Virtual modem for ESP8266

Schematic Copyright (C) 2018 Daniel Jameson djameson@gmail.com PCB Copyright (C) 2018 Daniel Jameson djameson@gmail.com Schematic and PCB released under Creative Commons Attribution-ShareAlike 4.0 License: https://creativecommons.org/licenses/by-sa/4.0/legalcode

FreeFi232 is UNTESTED!

Getting Started with the BBC Micro

You will need: 1x LoLin NodeMCU board with an ESP12E module on it 1x MAX3232 level shifter board - not just the IC on its own! 1x Domino plug for the beeb's serial... Some wire for wiring things together.

On your modern computer you need: The Arduino IDE: https://www.arduino.cc/en/Main/Software The source for the firmware. If you wish to compile it with hardware flow (RTS/CTS), make sure you've got access to GPIO pins 13/15 of the ESP8266 and adjust the #defines in the source. Ensure RTS/CTS are hooked up appropriately to your terminal.

On the beeb you need: Commstar 1.4

1st, you need to get the ESP8266 environment set up on the Arduino IDE. Instructions here: http://www.instructables.com/id/Quick-Start-to-Nodemcu-ESP8266-on-Arduino-IDE/

Once you're sure that you can compile and upload sketches to the NodeMCU board, compile and upload the ESP8266 modem sketch.

Next step is to hook this up to the BBC/Master.

On the domino plug, looking at the solder side, join pins 5/2 (RTS/CTS), and take lines from GND (centre pin 1), RD (4) and TD (3). Take TD to the TxD pin on your level shifter and RD to the RxD pin, and GND to GND.

On the other side, the MAX3232 will need 3.3V from somewhere and you can bring the GND from it out to attach to the LoLin board...

Connect the TxD output to the TX pin on the LoLin board, and the RxD output to the RX pin of the LoLin board, GND to G, and then it's up to you to choose how to power the LoLin board - you can take 5V and feed that to the VIN pin, or you can just use a USB adapter and power it through that. Entirely up to you. JUST DON'T FEED 5V TO ONE OF THE PINS MARKED 3V! YOU WILL FRY YOUR BOARD!

You should now have a working WiFi telnet modem!

More General Overview

ESP8266 is a tiny MCU module with WIFI. It already contains a virtual modem firmware by factory but I wanted to make one myself to support a wider range of baud rates. For example Commodore 64 requires 2400 or lower. Now it is also possible to add additional features in the future because this is open source. For example, translation tables for different character sets or file transfer protocol conversions on the fly with help of a buffer in MCU memory.

AT command examples

Change baud rate: AT115200
Connect to WIFI: ATWIFIMyAccessPoint,MyPassword1234
Connect by TCP: ATDTsome.bbs.com:23
Disable telnet command handling: ATNET0
Get my IP: ATIP
Make a HTTP GET request: ATGEThttp://host:80/path
Answer a RING: ATA
Disconnect: +++ (following a delay of a second)

Note that the key and port are optional parameters. Port defaults to 23. All parameters are case sensitive, the command itself not. You must always connect to an access point before dialing, otherwise you get an error. When you connect to WIFI you get either OK or ERROR after a while, depending on if it succeeded. If you get ERROR the connection might still occur by itself some time later, in case you had a slow AP or slow DHCP server in the network. When dialing, you get either CONNECT when successfully connected or ERROR if the connection couldn't be made. Reasons can be that the remote service is down or the host name is mistyped.

Default Baud rate is defined in the code. 2400 is safe for C64 and 19200 for any PC and Amiga. 115200 for PC's with "new" 16550 UART. You must always have that default rate on the terminal when powering on. After giving a command for a higher rate nothing is replied, just switch to the new baud rate in your terminal as well. Then you can give next command in the new baud rate. Note that the first command after switching baud rate might fail because the serial port hardware is not fully synchronized yet, so it might be good idea to simply give "AT" command and wait for "ERROR" or "OK" before giving an actual command.

Example communication

OK
ATWIFIMyAccessPoint,MyPassword
Connecting to MyAccessPoint/MyPassword
OK
ATDTbat.org
Connecting to bat.org:23
CONNECT


    __|\/|__             __|\/|__           __|\/|__       __|\/|__  Logo
     \<..>/               \<..>/             \<..>/         \<..>/    by:
             |\_/|                                      |\_/|          Gar
       ______|0 0|______   /////// //\\ \\\\\\\   ______|0 0|______
        \| | |   |  | |/  //   // //  \\    \\     \| | |   |  | |/
          \|..\./...|/   /////// ////\\\\    \\      \|..\./...|/

A more detailed example can be seen on my YouTube video at: https://youtu.be/oiP5Clx3D_s

Hints

The module can also be used for other than telnet connections, for example you can connect to HTTP port, send a HTTP request and receive a response.

I made a 3D printable case for the C64: http://www.thingiverse.com/thing:1545605 If you build it for any other device you can use any generic case because you need room for a RS232 level converter such as MAX232, and you do not need holes for any rare connectors.

Future plans and status

It seems quite complete for me but please send ideas.
I tested huge transfers with ZModem, seems to be working. Remember to use -e parameter with sz and rz if using over a telnetd.
Serial multiplayer game of Doom (sersetup.exe) seems to be also working. Remember to use ATNET0 when playing serial games, also on DosBox emulator if it's the other host.

elminster/esp8266_modem