Xiaomi Mijia LYWSD03MMC HW: B1.4, B1.6, B1.7, B1.9, B2.0 & Xiaomi Miaomiaoce MHO-C401 & CGG1 Mijia Bluetooth Thermometer Firmware & CGDK2 Qingping Temp & RH Monitor Lite

This repository contains custom firmware for several Bluetooth Thermometer & Hygrometer devices. The download of the appropriate firmware for your device will be presented automatically in TelinkMiFlasher.html. Downloading files from this repository is not required. Alternative firmware and configurator from ATC1441 (variant ATC_Thermometer.bin) can be found here: atc1441/ATC_MiThermometer. Custom firmware is not supported in MiHome. But it is possible to work LYWSD03MMC with 'Xiaomi Gateway 3' by first registering in MiHome on the official firmware, flashing to custom firmware with restoring the binding key from MiHome, replacing the device name with "LYWSD03MMC" and setting the advertising type to "MIJIA (MiHome)" marked "encrypted".

The custom firmware can be flashed via a modern browser and over-the-air (OTA) without opening the device and unlocks several customization options. You can go back to the original firmware at any time. OTA and configuration main page - TelinkMiFlasher.html.

Key features

Extended battery life (over a year)
Improved measurement accuracy and extended format in 0.01 units
Full support Home Assistant 'Passive BLE Monitor integration' and 'HA BLE DIY' beacon format
Supports encrypted connections using PIN-code and encrypted bindkey beacon
Support Bluetooth5.0+ PHY (1 and 2 Mbps), CSA1/CSA2 (Channel Selection Algorithm)
3 LCD Display Screens (Looping): Temperature & Humidity & Comfort, Temperature & Battery Level, Clock
Measurement values recording & Charting. See Reading Measurements from Flash
Adjustable correction offsets and Comfort zones
Support for 4 beacon formats: Xiaomi, ATC, Custom, HA-BLE and encrypted options.
Adjustable RF TX Power & Bluetooth advertising interval
DIY improvements - relay control by temperature or humidity, transmission of the reed switch status - open / closed or pulse counter

Xiaomi Mijia (LYWSD03MMC)	Xiaomi Miaomiaoce (MHO-C401)	Qingping Temp & RH Monitor (CGG1-Mijia)	CGDK2 Qingping Temp & RH Monitor Lite

Table of content

Getting Started
- Flashing or Updating the Firmware (OTA)
- Configuration
Firmware
- Firmware Binaries
- Firmware version history
Applications
Technical specifications
Related Work
Resources & Links
- CJMCU-2557 BQ25570

Getting Started

You can conveniently flash, update and configure the bluetooth thermometers remotely using a bluetooth connection and a modern web browser.

Flashing or Updating the Firmware (OTA)

To flash or update the firmware, use a Google Chrome, Microsoft Edge or Opera Browser.

Go to the Over-the-air Webupdater Page TelinkMiFlasher.html *
If using Android, Windows, Linux: Ensure you enabled "experimental web platform features". Therefore copy the according link (i.e. chrome://flags/#enable-experimental-web-platform-features for Chrome), open a new browser tab, paste the copied URL. Now sten the Experimental Web Platform features flag to Enabled. Then restart the browser.
In the Telink Flasher Page: Press Connect: The browser should open a popup with visible Bluetooth devices. Choose the according target device (i.e. LYWSD03MMC) to pair.
After connection is established a Do Acivation button appears. Press this button to start the decryption key process.
Now you can press the Custom Firmware ver x.x button to directly flash the custom firmware. Alternatively you can choose a specific firmware binary (i.e. the original firmware) via the file chooser
Press Start Flashing.

Use TelinkOTA to flash old or alternative versions (ATC1441). This is a program for OTA projects with Telink SDK, no third-party (mijia) protections.

Configuration

After you have flashed the firmware, the device has changed it's bluetooth name to something like ATC_F02AED. Using the TelinkMiFlasher.html you have various configuration options.

General process:

Press Connect
Select the according device to connect/pair (i.e. ATC_F02AED)
Several configuration options appear
Choose Send Config to send changed value to the device. Or press Set default and then Send config to revert to the Defaults

Option	Description
Temperature and Humidity offset	Enter a value to correct the offset of the Temperature or Humidity displayed: For example `-1.4` will decrease the Temperature by 1.4°
Smiley or Comfort	Choose a static smiley or check the "Comfort" Radio box to change the smiley depending on current Temperature and Humidity.
Comfort Parameters	Defines the Lower (Lo) and Upper (Hi) Range for Temperature and Humidity interpreted as comfort zone. In the default configuration a smiley will appear.
Advertising Type	Type of supported Bluetooth Advertising Formats.
Set time	sends the current time to the device
Comfort, Show batt, Clock	Ticking the according boxes you can enable interval rotation between different LCD screens. See the example video below.

Example of LCD display modes

You can configure different LCD Display modes using Comfort, Show batt and Clock configuration checkboxes. The enabled LCD Display Modes will appear one-by-one in a loop.

Battery and clock display are enabled in the settings. The rest of the settings is kept default. The video contains 2 cycles.

Temperature and humidity

Temperature and % of battery

Temperature and humidity

Hours and minutes

Firmware

Firmware Binaries

You can directly update/flash the firmware without downloading the binaries below.

Custom Firmware Versions:

LYWSD03MMC Custom Firmware Version 3.7 (HW: B1.4, B1.6, B1.7, B1.9, B2.0)
MHO-C401 Custom Firmware Version 3.7 (manufacturer Xiaomi, not Azarton!)
CGG1 Custom Firmware Version 3.7 (CGG1-M)
CGDK2 Custom Firmware Version 3.7 (CGDK2)

Original Manufacturer Firmware Version

In case you want to go back to the original firmware, you can download them here:

Firmware version history

Version	Changes
1.2	Bind, Set Pin-code, Support MHO-C401
1.3	Get/Set comfort parameters
1.4	Get/Set device name, Get/Set MAC
1.5	Add Standard Device Information Characteristics
1.6	Fix alternation of Advertising in mi mode
1.7	Authorization and encryption in permissions to access GAP ATT attributes, if pin code is enabled
1.8	Time display (instead of a blinking smile)
1.9	Recording measurements to flash memory (cyclic buffer for 19632 measurements)
2.0	Recording measurements with averaging to flash memory
2.1	Periodic display refresh for MHO-C401 'Erase mi-keys' option to return to original firmware
2.2	Added parameter "Encrypted Mi Beacon"
2.3	Added "Delete all records"
2.4	Added parameter "Clock time step"
2.5	Remove TRG/FLG errors, minor optimization
2.6	Expanding the ranges of threshold parameters (TRG)
2.7	Reducing power consumption of MHO-C401 (EDP update), adding version for CGG1
2.8	Added saving bindkey to EEP if mi-keys are erased, reduced TX power to 0 dB for defaults
2.9	Added additional id flags to advertising packages
3.0	Added toggle support for advertising package structures for third-party software
3.1	Fix security attributes (for pincode)
3.2	Added new encrypted beacon formats, reed switch maintenance
3.3	Added autodetection for LYWSD03MMC hardware versions B1.6 and B1.9. For CGG1-M and MHO-C401 - autodetection of SHTV3 or SHT4x sensors
3.4	Correct Hardware Version Setting for LYWSD03MMC B1.7
3.5	Correction of moisture readings for SHT4x sensors. Rounding off sensor values on display.. Saving HW string B2.0 on LYWSD03MMC. Eliminated battery voltage noise in CGG1-M. CGG1 - correction of the battery charge display. Added CGDK2 and modified (DIY) variant of CGDK2-2.
3.6	Additional parameters: Support BT5.0 PHY, Channel Selection Algorithm 2, Correct RF-TX Power in suspend
3.7	Added format 'HA BLE', reed switch operation mode: Switch and Count
3.7b	Full support for "HA BLE" encryption

Applications

Reading Measurements from Flash

GraphMemo.html

To record the measurement results, a cyclic buffer in the flash memory for 19632 measurements is used. The recording step interval is set in the interface. With the default settings, the recording step is 10 minutes, which gives a recording depth of 4 and a half months. During the step period, the sensor data and battery voltage are averaged, time stamped, and written to flash memory.

Setting the value to 0 disable logging to internal storage.

Reading Measurements in Connected Mode

GraphAtc.html GraphAtc1.html GraphAtc2.html DevPoint.html

Reading Measurements in Advertising Mode

This requires the Experimental Web Platform Features flag enabled in your browser. See Flashing or Updating the Firmware (OTA).

Advertising.html

Technical specifications

Average power consumption

Xiaomi Mijia (LYWSD03MMC)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 10 seconds:

Bluetooth Advertisement: 14..20 uA 3.3V (CR2032 over 6 months)
Bluetooth Connection: 14..25 uA 3.3V (CR2032 over 6 months)

Xiaomi Miaomiaoce (MHO-C401)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 20 seconds:

Bluetooth Advertisement: 12..30 uA 3.3V (depends on the amount of temperature or humidity changes over time to display)
Bluetooth Connection: 15..30 uA 3.3V (depends on the amount of temperature or humidity changes over time to display)

Bluetooth Advertising Formats

The Firmware can be configured to support one of four different Bluetooth advertisements data formats. Supports bindkey beacon encryption.

You can also configure to transferring everything in turn (round-robin)

atc1441 format:

UUID 0x181A - size 16 (temperatyre in 0.1%, humidity in 1%): atc1441 format

Custom format (all data little-endian):

UUID 0x181A - size 19: Custom extended format in 0.01 units (all data little-endian):

uint8_t     size;   // = 19
uint8_t     uid;    // = 0x16, 16-bit UUID
uint16_t    UUID;   // = 0x181A, GATT Service 0x181A Environmental Sensing
uint8_t     MAC[6]; // [0] - lo, .. [6] - hi digits
int16_t     temperature;    // x 0.01 degree
uint16_t    humidity;       // x 0.01 %
uint16_t    battery_mv;     // mV
uint8_t     battery_level;  // 0..100 %
uint8_t     counter;        // measurement count
uint8_t     flags;  // GPIO_TRG pin (marking "reset" on circuit board) flags: 
                    // bit0: Reed Switch, input
                    // bit1: GPIO_TRG pin output value (pull Up/Down)
                    // bit2: Output GPIO_TRG pin is controlled according to the set parameters
                    // bit3: Temperature trigger event
                    // bit4: Humidity trigger event

Encrypted beacon formats (uses bindkey):

Xiaomi Battery Charge

UUID 0xFE95 - 0x0A: Xiaomi - battery charge level 0..100%, battery voltage in mV

Xiaomi Temperature & Humidity

UUID 0xFE95 - 0x0D: Xiaomi - temperature x0.1C, humidity x0.1%

Xiaomi Encrypted (bindkey enable)

UUID 0xFE95 - 0x0A, 0x04, 0x06 Xiaomi - battery charge level 0..100%, temperature x0.1C, humidity x0.1% (All data are averaged over a period of 16 measurements)

Bluetooth Connection Mode

Primary Service - Environmental Sensing Service (0x181A):

Characteristic UUID 0x2A1F - Notify temperature x0.1C
Characteristic UUID 0x2A6E - Notify temperature x0.01C
Characteristic UUID 0x2A6F - Notify about humidity x0.01%

Primary Service - Battery Service (0x180F):

Characteristic UUID 0x2A19 - Notify the battery charge level 0..99%

Primary Service (0x1F10):

Characteristic UUID 0x1F1F - Notify, frame id 0x33 (configuring or making a request): temperature x0.01C, humidity x0.01%, battery charge level 0..100%, battery voltage in mV, GPIO-pin flags and triggers.

Temperature or humidity trigger on GPIO PA5 (label on the "reset" pin)

Xiaomi LYWSD03MMC has a PCB soldering test point. Available without disassembling the case and marked "Reset". Use as a trigger output with adjustable temperature and / or humidity hysteresis. Hysteresis and thresholds are set in TelinkMiFlasher.html. The output status is displayed in the advertising package.

Hysteresis:

=0 off,

if less than zero - activation on decrease,

if more than zero - activation on excess

Setting the pin to "1" or "0" works if both hysteresis are set to zero (TRG off).

Trigger and reed switch status receiver on JDY-10 module ($1).

Reed Switch on GPIO PA6 (label on the "P8" pin)

It is possible to solder a reed switch on the LYWSD03MMC board to the pins marked "P8" and GND. The state of the reed switch is transferred to the advertising package. For CGG1 - GPIO_PD3, MHO_C401 - no free pins.

Interface for receiving and displaying data on the LCD.

LCD shows:

Big number: -99.5..1999.5

Small number: -9..99

Smiley, battery, degrees

Setting the display time limit in sec

The USB-COM adapter writes the firmware in explorer. Web version.

Connect only TX-SWS and GND wires.

USBCOMFlashTx.html

Chipset LYWSD03MMC HW:B1.4

TLSR8251F512ET24 (TLSR8258 in 24-pin TQFN). SoC: TC32 32-bit MCU 48Mhz, 64 KiB SRAM, 512 KiB Flash (GD25LE40C), Bluetooth 5.0: Mesh, 6LoWPAN, Zigbee, RF4CE, HomeKit, Long Range, Operating temperature: -40°C to +85°C, Power supply: 1.8V to 3.6V.

SHTV3 sensor. Measurement range: Temperature -40°C to +125°C, Humidity 0 to 100 %RH. Power supply: 1.8V to 3.6V

IST3055NA0 LCD controller

LYWSD03MMC B1.4 BoardPinout

Building the firmware

Windows:

Go to wiki.telink-semi.cn and get the IDE for TLSR8 Chips.
Install the IDE and import the 'ATC_MiThermometer' project
Compile the project

Ubuntu:

  git clone https://github.com/pvvx/ATC_MiThermometer.git
  cd ATC_MiThermometer
  make

Related Work

ATC_MiThermometer is based on the original work of @atc1441, who developed the initial custom firmware version and the web-based OTA flasher (Source).

Resources & Links

CJMCU-2557 BQ25570

Control function ID when connected

Primary Service UUID 0x1F10, Characteristic UUID 0x1F1F

ID	Command
0x01	Get/Set device name
0x10	Get/Set MAC
0x11	Get/Set Mi key: DevNameID
0x12	Get/Set Mi keys: Token & Bind
0x15	Get all Mi keys
0x16	Restore prev mi token & bindkeys
0x17	Delete all Mi keys
0x18	Get/set binkey in EEP
0x20	Get/Set comfort parameters
0x22	Get/Set show LCD ext.data
0x23	Get/Set Time
0x24	Get/set adjust time clock delta
0x33	Start/Stop notify measures in connection mode
0x35	Read memory measures
0x36	Clear memory measures
0x44	Get/Set TRG config
0x45	Set TRG output pin
0x4A	Get/Set TRG data (not save to Flash)
0x55	Get/Set device config
0x56	Set default device config
0x5A	Get/Set device config (not save to Flash)
0x60	Get/Set LCD buffer
0x61	Start/Stop notify LCD buffer
0x70	Set PinCode
0x71	Request Mtu Size Exchange

dapgo/ATC_MiThermometer