/ocp4-helpernode

This playbook helps set up an "all-in-one" node, that has all the infrastructure/services in order to install OpenShift 4.

Primary LanguageShell

OCP4 Helper Node

❗ Red Hat support cannot assist with problems with this Repo. For issues please open a GitHub issue

This playbook helps set up an "all-in-one" node, that has all the infrastructure/services in order to install OpenShift 4. After you run the playbook, you'll be ready to begin the installation process.

A lot of OpenShift 4 specifc jargon is used throughout this doc, so please visit the official documentation page to get familiar with OpenShift 4.

⚠️ This playbook originally was written with BareMetal UPI install in mind

This playbook assumes the following:

  1. You're on a Network that has access to the internet.
  2. The network you're on does NOT have DHCP (you can disable installing DHCP on the helper).
  3. The ocp4-helpernode will be your LB/DHCP/PXE/DNS and HTTP server.
  4. You still have to do the OpenShift Install steps by hand.
  5. I used CentOS 7/8, but RHEL 7/8 will work as well.
  6. You will be running the openshift-install command from the ocp4-helpernode.

Below is a highlevel diagram how the ocp4-helpernode fits into your network.

ocp4-helpernode

It's important to note that you can delegate DNS to this ocp4-helpernode if you don't want to use it as your main DNS server. You will have to delegate $CLUSTERID.$DOMAIN to this helper node.

For example; if you want a $CLUSTERID of ocp4, and you have a $DOMAIN of example.com. Then you will delegate ocp4.example.com to this ocp4-helpernode.

Using this playbook

The following are highlevel steps on how to use this playbook. There are more detailed instructions in the "quickstarts" section.

Prereqs

⚠️ NOTE If using RHEL 7, you will need to enable the rhel-7-server-rpms and the rhel-7-server-extras-rpms repos. If you're using RHEL 8, you will need to enable rhel-8-for-x86_64-baseos-rpms, rhel-8-for-x86_64-appstream-rpms, and ansible-2.9-for-rhel-8-x86_64-rpms.

Install a CentOS 7 or CentOS 8 server with this recommended setup:

  • 4 vCPUs
  • 4 GB of RAM
  • 30GB HD
  • Static IP

There is a sample kickstart file for EL 7 and EL 8 that is used during testing, if you'd like to automate the initial install of the OS.

Once the base OS is installed, install EPEL

yum -y install https://dl.fedoraproject.org/pub/epel/epel-release-latest-$(rpm -E %rhel).noarch.rpm

Next install ansible and git, then clone this repo.

yum -y install ansible git
git clone https://github.com/RedHatOfficial/ocp4-helpernode
cd ocp4-helpernode

Setup your Environment Vars

Inside that dir there is a vars.yaml file under docs/examples/var.yaml ... modify it to match your network and the environment. (the example one assumes a /24)

cp docs/examples/vars.yaml .

⚠️ NOTE, currently this playbook assumes/is limited to a /24 network

See the vars.yaml documentaion page for more info about what you can define. There are different options, depending on what you're doing. For example, if you're doing a static ip install vs a dhcp install.

Run the playbook

Once you edited your vars.yaml file; run the playbook

ansible-playbook -e @vars.yaml tasks/main.yml

Helper Script

You can run this script and it's options to display helpful information about the install and other post-install goodies.

/usr/local/bin/helpernodecheck

Install OpenShift 4 UPI

Now you're ready to follow the OCP4 UPI install doc

Quickstarts

The following are quickstarts. These are written using libvirt, but are generic enough to be used in BareMetal or other Virtualized Environments.

Contributing

Please see the contributing doc for more details.