hysen

Home Assistant support for Broadlink Hysen thermostat controllers

Introduction

This repository implements Home Assistant support for Broadlink Hysen thermostat controllers. Eventual goal is to have the main module integrated to the Home Assistant project.

Discussion on the module (and the preceding broadlinkHysen.py module) can be found at https://community.home-assistant.io/t/beta-for-hysen-thermostats-powered-by-broadlink/56267/1 .

Installation

HACS

The easiest way to add this to your Homeassistant installation is using HACS and add this repository as a custom repository.

Manual

THIS CODE ONLY WORK ON VERSION 0.80 AND ABOVE OF HA

Download the hysen directory of files.

As of 0.88 of Home Assistant

Copy the climate.py file into your home-assistant installation 'custom_components/hysen' folder.

(NOTE: for earlier HA versions >=0.80, create directory custom_components/climate, download climate.py into it and rename it to hysen.py.)

Configuration

Add something similar to the following in your configuration.yaml file:

climate:
  - platform: hysen
    devices:
      main_thermostat:
        name: Main Thermostat
        host: 192.168.X.X
        mac: "XX:XX:XX:XX:XX:XX"
      secondary_thermostat:
        name: Secondary Thermostat
        mac: "YY:YY:YY:YY:YY:YY"

NOTE : At the moment, you may have to setup the device Wifi connection with the horrible "Room Heat" app, that was supplied with the device. In test, if you setup the above with no IP and valid mac, e.g. 30:30:30:30:30:30 the service will fail to load the device, but will setup services that can be called to enable you to setup the device wifi properly.

Once it fails in the log follow the To get the hysen thermostat in the mode to allow setting of the Wi-fi parameters. With the device off Press and hold on the“power” button, then press the “time” button Enter to the advanced setting, then press the “auto” button 9 times until “FAC” appears on the display Press the “up” button up to “32”, then Press the “power” key, and the thermostat will be shutdown. Press and hold on the “power” button, then press the “time”, the wifi icon beging flashing WiFi fast flashing show.

From Developer tools in HA select the climate.hysen_config_wifi service enter the JSON {"ssid":"yourssid","password":"yourpassword","sectype":4} Security mode options are (0 - none, 1 = WEP, 2 = WPA1, 3 = WPA2, 4 = WPA1/2) run call service, the wifi icon on the device should stop fast flashing and go stable. In the HA log file you should see "Discovered Broadlink Hysen device : "XX:XX:XX:XX:XX:XX, at 192.xxx.xxx.xxx" In your router find the thermostat and set it to have a fixed IP, then set it up in your HA config file as host: and mac: above

Please read comments in the climate.py file for more information on services to set parameters and schedule of the thermostat.

Setting up template sensors

The thermostat doesn't natively expose any sensors, but many can be set up using Home Assistant templates.

An example follows::

sensor:
- platform: template
   sensors:
    house_thermostat_main_house_temp:
     icon_template: mdi:thermometer-lines
     friendly_name: "House Temperature"
     value_template: |
        "{{states.climate.house_thermostat.attributes.current_temperature}}"
     unit_of_measurement: "°C"
    house_thermostat_heating_state:
     icon_template: mdi:fire
     friendly_name: "Heating Demand"
     value_template: |
        "{% if states.climate.house_thermostat.attributes.heating_active == 1 %}On{% else %}Off{% endif %}"
    house_thermostat_auto_override:
     icon_template: mdi:flash-outline
     friendly_name: "Auto Override"
     value_template: "{% if states.climate.house_thermostat.attributes.auto_override == 1 %}On{% else %}Off{% endif %}"
    house_thermostat_externalsensortemp:
     icon_template: mdi:thermometer-lines
     friendly_name: "External Sensor Temp"
     value_template: "{{states.climate.house_thermostat.attributes.external_temp}}"
     unit_of_measurement: "°C"

Setting up template switches

Like sensors, device configuration attributes can be exposed via templates::

  switch:
  - platform: template
     switches:
       thermostat_remote_lock:
          friendly_name: Keypad Lock
          value_template: "{{ is_state_attr('climate.house_thermostat', 'remote_lock', 1) }}"
          turn_on:
            service: climate.hysen_set_remotelock
            data:
              entity_id: climate.house_thermostat
              remotelock: 1
          turn_off:
            service: climate.hysen_set_remotelock
            data:
              entity_id: climate.house_thermostat
              remotelock: 0

darz82/hysen