eez-open/psu-hw

Issues

• Cheaper triacs for soft-start/power up control

  #63 opened 5 years ago by prasimix
  0

• Typos in power board description

  #55 opened 5 years ago by Erik-k
  1

• Arduino Due issue with USB "native" port

  #53 opened 5 years ago by jlegen
  12

• Multiple fixed outputs for digital design

  #22 opened 5 years ago by PurnenduK90
  3

• Grammar fixes for Assembly instructions

  #48 opened 5 years ago by Cabalist
  2

• Expected self test failures

  #70 opened 5 years ago by jfitter
  5

• Down-programmer MOSFET package

  #69 opened 6 years ago by prasimix
  0

• Migrate Eagle to free EDA such as KiCad

  #37 opened 8 years ago by prasimix
  2

• Replace ADG465 with zener diode

  #65 opened 6 years ago by prasimix
  1

• ZD7 placement

  #64 opened 6 years ago by prasimix
  1

• All temperature sensors measures unrealistically high temperatures

  #49 opened 7 years ago by prasimix
  0

• Two screws for additional AC/DC modules fixing are missing

  #50 opened 7 years ago by stolens
  2

• Missing information about TFT display in BOM

  #62 opened 7 years ago by prasimix
  0

• Consider presenting at FOSDEM in 2018

  #61 opened 7 years ago by kasbah
  1

• Soft start and DOUT2 controls

  #36 opened 7 years ago by prasimix
  1

• Remove JP5, JP6, JP7 on Arduino shield

  #59 opened 7 years ago by prasimix
  0

• R93 PCB layout spacing

  #60 opened 7 years ago by prasimix
  0

• Output enters unregulated mode too early (below ~1.8 V)

  #42 opened 7 years ago by prasimix
  0

• High range sense resistor

  #40 opened 7 years ago by prasimix
  2

• Additional current range(s)

  #41 opened 7 years ago by prasimix
  1

• USB isolator speed selection

  #56 opened 7 years ago by prasimix
  1

• Overvoltage protection for V+ output

  #46 opened 7 years ago by prasimix
  0

• Remote sense resistors

  #44 opened 7 years ago by prasimix
  0

• X12, X14 connection improvement on PCB

  #43 opened 7 years ago by prasimix
  0

• Minor: one connector orientation unclear from assembly instructions

  #58 opened 7 years ago by raplin
  2

• X12 X14 Pin confusion

  #57 opened 7 years ago by dagema
  2

• Various issues (self-test failure, etc.)

  #54 opened 7 years ago by ulaker
  31

• AC power switch failure and TR1 +12V rail failure

  #47 opened 7 years ago by madscientist159
  18

• Difficult or unable to attach power modules to case...

  #52 opened 7 years ago by mloftis
  6

• Power board self-test fail on newly assembled H24005

  #51 opened 7 years ago by amuir2k
  2

• User manual for the EEZ H24005

  #45 opened 7 years ago by prasimix
  0

• Swap encoder A and B pins

  #39 opened 8 years ago by prasimix
  1

• Pin numbering of L1 (RN112-4-02) is wrong.

  #38 opened 8 years ago by phuebner
  1

• BOM Errors?

  #35 opened 8 years ago by jwilhelm1
  5

• Cannot reach max. current in LOW range mode

  #33 opened 8 years ago by prasimix
  1

• RJ45 modular jack replacement

  #34 opened 8 years ago by prasimix
  1

• CC mode in current low range

  #32 opened 8 years ago by prasimix
  1

• Dual range current

  #26 opened 8 years ago by prasimix
  2

• 1M resistor in parallel with Ethernet controller crystal

  #31 opened 8 years ago by prasimix
  1

• Micro SD card socket

  #30 opened 8 years ago by prasimix
  1

• Where can I find the complete schematic diagrams?

  #29 opened 8 years ago by dagema
  1

• Ethernet LEDs connected wrong

  #28 opened 8 years ago by dsaltas
  1

• possible spike when switching sense relay

  #27 opened 8 years ago by faultylee
  2

• Additional Vin capacitor on Power board

  #19 opened 8 years ago by prasimix
  1

• Encoder with switch on Arduino shield

  #20 opened 8 years ago by prasimix
  1

• Rsense with 4-terminal sensing

  #21 opened 8 years ago by prasimix
  1

• Power relay MCU controlled on the AUX PS module

  #23 opened 8 years ago by prasimix
  1

• Support for 3.5" Riverdi TFT touchscreen display

  #24 opened 8 years ago by prasimix
  1

• Protection improvement for DC power input

  #25 opened 8 years ago by prasimix
  1

• Wrong positions of DOUT pins on X14 push-in connector

  #18 opened 8 years ago by prasimix
  1