This is a DMX512 custom component for ESPHome that allows Arduino-based devices to control DMX devices via UART (this requires an RS485 module, see below).
The implementation is based on other projects:
It differs in that it uses the internal UART component but generates the break signal by detaching and re-attaching the GPIO pin (on ESP32).
DMX only works on hardware UARTs, therefore the number of the UART in use needs to be set. This defaults to 1, as the first UART is usually used for logging purposes.
On the ESP8266, the only pin you can use is GPIO2. It's TX-only and can easily be used for DMX.
See the provided example file for a complete example, including output and light components. For the dmx512 component, some options need additional explanation:
dmx512:
id: dmx
uart_id: uart_bus
enable_pin: GPIO33
tx_pin: GPIO5
uart_num: 1
periodic_update: true
force_full_frames: false
custom_break_len: 92
custom_mab_len: 12
update_interval: 500
id: The ID of this DMX512 hubuart_id: Set this to the ID of your UART componentenable_pin: Set this to the pin number the MAX585 enable pins are connected to. Optionaltx_pin: Set this to the same pin number as the UART component. This is required for the generation of the break signal. Defaults to GPIO5.uart_num: Set this to the internal ESP32 UART number. If only logging is configured, this should be set to 1 (default).periodic_update: If set to false, only state changes are transmitted and the bus is silent in between - violates the specification and may cause some dimmers to turn offforce_full_frames: If set to true, the full 513-byte frame is always sent. Otherwise, only the configured channels are transmitted.custom_mab_len: Set a custom mark-after-break length (in uS, default 12)custom_break_len: Set a custom break length (in uS, default 92)update_interval: Specify a custom update interval, i.e. the minimum time between resending the current values (in ms, default 500)
Outputs point to channels in the DMX universe, from 1 to 512.
Some DMX fixtures can be daisy chained with XLR cables, and each one can be set to operate at a different address. When you specify the output channel in the configuration of this component, take into account that channel (in esphome component) = address + channel (on the fixture).
When you choose addresses for your DMX fixtures keep in mind that the next free address number on the bus that can be assigned is the address of the previous light + the last channel number of that light.
For easier understanding, eg. the ADJ VBar Pak can be used in various modes. When you have 4 of these daisy chained, if you set them up to 8-channel mode (to access all the effects) you can set the address of the first one to 1, the next one to 9, the third one to 17, fourth one to 25, using the buttons on each fixture.
Then in the config you'd have channels for the first one from 1 to 8, the second one from 9 to 16, third one from 17 to 24, forth one from 25 to 32.
See another example for this kind of configuration.
The output implements float values between 0 and 100. You can use it not only for light, but for any component which can send data to it, moreover, it can be set from lambdas.
The above example shows use cases for this, where certain outputs are used for hardware effects selection on the DMX fixture, using a select component, and parameters can be adjusted from number entities.
Tip: Usage of gamma_correct: 0 in the lights configuration is likely required for most fixtures, as the gamma compensation is usually already done in their hardware. This can be observed when, without this setting set to 0, dimming to around 10% will actually turn the lights off. ESPHome has gamma_correct set to 2.8 by default.
Some fixtures support 16 bit outputs. Usually, two adjacent DMX channels are used for this. You can achieve such an effect by creating a template-output and using a lambda function for writing the state to your outputs. The example below uses channel 1 and 2 for a combined 16 bit output:
output:
- platform: dmx512
channel: 1
universe: dmx
id: coarse_red
- platform: dmx512
channel: 2
universe: dmx
id: fine_red
- platform: template
id: red_output
type: float
min_power: 0.01
write_action:
- lambda: |-
int lvl = static_cast<int>(state*65535.0);
uint8_t low = lvl & 0xff;
uint8_t high = (lvl >> 8);
id(coarse_red).set_level(high/255.0);
id(fine_red).set_level(low/255.0);
You can use an RS485-TTL adapter module to connect your ESP device with the DMX bus. Attention: Some modules are actually 5V modules, but seem to work fine even if powered from 3.3V. However, there is no guarantee the MAX485 works at 3.3V. To be on the safe side, Use the MAX3485 instead (which is the equivalent for 3.3V). NEVER power the module by 5V, the ESP is not designed for 5V logic!
For this adapter, use the wiring below:
MAX485-M VCC -> ESP +3.3V
MAX485-M GND -> ESP GND
MAX485-M DE -> ESP +3.3V
MAX485-M RE -> not connected
MAX485-M DI -> ESP32 GPIO5 or ESP8266 GPIO2 (as per examples above)
MAX485-M A -> XLR 3 (DMX +)
MAX485-M B -> XLR 2 (DMX -)
MAX485-M GND -> XLR 1 (DMX GND)
The RE pin can be left unconnected, since we do not want to receive anything from the bus. For this module, you could even leave DE unconnected since there is a pull-up resistor on the board.
Don't forget about 120Ohm termination resistors (the specific module above already has the 120Ohm resistor as R7 on the board). If your fixture has DMX IN and OUT ports, on the OUT port of the last fixture in the chain you should use a termination resistor between XLR pins 2 and 3. Similarly on MAX485-M, it has to be placed in parallel with A and B outputs, given that it's going to be placed at the start of the chain.
Using good quality 120Ohm impedance cables, DMX lines can be run a maximum distance of approximately 1000 meters. With CAT5 cable DMX lines are safe until approximately 300 meters.
You can also tie the DE pin to a GPIO of the ESP. Usually, you would configure this GPIO as enable_pin in the DMX component to activate the module automatically.
If you want to have a "mute" switch instead, define it as a switch instead and do not configure enable_pin in the DMX component:
switch:
- platform: gpio
name: 'DMX output MUTE'
icon: mdi:lightbulb-off
pin:
number: GPIO13
inverted: true