donovan6000/iMe

Issues

• Cannot connect to M3D Micro on MacOS Big Sur

  #71 opened 4 years ago by IhorSyerkov
  7

• device not detected

  #73 opened 4 years ago by davidwatters
  0

• Invalid G codes?

  #55 opened 8 years ago by erickphd
  51

• M3D Micro+

  #61 opened 7 years ago by AshMartian
  4

• Z axis shifts during printing

  #70 opened 5 years ago by junhongmit
  4

• M3D Pro

  #69 opened 5 years ago by svanichkin
  0

• Disconnects immediately after connect (ubuntu 18.04)

  #68 opened 5 years ago by risacher
  2

• No safety features

  #67 opened 6 years ago by guysoft
  10

• Is there a way to limit bed size in firmware

  #66 opened 6 years ago by guysoft
  1

• M33 Manager won't disconnect

  #65 opened 7 years ago by NeoMatrixJR
  1

• Printer occasionally gets lost

  #63 opened 7 years ago by cynr1c
  3

• Movement too big

  #64 opened 7 years ago by Fullmono
  0

• Seg fault when running M33 Manager on Ubuntu Linux 17.10

  #62 opened 7 years ago by ianc1215
  2

• Question: Bootloader

  #59 opened 7 years ago by sam-dyer
  1

• All of the printer's peripherals will be set to their default state... ...

  #60 opened 7 years ago by Tobitulpe
  0

• Extruder does not move with iMe 1.24

  #56 opened 7 years ago by alancnet
  4

• Printer stuck on "positioning extruder" when trying to unload filament

  #51 opened 7 years ago by Nold360
  2

• iMe hex too big

  #52 opened 7 years ago by WilliamRodriguez42
  1

• Building iMe, .hex to big

  #50 opened 8 years ago by MaxTimothy
  4

• Z X Y is broken 1.18 Movement is big

  #42 opened 8 years ago by qwerty8224
  21

• Thanks to Donovan6000 )))

  #45 opened 8 years ago by qwerty8224
  2

• Question?

  #37 opened 8 years ago by qwerty8224
  5

• There is a proposal)

  #41 opened 8 years ago by qwerty8224
  1

• Octoprint 1.6 IME 1.12

  #36 opened 8 years ago by qwerty8224
  10

• iME 1.13 Bias backslash 900 IME 1.12 backslash 1500 GOOD

  #40 opened 8 years ago by qwerty8224
  2

• Z Skips team

  #38 opened 8 years ago by qwerty8224
  6

• iME 1.13 Bias backslash 900 IME 1.12 backslash 1500 GOOD

  #39 opened 8 years ago by qwerty8224
  0

• Check G32 stops the left rear

  #34 opened 8 years ago by qwerty8224
  5

• Occasional calibration issues

  #30 opened 8 years ago by analogmonster
  6

• Offset Y axis X

  #33 opened 8 years ago by qwerty8224
  4

• Offset Y axis

  #32 opened 8 years ago by qwerty8224
  0

• Motor idle pitching sound

  #14 opened 8 years ago by stephenci
  4

• Printing movement stuttering with Mattercontrol

  #12 opened 8 years ago by stephenci
  3

• Sentence .....

  #31 opened 8 years ago by qwerty8224
  1

• Calibration bed pozition error Z0 Y-axis

  #28 opened 8 years ago by qwerty8224
  11

• gantry movement confusion

  #27 opened 8 years ago by analogmonster
  5

• iMe and Simplify3d cause print to tilt

  #26 opened 8 years ago by neonode
  45

• Backlash settings

  #25 opened 8 years ago by neonode
  8

• Prompt command to disable the extruder heating?

  #21 opened 9 years ago by qwerty8224
  2

• Extruder heating during calibration?

  #20 opened 9 years ago by qwerty8224
  0

• Mattecontrol small Offset X

  #19 opened 9 years ago by qwerty8224
  0

• How can I raise the current to the motor?

  #17 opened 9 years ago by qwerty8224
  2

• Print speed?

  #15 opened 9 years ago by qwerty8224
  0

• Manager compilation for Raspberry Pi

  #16 opened 9 years ago by th0ma5w
  2

• Mattercontrol

  #13 opened 9 years ago by qwerty8224
  4

• schedule frozen temperature.Octo Print

  #8 opened 9 years ago by qwerty8224
  1

• Bed Height Offset

  #11 opened 9 years ago by qwerty8224
  8

• temperature problem

  #7 opened 9 years ago by qwerty8224
  2

• Connection 4 com port

  #5 opened 9 years ago by qwerty8224
  0

• Incorrect display extruder temperature?

  #4 opened 9 years ago by qwerty8224
  0