pymcuprog - Python MCU programmer

pymcuprog is a Python utility for programming various Microchip MCU devices using Microchip CMSIS-DAP based debuggers

Install using pip from pypi:

pip install pymcuprog

Browse source code on github

Read API documentation on github

Read the changelog on github

Usage

pymcuprog can be used as a command-line interface or a library

CLI help

For more help with using pymcuprog CLI see help

CLI examples

When installed using pip, pymcuprog CLI is located in the Python scripts folder.

Test connectivity by reading the device ID using Curiosity Nano:

pymcuprog ping

Erase memories then write contents of an Intel(R) hex file to flash using Curiosity Nano (pymcuprog does NOT automatically erase before writing):

pymcuprog erase
pymcuprog write -f app.hex

Erase memories and write an Intel hex file (using the --erase switch):

pymcuprog write -f app.hex --erase

Erase memories, write an Intel hex file and verify the content:

pymcuprog write -f app.hex --erase --verify

Serial port UPDI (pyupdi)

The AVR UPDI interface implements a UART protocol, which means that it can be used by simply connecting TX and RX pins of a serial port together with the UPDI pin; with a series resistor (eg: 1k) between TX and UPDI to handle contention. (This configuration is also known as "pyupdi".) Be sure to connect a common ground, and use a TTL serial adapter running at the same voltage as the AVR device.

                        Vcc                     Vcc
                        +-+                     +-+
                         |                       |
 +---------------------+ |                       | +--------------------+
 | Serial port         +-+                       +-+  AVR device        |
 |                     |      +----------+         |                    |
 |                  TX +------+   1k     +---------+ UPDI               |
 |                     |      +----------+    |    |                    |
 |                     |                      |    |                    |
 |                  RX +----------------------+    |                    |
 |                     |                           |                    |
 |                     +--+                     +--+                    |
 +---------------------+  |                     |  +--------------------+
                         +-+                   +-+
                         GND                   GND

pymcuprog includes this implementation as an alternative to USB/EDBG-based tools. To connect via a serial port, use the "uart" tool type with the UART switch in addition.

Example: checks connectivity by reading the device identity

pymcuprog ping -d avr128da48 -t uart -u com35

For more examples see pymcuprog on pypi.org

Library usage example

pymcuprog can be used as a library using its backend API. For example:

"""
Example usage of pymcuprog as a library to read the device ID
"""
# pymcuprog uses the Python logging module
import logging
logging.basicConfig(format="%(levelname)s: %(message)s", level=logging.WARNING)

# Configure the session
from pymcuprog.backend import SessionConfig
sessionconfig = SessionConfig("atmega4808")

# Instantiate USB transport (only 1 tool connected)
from pymcuprog.toolconnection import ToolUsbHidConnection
transport = ToolUsbHidConnection()

# Instantiate backend
from pymcuprog.backend import Backend
backend = Backend()

# Connect to tool using transport
backend.connect_to_tool(transport)

# Start the session
backend.start_session(sessionconfig)

# Read the target device_id
device_id = backend.read_device_id()
print ("Device ID is {0:06X}".format(int.from_bytes(device_id, byteorder="little")))

Supported devices and tools

pymcuprog is primarily intended for use with PKOB nano (nEDBG) debuggers which are found on Curiosity Nano kits and other development boards. This means that it is continuously tested with a selection of AVR devices with UPDI interface as well as a selection of PIC devices. However since the protocol is compatible between all EDBG-based debuggers (pyedbglib) it is possible to use pymcuprog with a wide range of debuggers and devices, although not all device families/interfaces have been implemented.

Debuggers / Tools

pymcuprog supports:

PKOB nano (nEDBG) - on-board debugger on Curiosity Nano
MPLAB PICkit 4 In-Circuit Debugger (when in 'AVR mode')
MPLAB Snap In-Circuit Debugger (when in 'AVR mode')
Atmel-ICE
Power Debugger
EDBG - on-board debugger on Xplained Pro/Ultra
mEDBG - on-board debugger on Xplained Mini/Nano
JTAGICE3 (firmware version 3.0 or newer)

Although not all functionality is provided on all debuggers/boards. See device support section below.

Devices