___ _ ___ _ / __|___ _ _ ___ ___| |___ / __|_____ __ _| |__ ___ _ _ ___ | (__/ _ \ ' \(_-</ _ \ / -_) | (__/ _ \ V V / '_ \/ _ \ || (_-< \___\___/_||_/__/\___/_\___| \___\___/\_/\_/|_.__/\___/\_, /__/ |__/ ___ ___ ___ _ ___ | _ \ __/ __|_ _ __ _ __| |__ |___| | / _| (__| '_/ _` / _| / / |_|_\_| \___|_| \__,_\__|_\_\ Welcome to RFCrack - A Software Defined Radio Attack Tool VERSION Update: this has been updated to Python3 and should work but there are all kinds of issues I am running into with firmware versions, sdcc, rfcat etc which may also effect you.. See the RFCat documentation if you run into issues. Developer: @Ficti0n - http://ConsoleCowboys.com CCLabs: http://cclabs.io Blog: console-cowboys.blogspot.com Release Tutorial: https://www.youtube.com/watch?v=H7-g15YZBiI Reversing Signals With RFCrack: https://www.youtube.com/watch?v=XqKoVFyOst0 Release: 1.5 Hardware Needed: (1 Yardstick or 2 for RollingCode) YardStick: https://goo.gl/wd88sr RFCrack is my personal RF test bench, it was developed for testing RF communications between any physical device that communicates over sub Ghz frequencies. IoT devices, Cars, Alarm Systems etc... Testing was done with the Yardstick One on OSX, but RFCrack should work fine in linux. Support for other RF related testing will be added as needed in my testing. I am currently researching keyless Entry bypasses and other signal analysis functionality. New functionality will be added in the future with additional hardware requirements for some advanced attacks. Feel free to use this software as is for personal use only. Do not use this code in other projects or in commercial products. I hold no liability for your actions with this code. Your life choices are your own. Current supported Functionality: --------------------------------- - Replay attacks -i -F - Send Saved Payloads -s -u - Rolling code bypass attacks -r -F -M - Targeted -t -F - Jamming -j -F - Scanning incrementally through frequencies -b -v -F - Scanning common frequencies -k - Compare Live incoming signals to previous signal -k -c -f -u - Graph Signal -n -g -u Usage Examples / Attacks: ------------------------- Live Replay: python RFCrack.py -i Rolling Code: python RFCrack.py -r -M MOD_2FSK -F 314350000 Adjust RSSI Values: python RFCrack.py -r -M MOD_2FSK -F 314350000 -U -100 -L -10 Jamming: python RFCrack.py -j -F 314000000 Scan common freq: python RFCrack.py -k Scan with your list: python RFCrack.py -k -f 433000000 314000000 390000000 Incremental Scan: python RFCrack.py -b -v 5000000 Send Saved Payload: python RFCrack.py -s -u ./captures/test.cap -F 315000000 -M MOD_ASK_OOK With Loaded Config: python RFCrack.py -l ./device_templates/doorbell.config -r Graph a Signal: python RFCrack.py -n -g -u 1f0fffe0fffc01ff803ff007fe0fffc1fff83fff07 Live Signal Identification and Comparison (Use 2 Console Windows): ----------------------------------------------------------------- Setup sniffer: python RFCrack.py -k -c -f 390000000 Setup Analysis: python RFCrack.py -c -u 1f0fffe0fffc01ff803ff007fe0fffc1fff83fff07f -n Useful arguments: ------------------------ -M Change modulation, usually MOD_2FSK or MOD_ASK_OOK -F Change the frequency used in attacks -U upper_rssi signal strength value for rolling Code -L lower.rssi signal strength value for rolling code -S Change Channel Spacing -V Change Deviation of modulation -a Jamming frequency variance from sniffer -s Send packet from a file source -d Save your current device settings into a loadable template after attack completes -l Load previously saved device configuration with attack -n Your using functionality that does not require a yardstick plugged in -u Use saved data in your attack Directories Explained: ---------------------- Saved captures get saved to ./captures directory by default! Live signal identification captures also saved to ./captures directory in capturedClicks.log Device templates are saved and loaded to ./device_templates by default Scanning logs are saved to ./scanning_logs named based on date and time of scanning start Graph comparison images are saved to imageOutput in 2 formats - Live: LiveComparison.png will just be written over on each signal Analysis - Log analysis: Comparison1 Comparison2 format is used and written over on each log analysis Other Notes: ------------------------ Understand that Rolling code is hit or miss due to its nature with jamming and sniffing at the same time, but it works. Just use the keyfob near the yardsticks as if you were stalking your target. It will also require 2 yardsticks, one for sniffing while the other one is jamming. Yardsticks do not send and receive at the same time. And a final note, this is my own test bench for doing research and dev, if you have ideas to make RFCrack better based on realistic use case scenarios, feel free to reach out to me If the ideas are realistic, well thought out, and re-useable use cases I will implement them.