ccztux/modpd

Monitoring Obsessing Data Processor Daemon

Table of Contents

• What is modpd?
• What was the motivation to develop modpd?
• Flowchart
• Registered trademarks
• Known Issues
• Supported monitoring engines
  • modpd >= 3.x.x
  • modpd < 3.x.x
• Requirements
  • Required for building, compiling and installing the NEB modules and modpd
  • Required binaries for the installation of NRDP
  • Required binaries for the installation of NSCA
  • Required by the daemon part of modpd
  • Optionally used binaries which depends on configured features
• Installation on the monitoring site which executes the active checks
  • Download the latest sources of modpd
  • Create the required linux user and set a password
  • Add the user nagios to the modpd group
  • Add the user naemon to the modpd group
  • Build the modpd NEB modules and install them and the modpd daemon
  • Edit the modpd daemon config to meet your requirements
  • Start the modpd daemon
  • Enable the modpd daemon at system boot
  • Add the NEB module to your monitoring engine
    • Add the NEB module to Nagios®
    • Add the NEB module to Naemon
  • Installation of the clients (of your choice)
    • send_nrdp.php
    • send_nsca
• Installation on the monitoring site which accepts the passive checks
  • Installation of the server software (of your choice)
    • NRDP
    • NSCA
• Updating modpd
  • Make a backup
  • Download the latest sources of modpd
  • Build the modpd NEB modules and install them and the modpd daemon
  • Restart your monitoring engine
    • Nagios
    • Naemon
  • Check and merge eventual new configuration variables
  • Restart the modpd daemon
• The daemon
  • Daemon help output
  • File overview
  • Daemon control options
  • Default sample config
  • Example log snippets
    • modpd daemon log snippet
    • modpd NEB module log snippet
• Backup your modpd installation
• Upgrading modpd from 2.x.x to 3.x.x
  • Backup your modpd installation
  • Remove the old installation
    • Stop the modpd daemon
    • Remove the files
    • Remove the NEB module from Nagios®
    • Restart Nagios®
  • Install modpd 3.x.x

What is modpd?

(Monitoring Obsessing Data Processor Daemon)

modpd consists of a NEB module and a daemon written in bash. The NEB module collects data and writes it to a named pipe. The daemon part reads the data from the named pipe and sends the check results via NRDP or NSCA to another monitoring server.

What was the motivation to develop modpd?

There were two reasons:

1. Performance
   It increases the performance of an existing Nagios® 3.x.x installation greatly, because the obsessing commands will be executed by modpd and not by the Nagios® process itself. Nagios® executes the obsessing command after every check, where obsessing is activated and then Nagios® waits, till every obsessing command was executed successfully or timed out.

2. Nagios® 3.x.x stops executing active checks
   On some systems Nagios® 3.x.x stops randomly executing active checks when obsessing is enabled.

Flowchart

Registered trademarks

Nagios®, Nagios Core, NRDP, NSCA, and the Nagios logo are trademarks, servicemarks, registered servicemarks or registered trademarks of Nagios Enterprises. All other trademarks, servicemarks, registered trademarks, and registered servicemarks mentioned herein may be the property of their respective owner(s). The information contained herein is provided AS IS with NO WARRANTY OF ANY KIND, INCLUDING THE WARRANTY OF DESIGN, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE.

Known Issues

• Reloading modpd is causing one invalid dataset #118 If the daemon will be reloaded, one dataset is getting malformed and will be detected as an invalid dataset. Nevertheless you should prefere the reload function over the restart function if you have only changed something in the configuration, because in case of a restart more than one datasets are getting lost.

Supported monitoring engines

modpd >= 3.x.x

• Nagios® 3.4.x
• Naemon 1.3.x

modpd < 3.x.x

• Nagios® 3.4.x

Requirements

Required for building, compiling and installing the NEB modules and modpd

• wget to download the latest release of modpd
• tar to untar the downloaded package of modpd
• make to build the modpd NEB modules
• gcc to compile the modpd NEB modules
• install to install the modpd NEB modules
• strip to strip the modpd NEB binaries
• useradd to add the modpd linux user
• passwd to set a password for the user modpd
• usermod to add users to the modpd group

Required binaries for the installation of NRDP

• wget to download the package
• tar to untar the downloaded package
• cp to copy files
• chown to change the ownership of files
• php to run the application

Required binaries for the installation of NSCA

• wget to download the package
• tar to untar the downloaded package
• make to build the modpd NEB modules
• gcc to compile the modpd NEB modules
• cp to copy files
• chown to change the ownership of files

Required by the daemon part of modpd

• systemctl to control the modpd daemon
• bash (version >= 3)
• whoami to check the user who has started modpd
• pgrep to check if an instance of modpd is already running
• date for logging purposes (Only required if bash version < 4.2, else bash's printf builtin will be used.)
• rm to delete the named_pipe_filename
• mkdir to create directories
• mkfifo to create the named_pipe_filename
• kill to send signals to modpd
• sleep to do nothing :)
• logrotate to rotate modpd's logfile

Optionally used binaries which depends on configured features

• logger to log to the system log
• systemd-cat to log to the system journal
• timeout to start the obsessing jobs with a timeout value
• php in case obsessing_interface is nrdp

Installation on the monitoring site which executes the active checks

Download the latest sources of modpd

Download the latest tarball and extract it:

cd /tmp
wget "https://api.github.com/repos/ccztux/modpd/tarball" -O modpd.latest.tar.gz
tar -xvzf modpd.latest.tar.gz
cd ccztux-modpd-*

Create the required linux user and set a password

useradd -s /sbin/nologin modpd
passwd modpd

Add the user nagios to the modpd group

Do this only, if you use Nagios®!

usermod -aG modpd nagios

Add the user naemon to the modpd group

Do this only, if you use Naemon!

usermod -aG modpd naemon

Build the modpd NEB modules and install them and the modpd daemon

make
make install

Edit the modpd daemon config to meet your requirements

vim /etc/modpd/modpd.conf

Start the modpd daemon

systemctl start modpd

Check if the modpd daemon is running

systemctl status modpd
tail -f /var/log/modpd/modpd.log

Enable the modpd daemon at system boot

systemctl enable modpd

Check if modpd is activated at system boot

systemctl status modpd

Add the NEB module to your monitoring engine

Add the NEB module to Nagios®

Do this only, if you use Nagios®!

Add the modpd NEB module with the editor of your choice to your Nagios® main config file:

(Default Nagios® main config file: /usr/local/nagios/etc/nagios.cfg)

broker_module=/usr/lib64/modpd/modpd_nagios3.o

Set the eventbroker options with the editor of your choice in your main nagios config file:

(Default Nagios® main config file: /usr/local/nagios/etc/nagios.cfg)

event_broker_options=-1

Restart nagios:

systemctl restart nagios

Check if nagios is running:

systemctl status nagios

Check if the modpd NEB module was loaded by nagios:

[root@lab01]:~# grep -i modpd /usr/local/nagios/var/nagios.log
[1582272717] modpd: Copyright © 2017-NOW Christian Zettel (ccztux), all rights reserved, Version: 3.0.0
[1582272717] modpd: Starting...
[1582272717] Event broker module '/usr/lib64/modpd/modpd_nagios3.o' initialized successfully.

Add the NEB module to Naemon

Do this only, if you use Naemon!

Add the modpd NEB module with the editor of your choice to your Naemon main config file:

(Default Naemon main config file: /etc/naemon/naemon.cfg)

broker_module=/usr/lib64/modpd/modpd_naemon.o

Set the eventbroker options with the editor of your choice in your main naemon config file:

(Default Naemon main config file: /etc/naemon/naemon.cfg)

event_broker_options=-1

Restart naemon:

systemctl restart naemon

Check if naemon is running:

systemctl status naemon

Check if the modpd NEB module was loaded by naemon:

[root@lab01]:~# grep -i modpd /var/log/naemon/naemon.log
[1582272717] modpd: Copyright © 2017-NOW Christian Zettel (ccztux), all rights reserved, Version: 3.0.0
[1582272717] modpd: Starting...
[1582272717] Event broker module '/usr/lib64/modpd/modpd_naemon.o' initialized successfully.

Installation of the clients (of your choice)

send_nrdp.php

Official NRDP Documentation by Nagios®

Download the latest tarball and extract it:

cd /tmp
wget "https://api.github.com/repos/NagiosEnterprises/nrdp/tarball" -O nrdp.latest.tar.gz
tar -xvzf nrdp.latest.tar.gz
cd NagiosEnterprises-nrdp-*

Copy the send_nrdp.php script:

cp -av ./clients/send_nrdp.php /usr/libexec/modpd/

Change the file ownership:

chown root:root /usr/libexec/modpd/send_nrdp.php

send_nsca

Official NSCA Documentation by Nagios®

Download the latest tarball and extract it:

cd /tmp
wget "https://api.github.com/repos/NagiosEnterprises/nsca/tarball" -O nsca.latest.tar.gz
tar -xvzf nsca.latest.tar.gz
cd NagiosEnterprises-nsca-*

Build and compile the send_nsca binary:

./configure
make send_nsca

Copy the files:

cp -av ./src/send_nsca /usr/libexec/modpd/send_nsca
cp -av ./sample-config/send_nsca.cfg /etc/modpd/

Change the file ownerships:

chown root:root /usr/libexec/modpd/send_nsca
chown modpd:modpd /etc/modpd/send_nsca.cfg

Edit the send_nsca config to meet your requirements:

vim /etc/modpd/send_nsca.cfg

Installation on the monitoring site which accepts the passive checks

Installation of the server software (of your choice)

NRDP

Official NRDP Documentation by Nagios®

NSCA

Official NSCA Documentation by Nagios®

Updating modpd

Make a backup

Make a backup of your existing installation as described here

Download the latest sources of modpd

Download the latest tarball and extract it:

cd /tmp
wget "https://api.github.com/repos/ccztux/modpd/tarball" -O modpd.latest.tar.gz
tar -xvzf modpd.latest.tar.gz
cd ccztux-modpd-*

Build the modpd NEB modules and install them and the modpd daemon

make
make install

Restart your monitoring engine

Nagios

Restart nagios:

systemctl restart nagios

Check if nagios is running:

systemctl status nagios

Check if the modpd NEB module was loaded by nagios:

[root@lab01]:~# grep -i modpd /usr/local/nagios/var/nagios.log
[1582272717] modpd: Copyright © 2017-NOW Christian Zettel (ccztux), all rights reserved, Version: 3.0.0
[1582272717] modpd: Starting...
[1582272717] Event broker module '/usr/lib64/modpd/modpd_nagios3.o' initialized successfully.

Naemon

Restart naemon:

systemctl restart naemon

Check if naemon is running:

systemctl status naemon

Check if the modpd NEB module was loaded by naemon:

[root@lab01]:~# grep -i modpd /var/log/naemon/naemon.log
[1582272717] modpd: Copyright © 2017-NOW Christian Zettel (ccztux), all rights reserved, Version: 3.0.0
[1582272717] modpd: Starting...
[1582272717] Event broker module '/usr/lib64/modpd/modpd_naemon.o' initialized successfully.

Check and merge eventual new configuration variables

Merge possible changes between the new sample config and your productive one using the tool of your choice like vimdiff:

vimdiff /etc/modpd/modpd.sample.conf /etc/modpd/modpd.conf

Restart the modpd daemon

systemctl daemon-reload
systemctl restart modpd

Check if the modpd daemon is running:

systemctl status modpd
tail -f /var/log/modpd/modpd.log

The daemon

Daemon help output

Usage: modpd OPTIONS

Author:                 Christian Zettel (ccztux)
Last modification:      2023-01-09
Version:                3.0.0

Description:            modpd (Monitoring Obsessing Data Processor Daemon)

OPTIONS:
   -h           Shows this help.
   -c           Path to config file. (Default: /etc/modpd/modpd.conf)
   -e           Error mode. Log bash errors additionally to: /var/log/modpd/modpd.log
                WARNING: This is not intended for use in a production environment!
   -v           Shows detailed version information.

File overview

• /etc/logrotate.d/modpd logrotate config file for the modpd daemon logfile
• /etc/sysconfig/modpd default configuration values for the system unit file
• /usr/bin/modpd modpd daemon
• /etc/modpd/modpd.conf configuration file for the modpd daemon
• /etc/modpd/modpd.sample.conf sample configuration file for the modpd daemon
• /usr/lib/systemd/system/modpd.service systemd unit file for modpd
• /usr/lib64/modpd/modpd_nagios3.o modpd NEB module for Nagios® 3.x.x
• /usr/lib64/modpd/modpd_naemon.o modpd NEB module for Naemon 1.3.x
• /var/lib/modpd/lock/modpd.lock modpd daemon lockfile (will be created by the daemon)
• /var/lib/modpd/rw/modpd.cmd named pipe (will be created by the daemon)
• /var/log/modpd/modpd.log modpd daemon logfile (will be created by the daemon)
• /var/log/modpd/modpd.monitoring.debug.log debug logfile containing raw monitoring data (will be created by the daemon)
• /var/log/modpd/modpd.obsessing.debug.log debug logfile containing processed obsessing data (will be created by the daemon)

Daemon control options

• systemctl status modpd shows the state of the daemon
• systemctl start modpd starts the daemon
• systemctl stop modpd stops the daemon
• systemctl restart modpd restarts the daemon
• systemctl reload modpd reloads the daemon (config will be re-readed)

Default sample config

#!/usr/bin/env bash

#========================================================================================================
#
#  Author:				Christian Zettel (ccztux)
#						2017-05-14
#						http://linuxinside.at
#
#  Copyright:			Copyright © 2017-NOW Christian Zettel (ccztux), all rights reserved
#
#  Project website:		https://github.com/ccztux/modpd
#
#  Last Modification:	Christian Zettel (ccztux)
#						2023-01-09
#
#  Version				3.0.0
#
#  Description:			Config file for modpd (Monitoring Obsessing Data Processor Daemon)
#
#  License:				GNU GPLv2
#
#  This program is free software; you can redistribute it and/or modify
#  it under the terms of the GNU General Public License as published by
#  the Free Software Foundation; either version 2 of the License, or
#  (at your option) any later version.
#
#  This program is distributed in the hope that it will be useful,
#  but WITHOUT ANY WARRANTY; without even the implied warranty of
#  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
#  GNU General Public License for more details.
#
#  You should have received a copy of the GNU General Public License along
#  with this program; if not, write to the Free Software Foundation, Inc.,
#  51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
#
#========================================================================================================


#---------------------------------------------------
# In case of direct execution, write output and exit
#---------------------------------------------------

if [ "${BASH_SOURCE[0]}" == "${0}" ]
then
	printf "\\n%s is a bash config file. Dont execute it directly!\\n\\n" "${0##*/}"
	exit 1
fi



#==========================================================
#
# Modify the following parameters to meet your requirements
#
#==========================================================

#-------------------
# Obsessing settings
#-------------------

# define the obsessing interface
# (valid values: nrdp|nsca)
c_obsessing_interface="nrdp"

# define the host, where check results should be sent to
c_obsessing_host="10.0.0.31"

# define the port, where the obsessing daemon is listening on
c_obsessing_port="443"

# define the separator which should be used
c_obsessing_data_separator="\\x1e"



#----------------------------------------------------------------------
# NRDP specific settings (Needed in case c_obsessing_interface is nrdp)
#----------------------------------------------------------------------

# define the connection protocol
# (valid values: http|https)
c_nrdp_protocol="https"

# define the url path of the nrdp server
c_nrdp_url_path="/nrdp"

# define the nrdp token
c_nrdp_token="12345678"

# define the username, if nrdp basic auth is activated
c_nrdp_username="nrdpuser"

# define the password of the user you have defined in variable: c_nrdp_username with which we sould connect
c_nrdp_password="mySecret"



#----------------------------------------------------------------------
# NSCA specific settings (Needed in case c_obsessing_interface is nsca)
#----------------------------------------------------------------------

# define the path to the config file of send_nsca binary
c_nsca_config_file="/etc/modpd/send_nsca.cfg"



#-----------------------------------------------------------------------------------------
# Proxy settings (Needed in case c_obsessing_interface is nrdp and a proxy should be used)
#-----------------------------------------------------------------------------------------

# enable proxy
c_proxy_enabled="0"

# username to authenticate on proxy server
c_proxy_username="ccztux"

# password to authenticate on proxy server
c_proxy_password="mySecret"

# proxy protocol
# (valid values: http|https)
c_proxy_protocol="https"

# proxy ip or hostname
c_proxy_ip="10.0.0.10"

# proxy port
c_proxy_port="3128"






#================================================================
#
# ONLY MODIFY THE FOLLOWING PARAMETERS, IF YOU KNOW, WHAT YOU DO!
#
#================================================================

#--------
# Logging
#--------

# enable log to file
# (valid values: 1|0)
c_log_to_file="1"

# enable log to stdout"
# (valid values: 1|0)
c_log_to_stdout="0"

# enable log to system logfile
# (valid values: 1|0)
c_log_to_syslog="0"

# enable log to system journal
# (valid values: 1|0)
c_log_to_journal="0"

# timestamp format for log messages
# (HINT: have a look at: 'man strftime')
c_log_timestamp_format="%Y-%m-%d %H:%M:%S"

# log invalid data
# (valid values: 1|0)
c_log_invalid_data="1"



#----------
# Debugging
#----------

# enable debug log of the raw data processed via c_obsessing_interface
# (valid values: 1|0)
c_debug_log_obsessing_data="0"

# enable debug log of the raw monitoring data submitted to the named pipe
# (valid values: 1|0)
c_debug_log_monitoring_data="0"

# time in seconds when the debug logfile should be truncated
c_debug_log_truncate_interval="604800"



#-------------
# Job settings
#-------------

# enable job timeout
c_job_timeout_enabled="1"

# job timeout in seconds (recommended: c_job_exec_interval * 2)
c_job_timeout="8"

# job execution interval in seconds
c_job_exec_interval="4"

# job max bulk size
c_job_max_bulk_size="250"

# log unsuccessful job commands
# (valid values: 1|0)
c_job_command_log_nok="1"

# log timed out job commands
# (valid values: 1|0)
c_job_command_log_timeout="1"

# log successful job commands
# (valid values: 1|0)
c_job_command_log_ok="0"

# log raw data in case a job was not processed successfully
# (valid values: 1|0)
c_job_command_log_nok_data="1"

# retransmit data in case a job was not processed successfully
# (valid values: 1|0)
c_job_nok_retransmit="1"



#------
# Stats
#------

# enable stats logging
c_stats_enabled="1"

Example log snippets

modpd daemon log snippet

2021-01-07 16:10:01 |   7084 | checkLogHandlerRequirements | modpd 3.0.0 starting... (PID=7084)
2021-01-07 16:10:01 |   7084 | checkLogHandlerRequirements | We are using the config file: '/etc/modpd/modpd.conf'
2021-01-07 16:10:01 |   7084 |                 getExecUser | Get user which starts the daemon...
2021-01-07 16:10:01 |   7084 |                 getExecUser | modpd was started as user: 'nagios'
2021-01-07 16:10:01 |   7084 |            checkBashVersion | Checking bash version...
2021-01-07 16:10:01 |   7084 |            checkBashVersion | Bash version: '4' meets requirements
2021-01-07 16:10:01 |   7084 | checkAlreadyRunningInstance | Check if another instance of: 'modpd' is already running...
2021-01-07 16:10:01 |   7084 |                   checkLock | Check if lock file: '/var/lib/modpd/lock/modpd.lock' exists and if it is read and writeable...
2021-01-07 16:10:01 |   7084 |                   checkLock | Lock file doesnt exist
2021-01-07 16:10:01 |   7084 | checkAlreadyRunningInstance | No other instance of: 'modpd' is currently running (Lockfile: '/var/lib/modpd/lock/modpd.lock' doesnt exist and no processes are running)
2021-01-07 16:10:01 |   7084 |                     setLock | Check if daemon lock directory: '/var/lib/modpd/lock' exists and permissions to set lock are ok...
2021-01-07 16:10:01 |   7084 |                     setLock | Script lock directory exists and permissions are ok
2021-01-07 16:10:01 |   7084 |                     setLock | Setting lock...
2021-01-07 16:10:01 |   7084 |                     setLock | Setting lock was successful
2021-01-07 16:10:01 |   7084 |              checkNamedPipe | Check if named pipe: '/var/lib/modpd/rw/modpd.cmd' exists and if it is read/writeable...
2021-01-07 16:10:01 |   7084 |              checkNamedPipe | Named pipe doesnt exist
2021-01-07 16:10:01 |   7084 |             createNamedPipe | Creating named pipe...
2021-01-07 16:10:01 |   7084 |             createNamedPipe | Creating named pipe was successful
2021-01-07 16:10:01 |   7084 |             buildJobCommand | Building job command...
2021-01-07 16:10:01 |   7084 |             buildJobCommand | We build the following job command: '/usr/bin/timeout --signal=TERM 8 /usr/bin/php /usr/libexec/modpd/send_nrdp.php --usestdin --delim="�" --token="[HIDDEN FOR SECURITY]" --url=https://nrdpuser:[HIDDEN FOR SECURITY]@10.0.0.74:443/nrdp'
2021-01-07 16:10:01 |   7084 |                       _main | Ready to handle jobs...
2021-01-07 16:11:01 |   7084 |               dataProcessor | WARNING: No monitoring data received within the last 60 seconds! Is the monitoring system running?
2021-01-07 16:15:03 |   7084 |                    logStats | -------------- Stats for the last 302 seconds --------------
2021-01-07 16:15:03 |   7084 |                    logStats | Process info:
2021-01-07 16:15:03 |   7084 |                    logStats | modpd is running: 0d 0h 5m 2s
2021-01-07 16:15:03 |   7084 |                    logStats |
2021-01-07 16:15:03 |   7084 |                    logStats | Processed jobs:
2021-01-07 16:15:03 |   7084 |                    logStats | Total processed jobs: '50'
2021-01-07 16:15:03 |   7084 |                    logStats | Successful processed jobs: '50'
2021-01-07 16:15:03 |   7084 |                    logStats | Unsuccessful processed jobs: '0'
2021-01-07 16:15:03 |   7084 |                    logStats | Timed out jobs: '0'
2021-01-07 16:15:03 |   7084 |                    logStats |
2021-01-07 16:15:03 |   7084 |                    logStats | Retransmission jobs:
2021-01-07 16:15:03 |   7084 |                    logStats | Total retransmission jobs: '0'
2021-01-07 16:15:03 |   7084 |                    logStats | Successful retransmission jobs: '0'
2021-01-07 16:15:03 |   7084 |                    logStats | Unsuccessful retransmission jobs: '0'
2021-01-07 16:15:03 |   7084 |                    logStats | Timed out retransmission jobs: '0'
2021-01-07 16:15:03 |   7084 |                    logStats |
2021-01-07 16:15:03 |   7084 |                    logStats | Handled checks:
2021-01-07 16:15:03 |   7084 |                    logStats | Host checks: '7106'
2021-01-07 16:15:03 |   7084 |                    logStats | Service checks: '4202'
2021-01-07 16:15:03 |   7084 |                    logStats | Invalid datasets received: '0'
2021-01-07 16:15:03 |   7084 |                    logStats |
2021-01-07 16:15:03 |   7084 |             debugLogHandler | WARNING: Debug log enabled! This is not intended for use in a production environment!
2021-01-07 16:15:31 |   7084 |               signalHandler | Caught: 'SIGTERM', preparing for shutdown...
2021-01-07 16:15:31 |   7084 |                    logStats | -------------- Stats for the last 28 seconds --------------
2021-01-07 16:15:31 |   7084 |                    logStats | Process info:
2021-01-07 16:15:31 |   7084 |                    logStats | modpd is running: 0d 0h 5m 30s
2021-01-07 16:15:31 |   7084 |                    logStats |
2021-01-07 16:15:31 |   7084 |                    logStats | Processed jobs:
2021-01-07 16:15:31 |   7084 |                    logStats | Total processed jobs: '7'
2021-01-07 16:15:31 |   7084 |                    logStats | Successful processed jobs: '7'
2021-01-07 16:15:31 |   7084 |                    logStats | Unsuccessful processed jobs: '0'
2021-01-07 16:15:31 |   7084 |                    logStats | Timed out jobs: '0'
2021-01-07 16:15:31 |   7084 |                    logStats |
2021-01-07 16:15:31 |   7084 |                    logStats | Retransmission jobs:
2021-01-07 16:15:31 |   7084 |                    logStats | Total retransmission jobs: '0'
2021-01-07 16:15:31 |   7084 |                    logStats | Successful retransmission jobs: '0'
2021-01-07 16:15:31 |   7084 |                    logStats | Unsuccessful retransmission jobs: '0'
2021-01-07 16:15:31 |   7084 |                    logStats | Timed out retransmission jobs: '0'
2021-01-07 16:15:31 |   7084 |                    logStats |
2021-01-07 16:15:31 |   7084 |                    logStats | Handled checks:
2021-01-07 16:15:31 |   7084 |                    logStats | Host checks: '719'
2021-01-07 16:15:31 |   7084 |                    logStats | Service checks: '750'
2021-01-07 16:15:31 |   7084 |                    logStats | Invalid datasets received: '0'
2021-01-07 16:15:31 |   7084 |                    logStats |
2021-01-07 16:15:31 |   7084 |               signalHandler | Caught: 'EXIT', shutting down...
2021-01-07 16:15:31 |   7084 |              checkNamedPipe | Check if named pipe: '/var/lib/modpd/rw/modpd.cmd' exists and if it is read/writeable...
2021-01-07 16:15:31 |   7084 |              checkNamedPipe | Named pipe exists and it is read/writeable
2021-01-07 16:15:31 |   7084 |             removeNamedPipe | Remove named pipe...
2021-01-07 16:15:31 |   7084 |             removeNamedPipe | Removing named pipe was successful
2021-01-07 16:15:31 |   7084 |                   checkLock | Check if lock file: '/var/lib/modpd/lock/modpd.lock' exists and if it is read and writeable...
2021-01-07 16:15:31 |   7084 |                   checkLock | Lock file exists and it is read/writeable
2021-01-07 16:15:31 |   7084 |                  removeLock | Removing lock...
2021-01-07 16:15:31 |   7084 |                  removeLock | Removing lock was successful
2021-01-07 16:15:31 |   7084 |               signalHandler | Exitcode: '143'
2021-01-07 16:15:31 |   7084 |               signalHandler | modpd was running: 0d 0h 5m 30s
2021-01-07 16:15:31 |   7084 |               signalHandler | Bye, bye...

modpd NEB module log snippet

[1607849563] modpd: Copyright © 2017-NOW Christian Zettel (ccztux), all rights reserved, Version: 3.0.0
[1607849563] modpd: Starting...
[1607849563] Event broker module '/usr/lib64/modpd/modpd_naemon.o' initialized successfully.
[1607849863] modpd: The modpd NEB module is running 0d 0h 5m 0s
[1607849863] modpd: *** Stats of processed checks for the last 300 seconds: Hosts: 9941 (OK: 9941/NOK: 0), Services: 7127 (OK: 7077/NOK: 50) ***
[1607850163] modpd: The modpd NEB module is running 0d 0h 10m 0s
[1607850163] modpd: *** Stats of processed checks for the last 300 seconds: Hosts: 10276 (OK: 10276/NOK: 0), Services: 7553 (OK: 7553/NOK: 0) ***
[1607850463] modpd: The modpd NEB module is running 0d 0h 15m 0s
[1607850463] modpd: *** Stats of processed checks for the last 300 seconds: Hosts: 9684 (OK: 9684/NOK: 0), Services: 7452 (OK: 7452/NOK: 0) ***
[1607850763] modpd: The modpd NEB module is running 0d 0h 20m 0s

Backup your modpd installation

Make a backup of your existing installation:

tar -cvzf modpd.bak_$(date +%s).tar.gz /etc/logrotate.d/modpd \
                                       /etc/modpd/ \
                                       /etc/sysconfig/modpd \
                                       /usr/bin/modpd \
                                       /usr/lib/systemd/system/modpd.service \
                                       /usr/lib64/modpd/ \
                                       /var/lib/modpd/ \
                                       /var/log/modpd/

Upgrading modpd from 2.x.x to 3.x.x

Backup your modpd installation

Make a backup of your existing installation:

tar -cvzf modpd.bak_$(date +%s).tar.gz /etc/init.d/modpd \
                                       /etc/logrotate.d/modpd \
                                       /etc/sysconfig/modpd \
                                       /usr/local/modpd/ \
                                       /usr/local/nagios/include/modpd.o

Remove the old installation

Stop the modpd daemon

service modpd stop

Remove the files

chkconfig --del modpd
rm /etc/init.d/modpd
rm /etc/logrotate.d/modpd
rm /etc/sysconfig/modpd
rm -rf /usr/local/modpd/
rm /usr/local/nagios/include/modpd.o

Remove the NEB module from Nagios®

Remove the modpd NEB module with the editor of your choice to your Nagios® main config file:

(Default Nagios® main config file: /usr/local/nagios/etc/nagios.cfg)

broker_module=/usr/local/nagios/include/modpd.o

Restart Nagios®

service nagios restart

Install modpd 3.x.x

Use the regular install guide and merge possible changes between the new config and the old one from your backup using the tool of your choice like vimdiff.