This is a DBC CAN provider for the KUKSA.val Server and Databroker. For KUKSA Server it supports receiving data from CAN and sending to Server. For KUKSA Databroker it supports both receiving data from CAN and sending to Databroker as well as subscribing to VSS signals in Databroker and sending to CAN.
The basic operation is as follows:
The provider connects to a socket CAN interface. In dbc2val-mode it reads raw CAN data, that will be parsed based on a DBC file.
The mapping file (called vss_dbc.json in the picture) describes mappings between VSS signals and DBC signals.
The respective data point is then sent to KUKSA Databroker or Server.
It is also possible to replay CAN dumpfiles without the SocketCAN interface being available, e.g. in a CI test environment.
See "Steps for a local dbc2val test with replaying a can dump file"
Val2dbc-mode works similar, but in the opposite direction, taking data from KUKSA and sending on CAN. The CAN sending functionality relies on that all signals in the CAN frame must have a value. This is solved by using default values, if the provider does not have a VSS mapping for a specific DBC signal, or has not received a value from KUKSA, then the default value will be used. Default values shall be provided by a JSON file, an example file exists in dbc_default_values.json.
Note: If you use the files provided in this repository default values are only included for CAN id 258!
+-------------+
| DBCFile |
+-------------+ +------------------+
| | |
| |--->| KUKSA Server |
| | | |
| | +------------------+
+-----------------+ | |
| | +-------|------+ |
| CAN Interface | | | |
| or |<------ >| CAN Provider |<--OR--|
| dumpfile replay | | | |
| | +--------------+ |
+-----------------+ | | +------------------+
| | | |
+--------------+ |--->| KUKSA Databroker |
| vss_dbc.json | | |
+--------------+ +------------------+
By default only dbc2val-mode is enabled!
Install can utils, e.g. in Ubuntu do:
sudo apt update
sudo apt install can-utilsCheck that at least Python version 3.9 is installed
python -VInstall the needed python packages
pip install -r requirements.txtNote - Sometimes DBC provider on main branch rely on a kuksa-client pre-release. Then you must add --pre to the command above!
If you want to run tests and linters, you will also need to install development dependencies
pip install -r requirements-dev.txtThe CAN provider requires a mapping file as input. The mapping file describes mapping between VSS signals and CAN (DBC) signals. It shall be a JSON file with VSS syntax with metadata for dbc information. Please see mapping documentation for more information.
The CAN provider support a wide range of configurations.
Please see CAN Provider Configuration for more information on how to use the CAN Provider for different scenarios.
The KUKSA project publish the CAN provider as a Docker container. Please see CAN Provider Docker Setup for more information on how to build and use the CAN Provider as a Docker container.
CAN dump files are usable for test purposes. This repository contain two dump files which are used for testing and also used as basis for the examples in this repository.
candump-2021-12-08_151848.log.xz is a CAN trace from 2018 Tesla M3 with software 2021.40.6. This data is interpreted using the Model3CAN.dbc maintained by Josh Wardell.
The canlog in the repo is compressed, to uncompress it (will be around 150MB) do
unxz candump-2021-12-08_151848.log.xzcandump.log: A smaller excerpt from the above sample, with fewer signals.
This repository is set up to use pre-commit hooks.
Use pip install pre-commit to install pre-commit.
After you clone the project, run pre-commit install to install pre-commit into your git hooks.
Pre-commit will now run on every commit.
Every time you clone a project using pre-commit running pre-commit install should always be the first thing you do.