2 opened 4 years ago by Sebazzz
  2