firmata/ConfigurableFirmata

Issues

• Feature Request: 433 Mhz tx/rx support

  #68 opened 7 years ago
  16

• Feature Request: Firmware reports limitations

  #66 opened 8 years ago
  2

• Create a new Servo 2.0 that is decoupled from AnalogWrite

  #65 opened 8 years ago
  1

• apply Firmata updates

  #64 opened 8 years ago
  1

• Not working without Serial USB connection?

  #62 opened 8 years ago
  5

• stepperConfig causes communication failure with Arduino

  #60 opened 8 years ago
  9

• Using stepper deceleration breaks callback functionality

  #59 opened 8 years ago
  7

• If user had installed v2.9.0 a couple of months ago, they can't install new v2.9.0

  #58 opened 8 years ago
  1

• Need to add license information

  #54 opened 8 years ago
  5

• Do not include <SoftwareSerial.h> unless the user wants it.

  #53 opened 8 years ago
  5

• Watchdog for Firmata

  #47 opened 9 years ago
  5

• Can't get PIN_MODE_PULLUP working

  #45 opened 9 years ago
  10

• Network configuration for Heroku

  #44 opened 8 years ago
  21

• add a NewPing wrapper as a contributed feature

  #43 opened 9 years ago
  7

• serial receive prevents reconnect to host

  #37 opened 9 years ago
  58

• Add DHT sensor support as a contributed feature

  #36 opened 3 years ago
  1

• expose board-specific hardware via add-ons

  #35 opened 9 years ago
  0

• add step delay to StepperFirmata

  #34 opened 9 years ago
  1

• Update Stepper to wrap AccelStepper

  #33 opened 7 years ago
  15

• allow servo to use full range of pins, including analog

  #32 opened 9 years ago
  0

• merge in updates from Firmata 2.5

  #29 opened 9 years ago
  1

• Add Arduino pluggable usb midi to ConfigurableFirmata

  #28 opened 9 years ago
  5

• Timer-driven stepper implementation

  #27 opened 9 years ago
  17

• Stepper motor library homing/limit capability

  #26 opened 9 years ago
  11

• Enable servo to be attached to pins numbered higher than 15

  #25 opened 9 years ago
  1

• Can not compile with teensy 3.1

  #22 opened 9 years ago
  6

• Connection issue

  #21 opened 9 years ago
  5

• ConfigurableFirmata.h: No such file or directory

  #20 opened 9 years ago
  1

• ATH0

  #19 opened 10 years ago
  3

• Is there a reason "set digital pin value", 0xF5 from protocol spec is not implemented?

  #18 opened 10 years ago
  2

• create a Device ID scheme

  #16 opened 8 years ago
  10

• Consider separating the concept of pin modes and configuration

  #15 opened 8 years ago
  5

• replace error strings with error codes

  #14 opened 10 years ago
  0

• consolidate FirmataExt and FirmataReporting into ConfigurableFirmata class

  #13 opened 10 years ago
  1

• create new sysex-based implementation of ServoFirmata

  #12 opened 10 years ago
  0

• remove 3rd party libraries

  #11 opened 10 years ago
  2

• Servo not working on pins above 11 or 15 (depending on board) in Configurable Firmata

  #10 opened 9 years ago
  20

• Add shift feature class to configurable branch

  #9 opened 10 years ago
  0

• Add pulseIn/pulseOut feature class to configurable branch

  #8 opened 10 years ago
  0

• create online build tool/service for ConfigurableFirmata

  #7 opened 9 years ago
  2

• Reduce dynamic allocation in ConfigurableFirmata

  #6 opened 10 years ago
  0

• ConfigurableFirmata RAM usage

  #5 opened 10 years ago
  0

• send error message if dynamic memory allocation fails

  #4 opened 10 years ago
  0

• Stepper motor library homing/limit capability

  #3 opened 9 years ago
  1

• stepper motor library feedback to pc

  #2 opened 7 years ago
  23

• need a concept to handle Configurable Features that depend on third-party libraries

  #1 opened 8 years ago
  16