disk-burnin.sh is a bash shell script I wrote to simplify the process of burning-in disks. It is intended for use only on disks which do not contain data, such as new disks or disks which are being tested or re-purposed. I was inspired by the "How To: Hard Drive Burn-In Testing" thread on the TrueNAS forum and I want to give full props to the good folks who contributed to that thread.
Be aware that:
- This script runs the
badblocksprogram in destructive mode, which erases any data on the disk. Therefore, please be careful! Do not run this script on disks containing data you value! - It is best to run this on disks that are not part of a pool or mounted in any manner.
- Run times for large disks can take several days to complete on small disks and a week or more for large disks, so it is a good idea to use tmux sessions (using the
-mswitch) to prevent mishaps. - Must be run as 'root'.
Performs these steps:
- Run SMART short test
- Run SMART conveyance test
- Run SMART extended test
- Run
badblocks† - Run SMART short test †
- Run SMART conveyance test †
- Run SMART extended test †
† These test are not run for SSDs as badblocks will only reduce the lifespan of the drive to no useful purpose.
The script sleeps after starting each SMART test, using a duration based on the polling interval reported by the disk, and adding an additional delay to account for discrepancies.
Full SMART information is pulled after each SMART test. All output except for the sleep command is echoed to both the screen and log file.
You should periodically monitor the burn-in progress and check for errors, particularly any errors reported by badblocks, or these SMART errors:
| ID | Attribute Name |
|---|---|
| 5 | Reallocated_Sector_Ct |
| 196 | Reallocated_Event_Count |
| 197 | Current_Pending_Sector |
| 198 | Offline_Uncorrectable |
These indicate possible problems with the drive. You therefore may wish to abort the remaining tests and proceed with an RMA exchange for new drives or discard old ones. Also please note that this list is not exhaustive.
The script extracts the drive model and serial number and creates a log filename of the form burnin-[model]_[serial number]-[date].log.
badblocks is invoked with a block size of 4096, the -wsv options, and the -o option to instruct it to write the list of bad blocks found (if any) to a file named burnin-[model]_[serial number]-[date].bb.
The only required command-line argument is the device specifier, e.g.:
./disk-burnin.sh -d ada0
...will run the burn-in test in 'dry run mode' on device /dev/ada0
If you are not sure of the device specifiers currently on the system you can get a list with the -L switch.
./disk-burnin.sh -L
You can run the script in 'dry run mode' to check the sleep duration calculations and to insure that the sequence of commands suits your needs. In 'dry runs' the script does not actually perform any SMART tests or invoke the sleep or badblocks programs. The script is distributed with 'dry runs' enabled, so you will need to pass the -t switch, in order to actually perform tests on drives.
The script can automatically invoke tmux sessions for a space separated list of drive specifiers:
./disk-burnin.sh -tm 'ada0 da0 ada1 da0'
Additionally using the -l switch you can specify the location where you would like the logs written.
Tested on these drives:
- Intel DC S3700 SSD
- Intel Model 320 Series SSD
- HGST Deskstar NAS (HDN724040ALE640)
- Hitachi/HGST Ultrastar 7K4000 (HUS724020ALE640)
- Western Digital Re (WD4000FYYZ)
- Western Digital Black (WD6001FZWX)
Requires the smartmontools, available at https://www.smartmontools.org
Uses: grep, pcregrep, awk, sed, tr, sleep, badblocks
Tested with the static analysis tool at https://www.shellcheck.net to insure that the code is free of issues.
Written by Keith Nash, March 2017. Modified by Yifan Liao and dak180.