spi-device

SPI serial bus access with Node.js on Linux boards like the Raspberry Pi or BeagleBone. All methods have asynchronous and synchronous forms.

spi-device supports Node.js versions 10, 12, 14, 15 and 16.

Installation
Usage
API Documentation

Installation

npm install spi-device

Usage

Determine the temperature using a TMP36 analog temperature sensor wired to channel 5 on an MCP3008 SPI A/D converter.

const spi = require('spi-device');

// The MCP3008 is on bus 0 and it's device 0
const mcp3008 = spi.open(0, 0, err => {
  // An SPI message is an array of one or more read+write transfers
  const message = [{
    sendBuffer: Buffer.from([0x01, 0xd0, 0x00]), // Sent to read channel 5
    receiveBuffer: Buffer.alloc(3),              // Raw data read from channel 5
    byteLength: 3,
    speedHz: 20000 // Use a low bus speed to get a good reading from the TMP36
  }];

  if (err) throw err;

  mcp3008.transfer(message, (err, message) => {
    if (err) throw err;

    // Convert raw value from sensor to celcius and log to console
    const rawValue = ((message[0].receiveBuffer[1] & 0x03) << 8) +
      message[0].receiveBuffer[2];
    const voltage = rawValue * 3.3 / 1023;
    const celcius = (voltage - 0.5) * 100;

    console.log(celcius);
  });
});

spi-device enables low-level access to SPI devices. Often, high-level access is required. When this is the case, high-level packages can be built using spi-device. An example of such a package is mcp-spi-adc which provides a high-level API for accessing an MCP3008 SPI A/D converter and will generally be more useful than the low-level demonstration code shown above.

API Documentation

All methods have asynchronous and synchronous forms.

The asynchronous form always take a completion callback as its last argument. The arguments passed to the completion callback depend on the method, but the first argument is always reserved for an exception. If the operation was completed successfully, then the first argument will be null or undefined.

When using the synchronous form any exceptions are immediately thrown. You can use try/catch to handle exceptions or allow them to bubble up.

open(busNumber, deviceNumber[, options], cb)

busNumber - the number of the SPI bus to open, 0 for /dev/spidev0.n, 1 for /dev/spidev1.n, ...
deviceNumber - the number of the SPI device to open, 0 for /dev/spidevn.0, 1 for /dev/spidevn.1, ...
options - an optional object specifying device configuration options
cb - completion callback

Asynchronous open. Returns a new SpiDevice object. The completion callback gets one argument (err). The SpiDevice object returned should not be used before the completion callback is called.

openSync(busNumber, deviceNumber[, options])

busNumber - the number of the SPI bus to open, 0 for /dev/spidev0.n, 1 for /dev/spidev1.n, ...
deviceNumber - the number of the SPI device to open, 0 for /dev/spidevn.0, 1 for /dev/spidevn.1, ...
options - an optional object specifying device configuration options

Synchronous open. Returns a new SpiDevice object.

device.transfer(message, cb)

message - an array of one or more read+write transfers
cb - completion callback

Asynchronous message transfer. An SPI message is an array of one or more read+write transfers. The completion callback gets two arguments (err, message). Returns this.

device.transferSync(message)

message - an array of one or more read+write transfers

Synchronous message transfer. An SPI message is an array of one or more read+write transfers. Returns this.

device.getOptions(cb)

cb - completion callback

Asynchronously read device configuration options. The completion callback gets two arguments (err, options) where options is an object describing the device configuration options. Returns this.

device.getOptionsSync()

Synchronously read device configuration options. Returns an object describing the device configuration options.

device.setOptions(options, cb)

options - an object specifying device configuration options
cb - completion callback

Asynchronously write device configuration options. The completion callback gets one argument (err). Returns this.

device.setOptionsSync(options)

options - an object specifying device configuration options

Synchronously write device configuration options. Returns this.

device.close(cb)

cb - completion callback

Asynchronous close. Frees system resources used by this instance. The completion callback gets one argument (err). Returns null.

device.closeSync()

Synchronous close. Frees system resources used by this instance. Returns null.

MODE0

SPI mode number 0.

MODE1

SPI mode number 1.

MODE2

SPI mode number 2.

MODE3

SPI mode number 3.

Message

An SPI message is an array of one or more read+write transfers. A transfer is an object with the properties listed below. Most of the properties are optional. Note that although both sendBuffer and receiveBuffer are optional, at least one one of them must be specified.

byteLength - number, 32-bit, the number of bytes to transfer
sendBuffer - optional Buffer, transmit data
receiveBuffer - optional Buffer, receive data
speedHz - optional number, 32-bit, override of the device's clock frequency in Hertz
microSecondDelay - optional number, 16-bit, delay after the last bit transfer before optionally deselecting the device before the next transfer, default 0
bitsPerWord - optional number, 8-bit, override of the device's wordsize
chipSelectChange - optional boolean, true to deselect device before starting the next transfer, default false

Configuration Options

Device configuration options can be optionally specified when a device is opened with the open or openSync methods. They can also be specified at a later point with the setOptions or setOptionsSync methods. When calling these methods, only the options that need to be set need to be specified in the options object passed to those methods. All options are optional and the appropriate defaults will be used for options that are not specified.

The options supported varies from system to system and will depend on the device drivers used on those systems.

Configurations options can be read with the getOptions and getOptionsSync methods.

IMPORTANT The semantics of chipSelectHigh have changed with Linux kernel 5. To the best of my knowledge, the chipSelectHigh option no longer serves any purpose when used from user space with Linux kernel 5 and should not be used. With Linux kernel 5, the chip select is assumed to be active low. With Linux kernel 5, if an SPI device has has active high chip select, it's chip select must be controlled manually with a GPIO using a module such as onoff. The chipSelectHigh option has been crossed out below but it's still available for usage on older kernels.

mode - number, 2-bit, MODE0, MODE1, MODE2, or MODE3, default MODE0
~~chipSelectHigh - boolean, true for active high chip select, default false~~
lsbFirst - boolean, true for least significant bit first transfer, default false
threeWire - boolean, true for shared MISO/MOSI signals, default false
loopback - boolean, true for loopback mode, default false
noChipSelect - boolean, true for 1 device per bus, no chip select, default false
ready - boolean, true if device pulls low to pause, default false
bitsPerWord - number, 8-bit, device word size, default 8
maxSpeedHz - number, 32-bit, device clock frequency in Hertz, default system specific

fivdi/spi-device