EVE is Edge Virtualization Engine

EVE aims to develop an open, agnostic and standardized architecture unifying the approach to developing and orchestrating cloud-native applications across the enterprise on-premises edge. It offers users new levels of control through hardware-assisted virtualization of on-prem edge devices. Once installed, EVE has direct access to and control of underlying resources and provides standard APIs that allow more efficient use of resources and can effectively partition hardware to increase workload consolidation and application multi-tenancy.

EVE supports both ARM and Intel architectures and requires hardware-assisted virtualization. While EVE can run on a board as small as a $20 Orange Pi, the sweet spot for its deployment are IoT Gateways and Industrial PCs.

To get its job done, EVE leverages a lot of great open source projects: Xen Project, Linuxkit and Alpine Linux just to name a few. All of that functionality is being orchestrated by the Go microservices available under pkg/pillar. Why pillar? Well, because pillar is the kind of a monolith we need to break out into true, individual microservices under pkg/.

Download EVE

EVE LTS: Download latest LTS

How to use EVE with a controller (recommended)

EVE-OS can be used with the opensource Adam controller by following the instructions at Eden.

There are also ongoing development of EVE-OS tutorials.

How to use/build EVE-OS by itself

You will need QEMU 3.x+, Docker, Make and go 1.13+ installed in your system.

Use pre-built release binaries

EVE is an agile software project with bi-weekly release schedule. Each release gets tagged with x.y.z version in Git and a corresponding build is published on DockerHUB. As is common with Docker releases, EVE also uses version latest to designate the latest official release and snapshot to designate the latest build off of master branch.

Since EVE is not just an application, but a compute engine that expects to be deployed on real (or virtualized) hardware, you can't simply do docker run to give it a try. Instead, you need to use eve Docker container to produce one of the artifacts that you can then either run on bare metal hardware or deploy on virtualized infrastructure such as Google Compute Platform (GCP).

EVE Docker container lfedge/eve:<version> is used to produce these deployment artifacts.

Try running docker run lfedge/eve to get the most up-to-date help message.

The versions in the tag of lfedge/eve:<version> contain information as to which hypervisor and target architecture they support. The options are:

architecture: amd64, arm64, riscv64
hypervisor: kvm, xen, mini

Note that not all hypervisors are supported on all architectures.

For example:

docker run lfedge/eve:8.11.0-kvm-arm64 <command>: installer for 8.11.0 using kvm on arm64
docker run lfedge/eve:8.11.0-xen-arm64 <command>: installer for 8.11.0 using xen on arm64
docker run lfedge/eve:8.11.0-xen-amd64 <command>: installer for 8.11.0 using xen on amd64
docker run lfedge/eve:8.11.0-mini-riscv64 <command>: installer for 8.11.0 using mini on riscv64

Note that <command> is the appropriate command to run; leave it blank to get the help message.

If you leave off the architecture it will default to whatever architecture you are running on.

If you just use snapshot or latest, it will default to the architecture you are running on and the kvm hypervisor.

For example:

docker run lfedge/eve:8.11.0-kvm <command>: installer for 8.11.0 using kvm on your architecture
docker run lfedge/eve:latest <command>: installer for latest image using kvm on your architecture

Note that each docker image is built for the architecture for which it runs. Thus lfedge/eve:8.11.0-kvm-arm64 not only installs an arm64 EVE image, but the docker image is intended to be run on arm64. If you are running on arm64, e.g. Mac M1, this works fine. If you are running on an amd64 architecture, docker normally will determine the right architecture.

However, you should indicate to docker your target platform via --platform:

docker run --platform=linux/arm64 lfedge/eve:8.11.0-kvm-arm64

docker run --platform=linux/amd64 lfedge/eve:8.11.0-kvm-amd64

The above is unnecessary, but does not hurt, if you already are running on the target architecture.

Install Dependencies

The following steps are required to build and run EVE from source:

Get Go

https://golang.org/dl/

Get Docker

https://docs.docker.com/engine/install/

Make sure that Docker is up and running on your system. On MacOS just start a docker Application, on Linux make sure docker service is running. Regardless of how you start Docker you can make sure that it is ready for you by running the following command and making sure that it returns both a version of the client AND a version of the server:

docker version

Get system dependencies (git, make, qemu, jq, gnu-sed)

On OSX (using Brew)

$ brew install git make jq qemu gnu-sed

NOTE: (M1 Macs) qemu may also require python3 nettle ninja gnu-tar to install properly, that is:
$ brew install git make jq python3 nettle ninja qemu gnu-sed gnu-tar

On Ubuntu Linux

$ sudo apt-get install -y git make jq qemu binfmt-support qemu-user-static \
    qemu-utils qemu-system-x86 qemu-system-aarch64

Setup Docker

Enable execution of different multi-architecture containers

This step is required on Linux and is required to create eve bootable images with a different architecture than the host architecture.

$ docker run --rm --privileged multiarch/qemu-user-static --reset -p yes

NOTE: Should a cross build fail:

For docker to emulate a chip architecture different from the build host, perform this additional step:
$ docker run --privileged --rm tonistiigi/binfmt --install all
This provides the appropriate binfmt-support containers supporting cross execution. See the reddit article, docker hub, private project page, or the source.

Get Project EVE

EVE requires being built in a Git repository (the tools keep looking up git commit IDs). The easiest way is to clone EVE repository from GitHub:

git clone https://github.com/lf-edge/eve.git
cd eve

Build Project EVE

Build both the build-tools as well as the live image in the source directory:

make build-tools
make live

This will download the relevant docker images from docker hub and create a bootable image dist/<ARCH>/current/live.img.

Since almost all developer workflow is driven by the Makefile, it may be useful to familiarize yourself with various Makefile targets that Project EVE offers. A short summary of those is available by simply running make without any arguments make and a more detailed explanation is available as part of our documentation

NOTE: Since the initial build fetches a LOT of bits over the network it may occasionally time out and fail. Typically re-running make fixes the issue. If it doesn't you can attempt a local build of all the required EVE packages first by running make pkgs

NOTE: use make parameter "-j" edit number of threads to build faster. set number of threads suggestions CPU*2. on OSX show number of CPU : sysctl hw.ncpu; on Ubuntu Linux show number of CPU : nproc;

Proxies

Building of the various images may require downloading packages from the Internet. If you have direct Internet access, everything will "just work". On the other hand, if you need to run behind a proxy, you may run into issues downloading. These manifest in two key areas:

docker: docker needs to download images from the image registries. Configuring your local installation of docker is beyond the scope of this document, please see here.
packages: the package updates inside the images running in docker may need to use http/s proxies.

To configure your build process to use proxies, you can set the following environment variables. They will be picked up automatically when running any make commands and used within the building containers. If they are not set, no proxy is set:

HTTP_PROXY
HTTPS_PROXY
ALL_PROXY
NO_PROXY

Running in QEMU

Finally run the resulting image in QEMU with some default assumptions:

make run

NOTE: The default QEMU configuration needs 4GB of memory available. If you get an error message about being unable to allocate memory, try freeing up some RAM. If you can't free up 4GB, you can reduce the memory allocation to qemu from 4096 (4GB) to 2048 (2GB). Running QEMU with less than 2GB of memory is not recommended. To run with a different amount of memory, provide the desired amount in KB as:

make run QEMU_MEMORY=2048

NOTE: make run launches qemu with the -bios option. On some systems, this does not work, and you need to run it with the -pflash argument (or its equivalent properly configured -drive instead). To enable pflash, run:

make run PFLASH=true

Once the image boots you can interact with it either by using the console (right there in the terminal window from which make run was executed). Your shell in the console is connected to the 'host' os. Everything interesting is actually happening in the pillar container. Use eve enter command to enter it (or if you're comfortable with ctr CLI from containerd - use that instead).

Once in a container you can run the usual xl commands to start VMs and interact with Xen.

Exiting

To exit out of the QEMU environment, press Ctrl-A + C to reach the QEMU console, then q to quit.

Linux

$ exit # leave eve
$ poweroff -f # leave qemu

Customizing the Configuration

As described in BUILD.md and REGISTRATION.md, a booting EVE looks in its config partition to determine:

the URL to a Controller
[OPTIONAL] hostnames to add to the /etc/hosts file
certificates to trust
[OPTIONAL] initial device configuration (aka bootstrap) used only until device is onboarded

When run in an emulator using make run, you can override the built-in /config partition by passing it the path of a directory to mount as that partition:

make run CONF_PART=/path/to/partition

Note that the directory must exist to be mounted; if not, it will be ignored. The most common use case is a config directory output on the run of adam.

While running everything on your laptop with QEMU could be fun, nothing beats real hardware. The most cost-effective option, not surprisingly, is ARM. We recommend two popular board HiKey and Raspberry Pi 4. The biggest difference between the two is that on Raspberry Pi (since it doesn't have any built-in flash storage) you won't be able to utilize EVE's installer and you'll have to build a live image. With HiKey you can use a standard EVE's installer. The steps to do both are outlined below:

How to use on a Raspberry Pi 4 ARM board

Raspberry Pi 4 is a tiny, but capable enough ARM board that allows EVE to run with either Xen or KVM hypervisors. While EVE would run in the lowest memory configuration (1GB) if you plan to use it for actual EVE development we strongly recommend buying a 4GB RAM option.

Since a full Raspberry Pi 4 support is only available in upstream Linux kernels starting from 5.6.0, you'll have to use that bleeding edge kernel for your build. Another peculiar aspect of this board is that it doesn't use a standard bootloader (e.g. u-boot or UEFI) so we need to trick it into using our own u-boot as UEFI environment. Thankfully, our Makefile logic tries to automate as much of it as possible. Thus, putting it all together, here are the steps to run EVE on Raspberry Pi 4:

Make sure you have a clean build directory (since this is a non-standard build) rm -rf dist/arm64
Build a live image make ZARCH=arm64 HV=kvm live-raw (or make ZARCH=arm64 HV=xen live-raw if you want XEN by default)
Flash the dist/arm64/current/live.raw live EVE image onto your SD card by following these instructions

Once your Raspberry Pi 4 is happily running an EVE image you can start using EVE controller for further updates (so that you don't ever have to take an SD card out of your board). Build your rootfs by running make ZARCH=arm64 HV=xen rootfs (or make ZARCH=arm64 HV=kvm rootfs if you want KVM by default) and give resulting dist/arm64/current/installer/rootfs.img to the controller.

How to use on an HiKey ARM board

Unlike Raspberry Pi boards, HiKey boards come with a built-in flash, so we will be using EVE's installer to install a copy of EVE onto that storage. You can follow these steps to prepare your installation media:

Start by cloning EVE git repository git clone https://github.com/lf-edge/eve.git
Build an installer image cd eve ; make ZARCH=arm64 installer
Flash the dist/arm64/current/installer.raw onto the USB stick by following these instructions

Since by default HiKey is using WiFi for all its networking, you will also have to provide SSID and password for your WiFi network. On Mac OS X you can simply re-insert SD card and edit wpa_supplicant.conf that will appear on volume called EVE.

At this point you have everything you need to permanently install onto HiKey's internal flash. This, of course, will mean that if you have anything else installed there (like a Debian or Android OS) it will be replaced so make sure to make a backup if you nee to.

Additionally, our installer will try to configure an entry point to the initial boot sequence via GRUB. Since the only reliable way to do so is by replacing a file called fastboot.efi in the system boot partition you need to make sure that you have fastboot.efi present there (since if isn't there installer will refuse to proceed). The easiest way to check for all that is to invoke an EFI shell on HiKey. Here's how: put the SD card into the KiKey, connect HiKey to your serial port, start screen, poweron HiKey and immediately start pressing <ESC> key to trigger EFI shell:

screen /dev/tty.usbserial-* 115200

[1] fastboot
[2] boot from eMMC
[3] boot from SD card
[4] Shell
[5] Boot Manager
Start: 4
.....
Press ESC in 4 seconds to skip startup.nsh or any other key to continue.

Shell> ls fs2:\EFI\BOOT\fastboot.efi
Shell> setsize 1 fs2:\EFI\BOOT\fastboot.efi

NOTE: you only need to execute the last (setsize) command if, for whatever reason, the previous command doesn't show fastboot.efi present on your system. Once you've either verified that there's an existing fastboot.efi (or created a dummy one via the setsize command) you can proceed with the rest of the installation from the same EFI shell by executing:

Shell> fs0:\EFI\BOOT\BOOTX64.EFI

You will see an installation sequence scroll on screen and the output that indicates a successful install will look like this:

[   85.717414]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p11
[   87.420407]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p11 p12
[  118.754353]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p11 p12 p13
[  119.801805]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p11 p12 p13 p14
[  120.992048]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p11 p12 p13 p14 p19
[  127.191119] reboot: Power down
(XEN) Hardware Dom0 halted: halting machine

At this point you should remove your SD card from HiKey's slot and reboot the board. If everything went as planned you will boot right into the running system. One thing that you will notice is that a successful installation sequence made a backup copy of your existing fastboot.efi under the fastboot.efi.XXX name. This allows you to restore your HiKey to a pristine state without going through a full fledged re-flashing sequence.

Alternatively, if you're not quite ready to commit to replace your current OS on the HiKey, you can try running from the SD card. For that you will have to put a live system on the SD card, not the installer. Here's how you can do that on Mac OS X:

vi conf/wpa_supplicant.conf
  # put your WIFI passwords in and/or add your own networks
make ZARCH=arm64 MEDIA_SIZE=8192 live
sudo dd if=dist/arm64/current/live.raw of=/dev/rdiskXXX bs=1m

Then you can boot into a live system from triggering UEFI shell like shown above and executing exactly the same boot command:

Shell> fs0:\EFI\BOOT\BOOTX64.EFI

How to use on a Jetson nano 4GB ARM board

In Jetson nano, from January 22, 2021, it became possible to save the u-boot to an internal qspi chip. Following the instructions from the first point and specifying the kernel and u-boot versions in the same way as in EVE, we can run it on the Jetson nano with 4GB of RAM.

Follow steps in instruction for flash jetson boot flow partitions to qspi.
Make sure you have a clean build directory (since this is a non-standard build) rm -rf dist/arm64
Build a live image make ZARCH=arm64 HV=kvm live-raw (Only KVM is supported)
Flash the dist/arm64/current/live.raw live EVE image onto your SD card by following these instructions

How to use on a Jetson Xavier NX platform

Currently EVE supports the following devices from NVIDIA's Jetson Xavier NX platform:

Lenovo ThinkEdge SE70
Siemens SIMATIC IPC520A
NVIDIA Jetson Xavier NX developer kit

See NVIDIA-NX.md for instructions on how to build and deploy EVE on these devices.

How to use on a i.MX 8MQuad Evaluation Kit ARM board

Set SW801 to 1100 for switch boot device to SD card.
Build a live image make ZARCH=arm64 HV=kvm PLATFORM=imx8mq_evk live-raw (Only KVM is supported)
Flash the dist/arm64/current/live.raw live EVE image onto your SD card by following these instructions

How to use on an i.MX 8M Plus Phytec phyBOARD-Pollux board

Running from SD Card (phyBOARD-Pollux)

Set bootmode switch (S3) to boot device from an SD card (positions 1,2,3,4 set to ON,OFF,OFF,OFF).
Build a live image make ZARCH=arm64 HV=kvm PLATFORM=imx8mp_pollux live-raw (Only KVM is supported)
Flash the dist/arm64/current/live.raw live EVE image onto your SD card by following these instructions

Installing on eMMC (phyBOARD-Pollux)

Build an installation raw image make ZARCH=arm64 HV=kvm PLATFORM=imx8mp_pollux installer-raw (Only KVM is supported)
Flash the dist/arm64/current/installer.raw install EVE image onto your SD card by following these instructions
Set bootmode switch (S3) to boot device from an SD card (positions 1,2,3,4 set to ON,OFF,OFF,OFF).
Boot the device from SD Card. Installation process should initialize automatically, the device will be powered off when the process is done
Remove the SD Card from the device
Set bootmode switch (S3) to boot device from eMMC (positions 1,2,3,4 set to OFF,OFF,OFF,OFF).
Power on the device, EVE should start from eMMC

How to use on an EPC-R3720 (Advantech, based on i.MX 8M Plus)

This device, from Advantech, it's an Edge AI Box Computer based on the NXP i.MX 8M Plus SoC. Three different models are available. EVE was tested and it supports the model EPC-R3720IQ-ALA220. The installation should be performed through the following steps according to the main boot device: SD Card or eMMC.

Running from SD Card (EPC-R3720)

Set Boot Select switch (SW1) to boot device from an SD card (positions 1,2,3,4 set to ON,ON,OFF,OFF).
Build a live image make ZARCH=arm64 HV=kvm PLATFORM=imx8mp_epc_r3720 live-raw (Only KVM is supported)
Flash the dist/arm64/current/live.raw live EVE image onto your SD card by following these instructions

Installing on eMMC (EPC-R3720)

Build an installation raw image make ZARCH=arm64 HV=kvm PLATFORM=imx8mp_epc_r3720 installer-raw (Only KVM is supported)
Flash the dist/arm64/current/installer.raw install EVE image onto your SD card by following these instructions
Set Boot Select switch (SW1) to boot device from an SD card (positions 1,2,3,4 set to ON,ON,OFF,OFF).
Boot the device from SD Card. Installation process should initialize automatically, the device will be powered off when the process is done
Remove the SD Card from the device
Set Boot Select switch (SW1) to boot device from eMMC (positions 1,2,3,4 set to OFF,ON,OFF,OFF).
Power on the device, EVE should start from eMMC

How to use on an AMD board

The following steps have been tested on Intel UP Squared Board (AAEON UP-APL01) and the bootable USB Disk containing the installer image has been made on Ubuntu 16.04:

Start by cloning EVE git repository git clone https://github.com/lf-edge/eve.git
Build an installer image cd eve ; make ZARCH=amd64 installer
Flash the dist/amd64/current/installer.raw onto the USB stick by following these instructions
Now plug the USB Disk on your UP Squared Board and the installer should now replace the existing OS on the UP Squared board with EVE

You will see an installation sequence scroll on screen and the output that indicates a successful install will look like this:

[10.69716164] mmcblk0:
[11.915943]   mmcblk0: p1
[13.606346]   mmcblk0: p1 p2
[29.656563]   mmcblk0: p1 p2 p3
[30.876806]   mmcblk0: p1 p2 p3 p4
[32.156930]   mmcblk0: p1 p2 p3 p4 p9
NOTICE: Device will now power off. Remove the USB stick and power it back on to complete the installation.
[43.185325]   ACPI: Preparing to enter system sleep state S5
[43.187349]   reboot: Power down

At this point you should remove your USB Disk from the UP Squared Board slot and reboot the board. If everything went as planned you will boot right into the running system.

How to write the EVE image and installer onto storage media

These instructions show you how to install EVE or the installer onto an installation medium, such as disk or USB or SD card.

EVE is an operating system with installer with particular requirements for the storage on which it is installed. It installs to the entire medium. You must be careful to enter commands correctly and be sure the selected devices are correct. If you select the wrong target device, you can completely overwrite the main storage disk and operating system system you're running on, instead of the target storage device.

PROCEED AT YOUR OWN RISK

To install any binary EVE artifact, such as installer.img, onto an installation medium, do the following. Be sure to replace installer.img with the name of the artifact.

Prepare the artifact.
Find the target device.
Flash the image to the device.

1. Prepare the artifact

Prepare the artifact, either by downloading from the releases page or running the EVE docker command docker run lfedge/eve <command>. For example, docker run lfedge/eve will show the help message.

If you want a raw disk image to install, which is useful for SD cards and USB, run:

docker run lfedge/eve installer_raw > installer.img

For an ISO, useful for CD/DVD:

docker run lfedge/eve installer_iso > installer.iso

2. Find the target device

Discover the target device to which you will be writing.

Target device on Linux

fdisk -l

Target device on macOS

diskutil list

3. Flash the image to the device

Flash the disk image to the USB stick, SD card, or CD/DVD.

Flash image on Linux

If the target device is /dev/sdX, where X is the device letter, and the image is installer.img, run:

umount /dev/sdX
sudo dd if=installer.img of=/dev/sdX
eject /dev/sdX

Flash image on macOS

If the target device is /dev/disk8, and the image is installer.img, run:

diskutil unmountDisk /dev/disk8
sudo dd if=installer.bin of=/dev/disk8
diskutil eject /dev/disk8

Graphical interface

Alternatively, the image can be flashed with interactive graphical tools like:

unetbootin - Linux, Windows, macOS
imageUSB - Windows
rufus - Windows
ventoy - Linux, Windows
Disk Utility - macOS

Disclaimer: The above tools are third-party software and are not maintained by the EVE project. The EVE project and lf-edge take no responsibility for those tools. Evaluate and use them at your own risk.

A quick note on linuxkit

You may be wondering why do we have a container-based architecture for a Xen-centric environment. First of all, OCI containers are a key type of a workload for our platform. Which means having OCI environment to run them is a key requirement. We run them via:

Set up the filesystem root using containerd
Launch the domU using Xen via xl

In addition to that, while we plan to build a fully disaggregated system (with even device drivers running in their separate domains) right now we are just getting started and having containers as a first step towards full disaggregation seems like a very convenient stepping stone.

Let us know what you think by filing GitHub issues, and feel free to send us pull requests if something doesn't quite work.

License

Distributed under the Apache License 2.0. See LICENSE.txt for more information.

deitch/eve