BME280 Sensor Driver

https://travis-ci.org/rm-hull/bme280.svg?branch=master

https://coveralls.io/repos/github/rm-hull/bme280/badge.svg?branch=master

Interfacing a Bosch BME280 digital sensor module (capable of sensing temperature, humidity and pressure) in Python 2 or 3 using I2C on the Raspberry Pi. The particular kit I bought can be acquired for a few pounds from eBay. Further technical details for the BME280 sensor can be found in the datasheet [PDF].

GPIO pin-outs

The BME280 is an I2C device, so connecting to the RPi is very straightforward:

P1 Header

For prototyping, the P1 header pins should be connected as follows:

Board Pin	Name	Remarks	RPi Pin	RPi Function
1	VIN	+3.3V Power	P01-1	3V3
2	GND	Ground	P01-6	GND
3	SCL	Clock	P01-5	GPIO 3 (SCL)
4	SDA	Data	P01-3	GPIO 2 (SDA)

Pre-requisites

Ensure that the I2C kernel driver is enabled:

$ dmesg | grep i2c
[    4.925554] bcm2708_i2c 20804000.i2c: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100000)
[    4.929325] i2c /dev entries driver

or:

$ lsmod | grep i2c
i2c_dev                 5769  0
i2c_bcm2708             4943  0
regmap_i2c              1661  3 snd_soc_pcm512x,snd_soc_wm8804,snd_soc_core

If you have no kernel modules listed and nothing is showing using dmesg then this implies the kernel I2C driver is not loaded. Enable the I2C as follows:

Run sudo raspi-config
Use the down arrow to select 9 Advanced Options
Arrow down to A7 I2C
Select yes when it asks you to enable I2C
Also select yes when it asks about automatically loading the kernel module
Use the right arrow to select the <Finish> button
Select yes when it asks to reboot

After rebooting re-check that the dmesg | grep i2c command shows whether I2C driver is loaded before proceeding.

Optionally, to improve permformance, increase the I2C baudrate from the default of 100KHz to 400KHz by altering /boot/config.txt to include:

dtparam=i2c_arm=on,i2c_baudrate=400000

Then reboot.

Then add your user to the i2c group:

$ sudo adduser pi i2c

Install some packages:

$ sudo apt-get install i2c-tools python-pip

Next check that the device is communicating properly (if using a rev.1 board, use 0 for the bus not 1):

$ i2cdetect -y 1
       0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
  00:          -- -- -- -- -- -- -- -- -- -- -- -- --
  10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
  20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
  30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
  40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
  50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
  60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
  70: -- -- -- -- -- -- 76 --

Installing the Python Package

For python2, from the bash prompt, enter:

$ sudo python setup.py install

This will install the Python files in /usr/local/lib/python2.7 making them ready for use in other programs.

Alternatively for python3, type:

$ sudo python3 setup.py install

Cheeseshop install

Alternatively, a version on PyPi is available, just do:

$ sudo pip install RPi.bme280

Software Driver - Example Usage

Once installed, confirm the I2C address (see prerequisites, it will most likely be 0x76 or 0x77) and port.

Then in a python script or REPL:

import smbus2
import bme280

port = 1
address = 0x76
bus = smbus2.SMBus(port)

calibration_params = bme280.load_calibration_params(bus, address)

# the sample method will take a single reading and return a
# compensated_reading object
data = bme280.sample(bus, address, calibration_params)

# the compensated_reading class has the following attributes
print(data.id)
print(data.timestamp)
print(data.temperature)
print(data.pressure)
print(data.humidity)

# there is a handy string representation too
print(data)

This then should print something like:

ee50df9c-3aa3-4772-8767-73b6bb74f30f
2016-11-18 17:33:28.937863
20.563
980.91
48.41
compensated_reading(id=ee50df9c-3aa3-4772-8767-73b6bb74f30f,
    timestamp=2016-11-18 17:33:28.937863, temp=20.563 °C,
    pressure=980.91 hPa, humidity=48.41 % rH)

For a data-logger like application, periodically call bme2.sample(bus, address, calibration_params) to get time-based readings.

See the weatherstation project for a more complete example usage.

References

> TODO

License

The MIT License (MIT)

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

c5fritz1387/bme280