FriendlyARM - Tiny6410

Hardware	description
CPU	SAMSUNG S3C6410, run at 533Mhz, up to 667Mhz
Board	Tiny6410 (v1308)
Expander Board	Tiny6410SDK(TinyADK 1312B) with 7"LCD

folder	description
arm-asm	ARM-S3C6410 Assembler
no-os	ARM-S3C6410 Bare-Metal Program
linux	ARM-S3C6410 Linux Program
doc	ARM-S3C6410 documents

##核心板: Tiny6410 - v1308 SDRAM: SAMSUNG K4X2G323PD-8GD8 Mobile DDR 64Mx32 200Mhz Halogen Free FBGA90 DRAM 64Mbx32 = 2048Mb = 2Gb = 256MB

NAND FLASH: SAMSUNG K9K8G08U0E-SCB0, 8G bit Nand Flash 1Gx8 SLC 
			 
LED:		LED1 ~ LED4 (nLED_1 ~ nLED_4), 低电平点亮LED.
				LED1 - GPK4
				LED2 - GPK5
				LED3 - GPK6
				LED4 - GPK7
				
JTAG:		10 pin 2.0mm space Jtag connector
Button:		Reset button, 连接M_nRESET接口, 低电平有效;
Power:		Supply Voltage from 2.0V to 6V

Crystal:	Y1 - 12M - ( XTO , XTI )				- 外部时钟	
			Y2 - 27M - ( 27MXTO , 27MXTI )			- X27MXTO
			Y3 - 48M - ( OTGTO , OTGTI )			- USB OTG 时钟
			Y4 - 32.768K - ( RTCTO , RTCTI ) 		- RTC 时钟

####NAND FLASH: SAMSUNG K9K8G08U0E-SCB0, 8G bit Nand Flash,1Gx8 SLC
K9F4G08U0E , K9K8G08U0E, 同一个芯片手册;

型号说明： http://www.elnec.com/device/Samsung/K9F4G08U0E+%5BTSOP48%5D/

- K = Memory
- 9 = NAND Flash
- F = SLC Normal ; K = SLC Die Normal, SLC Die stack;
- Density: 4G = 4Gbit, 8G = 8Gbit;
- Technology: 0 = Normal (x8)
	- Organization: 8 = x8
	- Supply Voltage: U = 2.7V to 3.6V
	- Mode: 0 = Normal
	- Generation: E = 6th generation

####SDRAM - K4X2G323PD-8GD8 http://www.samsung.com/us/business/oem-solutions/pdfs/PSG_2H_2012.pdf

K4X2G323PD-8GD8 
K:		SAMSUNG Memort
4:	 	DRAM
X:		Mobile DDR SDRAM
2G:	2G, 8K/64ms
32:	x32 (bit organization)		3:		4 of Internal Banks
P:		LVTTL, 1.8V, 1.8V
D:		5th Generation

S/D: 90balls FBGA

====== ###扩展底层板: Tiny6410SDK 增强版 - TinyADK 1312B

Button:		K1 - XEINT16
			K2 - XEINT17
			K3 - XEINT18
			K4 - XEINT19
			Button IO接上拉电阻，按下按键后IO为拉为低电平;
Buzzer:		XpwmTOUT0 (XpwmTOUT0/XCLKOUT/GPF14)
I2C-EEPROM:	ATMLH346
			Xi2cSCL0, Xi2cSDA0

###FriendlyARM Tiny6410 下载程序 - MiniTools.exe

底层板S2选择NAND启动方式
按住K1按钮，打开电源开关S1
此时若串口连接COM0到PC，配置波特率为115200，就可以看到串口输出消息; 不进行串口连接，也可以在液晶屏上看到同样的消息;

输出消息:

 Booting from NAND

 Superboot6410
 Ver: 141011
 CPU: S3C6410 533MHz
 RAM: 256MB
 NAND: 1GB(SLC) ID:ECD35195
 Touch Device: 1-wire
 LCD Type: S70(Auto)

 USB Mode: Waiting...
 Hello USB Loop

底层板通过USB与PC连接，PC识别USB设备。打开MiniTools.exe软件，识别到ARM开发板;
同时串口输出消息:
```
 USB Mode: Connected
```
选择不同模式，下载程序;

注意：必须先给板子上电，然后在打开MiniTools.exe, 否则MiniTools.exe会卡死无响应。

###FriendlyARM Tiny6410 下载程序 - SDHC

SD-Boot

elvischen/ARM-Tiny6410

FriendlyARM - Tiny6410