clough42/electronic-leadscrew

Issues

• Max spindle encoder value.

  #292 opened 3 months ago by bogus105
  3

• Code Composer v12

  #291 opened 3 months ago by kmanuele
  5

• ELS is great but want to make some very simple code mods

  #288 opened 5 months ago by SteveMaxPerry
  10

• Slower feed rate?

  #282 opened 3 months ago by javaduke
  2

• On-the-fly Encoder Selection, Using DRO Scale encoder output...

  #289 opened 5 months ago by SteveMaxPerry
  3

• Different signal for leadscrew?

  #287 opened 7 months ago by Nabe1234
  0

• Panel doesn't light up

  #286 opened 7 months ago by John5431
  4

• Please help!!! My servo Nema34 jumping, not work softly

  #284 opened 7 months ago by Olazas
  5

• Encoder requires ELS FWD/REV button push to change stepper rotation.

  #281 opened 8 months ago by MMCCLENAHEN
  5

• Key&LED only works with USB power to launchpad

  #280 opened 9 months ago by Bahr01
  5

• Encoder Test Input - solved

  #285 opened 9 months ago by u2fletch
  1

• Please help with Length Display Cable

  #283 opened 9 months ago by Olazas
  3

• SOS Reset sometimes

  #279 opened 10 months ago by Olazas
  5

• Spindle position display option

  #278 opened a year ago by R-Ronald
  35

• Loading Code on Windows 11

  #275 opened a year ago by Cmbart
  1

• Launchpad failure

  #277 opened a year ago by mattdifelice
  5

• Control panel box/enclosure

  #276 opened a year ago by pbrubaker
  3

• Modules and diametral pitches

  #267 opened a year ago by johnsonm
  3

• 2 years of on and off trying to get this to work

  #274 opened a year ago by markcurington
  6

• Feed v thread

  #273 opened a year ago by John5431
  9

• firmware please help

  #260 opened 2 years ago by freddygino
  35

• Servo size?

  #272 opened a year ago by tomvikse
  1

• 2 Phase vs 3 Phase closed loop steppers

  #271 opened a year ago by fenrirza
  0

• Driver wiring

  #269 opened a year ago by Thyerhazard
  2

• Power feed is rough?

  #265 opened a year ago by javaduke
  10

• Flickering screen

  #266 opened a year ago by Thyerhazard
  7

• Carriage stop/emergency switch?

  #268 opened a year ago by javaduke
  8

• Installation on Jet GH1340 - separate threading and feed screws

  #262 opened a year ago by patl1
  18

• threads not cutting what i set to

  #264 opened a year ago by freddygino
  0

• control panel fwd

  #263 opened a year ago by freddygino
  4

• Inaccurate thread pitch

  #259 opened a year ago by oldedwardian
  3

• Powering off the stepper motor while spindle is turning

  #261 opened 2 years ago by ibonneau
  5

• En/Dir issue

  #258 opened 2 years ago by jballard86
  0

• DRO posibities?

  #257 opened 2 years ago by blackfister
  0

• No torque

  #256 opened 2 years ago by Karlofthecounty
  1

• Boost board provided without flash chip

  #252 opened 2 years ago by johnsonm
  6

• Thread table calculation limitations

  #254 opened 2 years ago by johnsonm
  3

• Supporting different Z and X feed rates

  #253 opened 2 years ago by johnsonm
  0

• Error: Program "make" not found in PATH

  #251 opened 2 years ago by voidXEMON
  4

• 36 vs 48 volt power supply?

  #248 opened 2 years ago by javaduke
  4

• Encoder not talking to servo controller flickers

  #246 opened 2 years ago by deirpo
  13

• Problems with power feed

  #249 opened 2 years ago by javaduke
  12

• PM-1130 - feed shaft configuration?

  #247 opened 2 years ago by javaduke
  7

• Suggestion: Manual Jog/Stepping

  #245 opened 2 years ago by Grauenwolf
  7

• iSV57T-180 gearing

  #244 opened 2 years ago by tzarkyl
  1

• How to code for startup in "Power Off"

  #243 opened 2 years ago by Howard-001
  2

• No RPM displayed, 5vdc pulses present, tried both encoder inputs

  #242 opened 2 years ago by oracleglassarts
  6

• Alter feed speed by 50 percent

  #241 opened 2 years ago by Aditchf
  22

• Need help debugging - spinning encoder does nothing to Stepper

  #240 opened 2 years ago by bgrimwade
  11

• Resolving encoder not working with 5 volt supply

  #239 opened 2 years ago by dlmock99
  2