/klipper_estimator

Primary LanguageRustMIT LicenseMIT

Klipper print time estimator

klipper_estimator is a tool for determining the time a print will take using the Klipper firmware. Currently it provides the following modes:

  • estimate mode outputs detailed statistics about a print job
  • post-process mode can be used as a Slicer post-processing script, updating the gcode output file with corrected time estimates.
  • dump-moves mode dumps planning data for every move in a file

The estimation is done using an implementation of Klippers kinematics, but may in some cases be slightly off due to rounding modes. If the timing is far off(e.g. more than a minute over a >12 hour print), this is considered a bug.

Note that currently delta kinematic limits are not implemented.

Usage

Basic usage info can be found by running klipper_estimator with no arguments.

Configuration

In order to provide accurate times, klipper_estimator needs printer settings including maximum velocity, acceleration, etc. It can take these either from a config file(--config_file option) or grab them directly from Moonraker(using the --config_moonraker_url option). Note that the Klipper configuration files cannot be used directly.

To experiment with settings, one can use the dump-config command together with --config_moonraker_url to generate a config file based on the current printer settings. The config file can then be modified and used as input for the other commands.

To dump a config, use e.g.:

$ ./klipper_estimator --config_moonraker_url http://192.168.0.21 dump-config > config.json

The config file format is Hjson and thus allows normal JSON with some extensions(see https://hjson.github.io/).

After generating a config, one can use this in other commands like so:

$ ./klipper_estimator --config_file config.json estimate ...

estimate mode

Estimation mode is useful for determining statistics about a print, in order to optimize print times. It gives a high level summary.

Basic usage:

$ ./klipper_estimator [config options] estimate ~/3DBenchy.data
Sequences:
 Run 0:
  Total moves: 42876
  Total distance: 73313.01640025008
  Total extrude distance: 3407.877500000097
  Minimal time: 1h29m9.948s (5349.947936969622)
  Average flow: 1.5321468696371368 mm3/s
  Phases:
    Acceleration: 27m4.291s
    Cruise:       35m1.116s
    Deceleration: 27m4.291s
  Moves:
  Layer times:
         0 => 2.536s
         ... [some lines omitted for brevity]
        48 => 4.834s
  Kind times:
   4m23.463s            => FILL
   2.639s               => Other
   18m0.185s            => SOLID-FILL
   28m29.706s           => WALL-INNER
   38m13.706s           => WALL-OUTER

The calculations are done based only on the commands found in the file, with no regards for macro expansions. This means that print_start type macros will count as zero seconds, as well heat up times, homing, etc. Therefore the time output should be considered a "minimal time", assuming these extra factors take no time.

post-process mode

In post-process mode klipper_estimator directly modifies the filename passed in in-place, updating time estimations in the file.

When using klipper_estimator in post-process mode, simply add a post-processing script in your slicer like so:

/path/to/klipper_estimator --config_moonraker_url http://192.168.0.21 post-process

Change the path and config options to fit your situation.

Currently the following slicers are supported:

  • PrusaSlicer
  • SuperSlicer
  • ideaMaker
  • Cura

In PrusaSlicer and SuperSlicer Post-processing scripts are set in Output Options under Print Settings:

PrusaSlicer and SuperSlicer Post-processing scripts option

Note that ideaMaker does not have support for post-processing scripts, and thus cannot automatically run klipper_estimator on export.

For Cura, use the script in compat/CuraPostProcessing/.

dump-moves mode

The dump-moves mode is used like estimate mode, but instead of providing a summary, move planning data is dumped for every move.

Accurately estimating PRINT_START/PRINT_END macros

Klipper macros can perform arbitrarily complex operations. klipper_estimator has no hope of estimating how long these will take, as the Jinja templates can access any state of the read printer. However it is often the case that the amount of print time actually spent within the macro is constant. A prime example of this is print start macros. The macro may execute homing and heating commands, but the print timer does not start until the first material is extruded. This generally happens when the prime line is started.

This gives rise to an offset in print time that we cannot estimate, but the user can easily measure it after a print is over.

To compensate for this, klipper_estimator understands the following gcode comment(generally syntax followed by some examples):

; ESTIMATOR_ADD_TIME <duration> [description]
; E.g.:
; ESTIMATOR_ADD_TIME 21
; ESTIMATOR_ADD_TIME 21 Print start

When klipper_estimator encounters a comment with this format, it will add the requested duration to the total print time. The time will also be tracked as a "move kind", if the description field is given.

Note that only the upper-case string ESTIMATOR_ADD_TIME, on a separate comment line, will trigger this behaviour. Any whitespace between the ; and E characters will however be ignored.

The intended usage of this functionality is for print start macros, when executed by the slicer. E.g. in PrusaSlicer or SuperSlicer, one might set their print start gcode like this:

; ESTIMATOR_ADD_TIME 20 Prime line
print_start extruder=[first_layer_temperature] bed=[first_layer_bed_temperature]

Building

klipper_estimator is written in Rust. Version 1.58 or newer is required to compile the tool. Assuming a Rust toolchain is installed, along with git, one can build klipper_estimator by running:

$ git clone https://github.com/dalegaard/klipper_estimator.git
$ cd klipper_estimator
$ cargo build --release
// Resulting binary will be at `target/release/klipper_estimator`(.exe on Windows)

Binaries are provided for Windows, Linux, Mac OS X, and Raspberry Pi targets. These can be found under the Releases section. On Linux and Mac OS X, ensure that you give the downloaded file executable permissions. This can be done in the terminal as follows:

$ chmod +x klipper_estimator

Change the filename (last parameter) to match the downloaded file.

For Arch Linux, an AUR package klipper_estimator is available, courtesy of Wilhelm Schuster. Thanks!

Acknowledgements

This project is in no way endorsed by the Klipper project. Please do not direct any support requests to the Klipper project.