wiringOP-for-MangoPi-H616: A C repository from enadata

说明

本仓库是将 wiringOP 移植到 MangoPi(H616) 上。需要使用 Orange Pi Zero2的对应的系统镜像。

下载

apt-get update
apt-get install -y git
git clone https://github.com/liuls2002/wiringOP-for-MangoPi-H616.git

编译安装

cd wiringOP
./build clean
./build

Python版本

# 下载 orangepi 提供的代码
git clone --recursive https://github.com/orangepi-xunlong/wiringOP-Python.git
cd wiringOP-Python

# 使用本工程中的代码替换 wiringOP-Python 目录下的 wiringOP
cp -r ./wiringOP ./wiringOP-Python

# 安装tools
sudo apt-get install swig python3-dev python3-setuptools

# Build & install with
python3 generate-bindings.py > bindings.i
sudo python3 setup.py install

Mango Pi的官方网站

Mango Pi official website | Tiny and Elegant SBC | mqquad

相较于 Orange Pi 提供的代码的改动

Mango Pi(h616) 与 Orange Pi Zero2 使用相同的soc（全志H616），所以基于 Orange Pi Zero2 进行移植修改比较方便。

Mango Pi(h616) 引脚对应关系如下：

总共有3种编号：board引脚编号，芯片引脚编号，逻辑引脚编号。控制gpio时一般采用逻辑引脚编号。

==我们需要修改这3者的映射关系。为了简便，我将逻辑引脚编号与board的引脚编号保持一致，使用时需要注意。==

1 修改 gpio/OrangPi.c

将#ifdef CONFIG_ORANGEPI_ZERO2包含的代码替换为如下代码：

#ifdef CONFIG_ORANGEPI_ZERO2
int pinToGpioOrangePi [64] =
{
    -1,  // 0
    -1 , -1 ,
    264 , -1 ,
    263 , -1 ,
    256 , 224 ,
    -1 , 225 ,
    226 , 257 ,
    227 , -1 ,
    269 , 270 ,
    -1 , 228 ,
    231 , -1 ,
    232 , 262 ,
    230 , 229 ,
    -1 , 233 ,
    266 , 265 ,
    267 , -1 ,
    268 , 261 ,
    271 , -1 ,
    258 , 234 ,
    272 , 260 ,
    -1 , 259 , // 40
    -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, 
    -1, -1, -1, -1,-1, // 63
};

int physToWpi[64] =
{
	-1,		// 0
	-1, -1,	// 1, 2
	3, -1,  //3, 4
	5, -1,  //5, 6
	7, 8,  //7, 8
	-1, 10, //9,10
	11, 12, //11,12
	13, -1, //13,14
	15, 16, //15,16
	-1, 18, //17,18
	19, -1, //19,20
	21, 22, //21,22
	23, 24, //23, 24
	-1, 26,	// 25, 26
	27, 28,   //27, 28
	29, -1,	//29, 30
	31, 32,	//31, 32
	33, -1, //33, 34
	35, 36, //35, 36
	37, 38, //37, 38
	-1, 40, //39, 40
	// Padding:
	-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,	// ... 56
	-1, -1, -1, -1, -1, -1, -1,	// ... 63
};

char *physNames[64] =
{
  NULL,
  "     3.3V", "5V      ",
  " TWI1_SDA", "5V      ",
  " TWI1_SCL", "GND     ",
  "I2S0_MCLK", "TX0",
  "      GND", "RX0",
  "      TX5", "I2S_CLK",
  "      RX5", "GND     ",
  " TX4/PWM3", "RX4/PWM4",
  "     3.3V", "PH4",
  "SPI1_MOSI", "GND     ",
  "SPI1_MISO", "RX2",
  " SPI1_CLK", "SPI1_CS0 ",
  "      GND", "SPI1_CS1",
  " TWI2_SDA", "TWI2_SCL",
  "     PI11", "GND     ",
  "     PI12", "LEDC/TX2",
  "     PI15", "GND     ",
  "I2S0_LRCK", "PH10",
  "     PI16", "I2S0_DOUT",
  "      GND", "I2S0_DIN",
       NULL, NULL,
       NULL, NULL,
       NULL, NULL,
       NULL, NULL,
       NULL, NULL,
  	   NULL, NULL,
       NULL, NULL,
       NULL,NULL,NULL,NULL,NULL,NULL,NULL,NULL,NULL,
};
#endif

替换 void OrangePiReadAll(void)函数中的部分代码

// 替换前
#elif CONFIG_ORANGEPI_ZERO2
	for (pin = 1 ; pin <= 34; pin += 2)   // orangepi zero2 引出34pin
// 替换后
#elif CONFIG_ORANGEPI_ZERO2
	for (pin = 1 ; pin <= 40; pin += 2)   // mangopi 引出40pin

2 修改 wiringPi/OrangePi.c