/esp32-bluetooth-bridge

ESP32 Bluetooth to UART Bridge (Replaces HC-05)

Primary LanguageC++

ESP32 Bluetooth Bridge (Replaces HC-05)

Do you have a project where you'd like it to be possible for you to connect to (and potentially reprogram) another microcontroller over Bluetooth, but also want to have the flexibility to add new Bluetooth, BLE, or WIFI features? I previously used the HC-05 bluetooth module for providing Bluetooth tty access for interactions and programming; the ESP32, though, is only slightly more expensive and provides many features that the HC-05 cannot offer -- including that it itself can be programmed over-the-air to add your own features and functionality very easily.

This repository contains a simple Bluetooth-to-UART bridge roughly mirroring how the HC-05 behaved, but adds a handful of new features:

  • An escape sequence allowing you to break out of your serial bridge to send commands to the wireless unit itself directly.
  • The ability to accept commands including one allowing you to monitor the bluetooth bridge via the ESP32's UART1.
  • Configurable pin connections for:
    • Indicating when a client is connected over bluetooth (PIN_CONNECTED)
    • Allowing the bridged microcontroller to send commands directly to the ESP32 (BT_KEY).
    • Connecting to the Microcontroller's reset line for debugging, flashing, and troubleshooting.
    • RX/TX output pins for connecting to the microcontroller.
  • A variety of (partially STM32-specific) commands and the ability for you to add your own very easily.

Commands

flash_esp32

This command begins an OTA flash of the ESP32 unit itself. In general, there is no need for you to run this command directly, instead use the included python script in programming/ota_flash.py to flash the ESP32 unit over bluetooth. See "Flashing the ESP32 Over-the-air" for details.

flash_uc

This command is designed to reboot an STM32 microcontroller into its serial bootloader by:

  • Pulling its BOOT0 pin high (see PIN_CONNECTED in main.h)
  • Pulling its nRST line low for 250ms (see UC_NRST in main.h)
  • Pulling its nRST line high

At that point, the microcontroller will be ready to accept programming over bluetooth.

reset_uc

Briefly pulls the microcontroller's reset line low to cause it to restart.

boot0 [0|1]

  • When called without an argument: returns the current state of the BOOT0 pin (i.e. PIN_CONNECTED).
  • When called with an argument of 0: Pulls BOOT0 (PIN_CONNECTED) low.
  • When called with an argument of 1: Pulls BOOT0 (PIN_CONNECTED) high.

PIN_CONNECTED is generally connected directly to the BOOT0 pin of the microcontroller to emulate the procedure historically used for using an HC-05 unit to flash an STM32 microcontroller. You'll notice that they are used interchangably throughout this document and in the source, but do know that you can adjust the state of this pin independently from its default behavior of indicating whether a client is connected.

monitor [0|1]

  • When called without an argument: returns the current state of the serial monitor.
  • When called with an argument of 0: Turns serial monitoring off.
  • When called with an argument of 1: Turns serial monitoring on.

Note that this is probably only useful if you are issuing commands to the ESP32 unit's UART1 instead of communicating over Bluetooth.

nrst [0|1]

  • When called without an argument: stops setting the state of the microcontroller's nRST pin by reconfiguring the corresponding ESP32 pin as an input.
  • When called with an argument of 0: Pulls nRST (UC_NRST) low.
  • When called with an argument of 1: Pulls nRST (UC_NRST) high.

unescape

Exits "escaped" mode if the device had previously recieved the relevant escape sequence. This is useful for allowing you to re-enable pass-through functionality after issuing an escape sequence to send your microcontroller a command.

Building the firmware

First, make sure that you have installed the xtensa compiler (xtensa-esp32-elf-gcc) and that it is available on your PATH.

Next, make sure you've cloned all necessary submodules:

git submodule update --init --recursive

After that, set the IDF_PATH environment variable to point at your clone of the esp32 IDF (https://github.com/espressif/esp-idf) -- and make sure that you've checked out a commit that is compatible with the version of arduino-esp32 in use. If you're running this repository as it is now, that commit should be aaf12390.

Now, just ask it to compile:

make

You're now ready to flash that firmware onto the device. Note that if you are flashing over the air, you should follow the procedure described below under "Flashing the ESP32 Over-the-air" instead of following the usual make flash procedure.

Escape Sequence

Default: CTRL+D, CTRL+D, CTRL+D, !

The escape sequence keys must be pressed at least 500ms apart from one another (and, obviously, no other keys may be pressed between each of your escape sequence bytes). This might sound a little strange, but this behavior exists as a way of making sure that the bytes transmitted as part of your escape sequence aren't occurring naturally as part of some other data you're intentionally transmitting to your microcontroller.

If you want to make adjustments to this behavior, see:

  • main.h: BT_CTRL_ESCAPE_SEQUENCE_INTERCHARACTER_DELAY to adjust the minimum amount of time that must pass between each character of your escape sequence.
  • main.cpp; BT_CTRL_ESCAPE_SEQUENCE to adjust the escape sequence itself.

Flashing the ESP32 Over-the-air

It's possible to flash the ESP32 unit itself over blueotooth by using the included python script (programming/ota_flash.py); to do that, follow the instructions below.

Note that flashing is essentially 100% safe for an ESP32 module; the device's built-in Over-the-air programming functionality is cleverly designed and will not switch to the newly-programmed source unless it passes a verification procedure. If the flashing process fails for any reason, the installed code will remain unchanged.

Building the firmware

See "Building the firmware".

Installing Dependencies

From your clone of this repository, run the following commands:

cd programming
virtualenv . --python=python3
source bin/activate
pip install -r requirements.txt
cd ..

Flashing the firmware

From your clone of this repository, run the following commands:

cd programming
python ota_flash.py /path/to/bluetooth/device

By default, this will:

  • Connect to the device you have specified (at which point, you will be connected via the pass-through to the connected microcontroller).
  • Sends the "Escape Sequence" mentioned above to escape the pass-through.
  • Issues the command flash_esp32.
  • Waits for the ESP32 unit to be ready.
  • Sends the new firmware stored in ../build/bridge.bin.
  • Prints any messages received from the ESP32 unit during this process.

At the end of this process, you should see one of the following messages:

  • <completed: success>: If the flashing process completed successfully.
  • <completed: failure>: If the flashing process failed for some reason. Consult the other displayed messages to determine a potential cause for this flashing fialure. Note that failures are completely safe, and you can try re-flashing again as soon as you'd like.

See python ota_flash.py --help for other options.