DaikinEthernet

Daikin ARC remote control for arduino with ethershield and include DHT11 sensor.

Daikin ARC 遠端控制使用Arduino配合ethershield完成網路控制Daikin

Circuit

Picture

Prepare

first,you need to know how to install arduino library and finish this librarys:

首先，你必需要學會如何自行安裝函數庫，完成下列的安裝：

Download and Run

Download DaikinEthernet source code and unzip it.next, you can open the DaikinEthernet.ino .

下載 DaikinEthernet 源始碼並且解壓後開啟它

Modify Network IP

modify the ip in your network enverment. make sure your network can be used.

根據你的網路環境來修改你的IP，並且確認你的網路環境是可運作的。

if your network need to connect internet,you must fix Network Mask、Gateway setting

如果你要連外網路的話必需要填入Network Mask、Gateway

find 尋找

IPAddress ip(192, 168, 9, 59);

// Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);

replace 覆蓋

IPAddress ip(192, 168, 9, 59);
IPAddress gateway(192, 168, 9, 1);
IPAddress networkmask(255, 255, 255, 0);

find 尋找

  //ethernet shield init
  Ethernet.begin(mac, ip);
  Serial.println(Ethernet.localIP());
  server.begin();

  //ethernet shield init
  Ethernet.begin(mac, ip, gateway, networkmask);
  Serial.println(Ethernet.localIP());
  server.begin();

Upload to Arduino

connect arduino to pc by usb cable. click upload button to flash code to arduino.

利用USB將你的Arduino連接並且按下上傳鍵將程式上傳至Arduino

Command/Format 命令與格式

format 格式

http://your ip/action[get|set][number][value] http://你的位址/動作[取|存][號碼][值]

action 動作

action is device like sensor,daikin ac...etc.

get/set 取//存

get is ?,set is =

取值為問號?，存值為=

number 號碼

number can support same type of devices,but it is reserve and value is 00.

號碼為了將來能支援同類型的裝置而準備，目前功能未完成，預設值以00

value 值

value is two digital ascii number a group.ex: 1 is 01.

值為兩位數的字串型數值，像數值1則以01表示

example 範例

http://192.168.9.59/ft?00

check your arduino feature and response like:

檢查你的arduino支援功能的請求，得到的結果如下：

{"status":"ok","version":"1","ac":"1,"humidity":"1","temperature":"1"}

command 命令

number is reserve and value is 00

getter 取值命令

ft?00

get feature 取得支援功能

{"status":"ok","version":"1","ac":"1,"humidity":"1","temperature":"1"}

hm?00

get humidity 取得溼度

{"status":"ok","number":"0","humidity":"32.00"}

tp?00

get temperature 取得溫度

{"status":"ok","number":"0","temperature":"25.00"}

ac?00

get air condition state 取得空調的狀態

{"status":"ok","number":"0","power":"0","swing":"0","mode":"0","speed":"0","temperature":"25"}

setter 存值命令

ac=[00][power][swing][mode][speed][temperature]

set air condition state 設定空調的狀態

power 電源

0: off 1: on

swing 擺動

0:off 1:on

mode 模式

0:FAN 1:COOL 2:DRY

speed 速度

0:speed 1 1:speed 2 2:speed 3 3:speed 4 4:speed 5 5:Auto 6:moon

temperature 溫度

18 ~ 33 degree.

example

 curl http://192.168.9.59/ac=000000010625

response

{"status":"ok"}

if it have any error ,response:

{"status":"command error"}

danny-source/DaikinEthernet