/LePi

LePi is a lightweight library for FLIR Lepton (2, 2.5 and 3) and Raspberry pi.

Primary LanguageCMIT LicenseMIT

LePi [lee-pahy]

Copyright (c) 2017 Andrei Claudiu Cosma

LePi is a lightweight library for FLIR Lepton (2, 2.5 and 3) and Raspberry Pi. The Lepton version will be automatically detected at run time. The SPI port can be specified in the app, by default the LePi apps are using SPI0.

Please make sure that the sensor is properly wired. Here is an example for Rapberry Pi2:

  • SCL -> Pin#5, SDA -> Pin#3, VIN -> Pin#1, GND -> Pin#25, CLK -> Pin#23, MISO -> Pin#21, MOSI -> Pin#19, CS -> Pin#24 Lepton-Raspberry Pi wiring

Code Examples

LePi offers 2 easy to use interfaces for accessing the Lepton frames. First interface is the serial interface, this reads the frame from sensor when frame is requested:

LePi lePi;
lePi.OpenConnection();

std::vector<uint8_t> frame(120 * 180);
lePi.GetFrame(frame.data(), FRAME_U8);

lePi.CloseConnection();

The second available interface, it is the parallel interface which allows the user to read the latest frame grabbed from the sensor. The interface grabs all available frames from the sensor and it offers access to the latest one. This should be the prefered option, since it stays in sync with the Lepton sensor and it makes sure that it reads all available frames.

LeptonCamera cam;
cam.start();

std::vector<uint8_t> frame(120 * 180);
if (cam.hasFrame()) {
    cam.getFrameU8(frame);
}

cam.stop();

For a more in depth example on how to use this library please check the available apps.

Dependecies

  • [REQUIRED] CMake:
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install build-essential cmake pkg-config

tar zxvf bcm2835-1.52.tar.gz
cd bcm2835-1.52
./configure
make
sudo make check
sudo make install

You can follow these steps for installation https://www.pyimagesearch.com/2016/04/18/install-guide-raspberry-pi-3-raspbian-jessie-opencv-3/, or other tutorial that you find useful and easy to follow. I'm using OpenCV 3.3.0, but any version after 3.0.0 should be okay.

Note: The library can be built without OpenCV. In that case, the demo apps will not be available. Also, I'm planning on writing an example that uses the librarry without OpenCV.

Build

LePi build is based on the CMake portable pre-build tool. Follow the next steps to build the library and the apps:

git clone https://github.com/cosmac/LePi.git
cd LePi
mkdir build
cd build
cmake ..
make

Run

LePi library comes with a set of integrated demo apps, that shows how to use the Lepton camera serial and parallel interface. Once the library is build, demo apps can be found in the install/bin folder. To run a demo app:

cd LePi/install/bin
sudo ./Player

Note1: sudo is always required when you run an app communicating with the Lepton sensor

Note2: You may observe different frame rates between Letpon 2 and 3. That is because the library reads all the frames available on the SPI port! Based on the Lepton 2 datasheet you can observe that since the real frame rate is ~9 fps, they send the same frame 3 times until the next frame is available. Now, for Lepton 3, they decided to send discard packets until a new frame is avialble. For this reason you may see a frame rate of ~26 fps for Lepton 2 and ~9 fps for Lepton 3. Anyway, in both cases, there are only ~9 unique frames per second.

Other resources