chinezbrun/pytes_serial

Issues

• FEATURE REQUEST: PACK CYCLES

  #39 opened 5 months ago by networkerict
  2

• Feature request - state of health

  #36 opened 5 months ago by andi-at-1
  6

• Configurable parameters in cells monitoring mode

  #38 opened 5 months ago by chinezbrun
  0

• Automatic detection for some config parameters

  #37 opened 5 months ago by chinezbrun
  1

• System sensors became 'unknown' after Home Assistant restart

  #34 opened 8 months ago by chinezbrun
  0

• some terminal output improvents

  #35 opened 8 months ago by stenis25856
  2

• Incorrect logging result

  #33 opened 8 months ago by chinezbrun
  1

• Optimize MQTT publish

  #31 opened a year ago by chinezbrun
  0

• MQTT to many data in the payload message

  #28 opened a year ago by chinezbrun
  1

• With the Pylontech US2000C the cell values are not read out.

  #26 opened a year ago by 001Tycoon
  5

• Cells statistics [min, max, delta...]

  #25 opened a year ago by chinezbrun
  0

• Parsing of single cell values ('bat [index]')

  #24 opened a year ago by chinezbrun
  0

• reported 100% CPU when running

  #23 opened a year ago by Banana5kin
  1

• Cells monitoring: Cells data could not be read - error message

  #22 opened a year ago by chinezbrun
  0

• Multiple pytes serial scrips with one HA

  #20 opened a year ago by chinezbrun
  1

• Sensors name displayed with device name (Home Assistant 2023.08>)

  #21 opened a year ago by chinezbrun
  0

• SOC reported with two decimals in log file

  #19 opened a year ago by chinezbrun
  0

• events to be human readable

  #17 opened 2 years ago by chinezbrun
  1

• monitor cell data when a warning events pop up

  #18 opened 2 years ago by chinezbrun
  0

• event log not limited in size

  #16 opened 2 years ago by chinezbrun
  0

• MQTT discovery -- device info

  #8 opened 2 years ago by chinezbrun
  1

• reading frequency do not have lower limit

  #15 opened 2 years ago by chinezbrun
  1

• Home assistant: history not displayed for all Pytes sensors

  #14 opened 2 years ago by chinezbrun
  0

• forever loop if no data received

  #12 opened 2 years ago by chinezbrun
  1

• Home Assistant warning: incorect unit of measure for voltage

  #13 opened 2 years ago by chinezbrun
  0

• potential mix-up of data set -- doubled data set of battery 1 to others

  #11 opened 2 years ago by chinezbrun
  0

• authentication for mqtt home assistant

  #7 opened 2 years ago by hurly85
  8

• slow recover after parse error

  #3 opened 2 years ago by chinezbrun
  2

• have summary information when multiple batteries are used

  #10 opened 2 years ago by chinezbrun
  0

• parsing error with Pytes model C

  #9 opened 2 years ago by chinezbrun
  0

• Discovered MQTT entities not available after restart HA

  #6 opened 2 years ago by chinezbrun
  0

• error when more than one battery is set

  #4 opened 2 years ago by chinezbrun
  0

• duplicate error in MariaDB

  #5 opened 2 years ago by chinezbrun
  0

• activate MQTT

  #1 opened 2 years ago by chinezbrun
  1

• wrong calculation of negative current

  #2 opened 2 years ago by chinezbrun
  0