bigtreetech/Eddy

Issues

• Option 'sensor_type' is not valid in section 'probe_eddy_current btt_eddy'

  #94 opened 13 days ago by Dinhson178
  0

• Eddy Duo CAN RX/TX GPIO Pins

  #92 opened 21 days ago by Nomanpour
  6

• "Error during homing z: Eddy current sensor error" after updating to mainline klipper

  #52 opened 3 months ago by cjhmdm
  11

• good day I keep getting this error when i try to flash the BTT EDDY how do i get around this problem

  #93 opened 19 days ago by subok911
  0

• Eddy CAN instructions

  #91 opened 24 days ago by serbiansky
  3

• Eddy USB not handling chamber temperature

  #84 opened a month ago by Zinput
  3

• Z-Offset Beta Doesn't Do anything at all

  #87 opened a month ago by chrisz99
  1

• Unable to connect Eddy Coil with BTT Kraken board

  #88 opened a month ago by ymarco73
  1

• eddy x_offset, y_offset calibration

  #86 opened a month ago by artem-sedykh
  2

• Error on 'PROBE_EDDY_CURRENT_CALIBRATE': missing CHIP

  #75 opened 2 months ago by maj0r1337
  2

• Implement 'mesh_runs'

  #89 opened a month ago by mf7120
  0

• Error during setup: probe_eddy_current sensor not in valid range

  #77 opened 2 months ago by JostBrand
  6

• Error => avrdude: ser_open(): can't open device "2e8a:0003"

  #85 opened a month ago by Pmoshbr
  1

• probe_eddy_current sensor not in valid range

  #83 opened a month ago by dravida77
  6

• Invalid STEP and/or TARGET parameters resulted in too few expected samples: 1

  #82 opened a month ago by aquari86
  4

• Invalid probe_eddy_current height

  #45 opened 4 months ago by Zaskeller
  9

• Nozzle height too high

  #73 opened 2 months ago by LeandroSQ
  5

• Unknown command:"PROBE_EDDY_CURRENT_CALIBRATE_AUTO"

  #74 opened a month ago by helloITdepartment
  2

• [DOC UPADTE REQ] Bed severe deviation or extreme tilt

  #81 opened a month ago by plandevida
  1

• Failed calibration - frequency not increasing each step

  #79 opened 2 months ago by SinglerGold2
  4

• Failed calibration - frequency not increasing each step

  #44 opened 4 months ago by JonasBouchard
  8

• Eddy with IDEX configuration not yet working

  #80 opened 2 months ago by HenkVisser
  3

• Possible design flaw with BTT manunfacturing process.

  #78 opened 2 months ago by ph0tic
  0

• EddyCoil with BLTouch

  #76 opened 2 months ago by AnthonyTTaylor
  2

• EddyColi V1 EBB42 CAN

  #68 opened 2 months ago by pietja5
  5

• Make does not work

  #72 opened 2 months ago by smokin76
  1

• Failed calibration - frequency not increasing each step

  #70 opened 2 months ago by chrisz99
  2

• Eddy Coil vs Knomi v2 big problem

  #67 opened 3 months ago by borysne
  8

• Eddy Coil Settings for EBB36 (solution in post)

  #71 opened 2 months ago by QuinFromCanada
  1

• Error on 'PROBE_EDDY_CURRENT_CALIBRATE': missing CHIP

  #69 opened 3 months ago by Gansemagne
  3

• Any plans to implement TAP?

  #66 opened 3 months ago by alexvnesta
  1

• Eddy Touch

  #43 opened 4 months ago by 0xfde9
  1

• Nozzle crash after performing Z_TILT_ADJUST with the Eddy coil

  #55 opened 3 months ago by cssi-dev
  4

• PROBE_EDDY_CURRENT_CALIBRATE_AUTO CHIP=btt_eddy doesn't bring up adjustment screen on Voron/Klipper

  #65 opened 3 months ago by drjeh
  1

• gcode command QUERY_PROBE already registered on ender3S1

  #64 opened 3 months ago by Fredlepp
  2

• using eddy coil getting an error option pin is not valid in section probe

  #63 opened 3 months ago by kodil
  1

• Eddy Coil throwing error on bed mesh scan: Unable to obtain probe_eddy_current sensor readings

  #62 opened 3 months ago by Rainforestnomad
  2

• Error on 'PROBE_EDDY_CURRENT_CALIBRATE': missing CHIP

  #58 opened 3 months ago by Mordi1984
  1

• Failed calibration - incomplete sensor data

  #49 opened 4 months ago by Erop1928
  12

• Unknown command:"TEMPERATURE_PROBE_CALIBRATE"

  #61 opened 3 months ago by TheZDog
  1

• Probe triggered prior to movement after moving to klipper main release

  #59 opened 3 months ago by madk71
  2

• Pausing at points during bed mesh after going to klipper main release

  #57 opened 3 months ago by Wakinyantanka
  5

• (FAQ Request) Error: gcode command QUERY_PROBE already registered

  #56 opened 3 months ago by cicada7772
  2

• Rapid BED MESH doesn't work with latest official Klipper

  #60 opened 3 months ago by qq7594599
  1

• Unknown command:"PROBE_DRIFT_CALIBRATE"

  #54 opened 3 months ago by PeperonyPizza
  2

• Eddy Coil - Error during homing probe: Eddy current sensor error

  #50 opened 4 months ago by tome9111991
  21

• homing issues after PROBE_DRIFT_CALIBRATE

  #47 opened 4 months ago by cjhmdm
  13

• PROBE_DRIFT_CALIBRATE Problem

  #46 opened 4 months ago by ej8g82p
  19

• Does the readme needs updating now that it seems like most/all? patches are in main klipper?

  #51 opened 4 months ago by zingo
  6

• Issues with Z after BED_MESH_CALIBRATE

  #48 opened 4 months ago by cjhmdm
  2