fra589/grbl-Mega-5X

Issues

• want to remap z axis step and direction pi

  #311 opened 2 years ago
  6

• Will not compile, homing cycles not defined.

  #310 opened 6 months ago
  3

• Cloned X and Y Axis: Normal movement fine but only one motor runs during homing

  #309 opened 2 years ago
  6

• servo 0-5V

  #305 opened 2 years ago
  3

• GRBL Plotter Commands

  #304 opened 2 years ago
  5

• Homing dual axis

  #303 opened 2 years ago
  2

• Cant set steps on y axis

  #301 opened 2 years ago
  6

• Hominng problem

  #300 opened 2 years ago
  10

• Auto gantry squaring

  #293 opened 2 years ago
  9

• [Solved] Grbl Reset on C axis reverse moves - Triple check pin and port defination in cpu_map

  #292 opened 2 years ago
  4

• Need clarity on homing.

  #291 opened 2 years ago
  8

• Axes move incorrectly (wrong direction) after changing step/mm parameters.

  #290 opened 2 years ago
  2

• Some new grbl settings don't have a name (comment) on the grbl console

  #289 opened 2 years ago
  1

• Dual Y axis motor, one motor moves backward momentarily before moving correctly upon jogging

  #288 opened 2 years ago
  10

• mega5x hotwire

  #285 opened 2 years ago
  5

• Error in digital_control.c

  #283 opened 2 years ago
  1

• Digital Inputs add M66 "Wait on Input" GCode

  #282 opened 2 years ago
  10

• motors off

  #279 opened 2 years ago
  3

• Cloned Y Axis moving under normal G0 command, but not while homing

  #278 opened 2 years ago
  6

• pwm pin d2

  #274 opened 3 years ago
  1

• Changing x-max (limit) pin as a-min (limit) pin

  #272 opened 2 years ago
  4

• Dual Y-Axis Motors (One is working where other is not)

  #271 opened 3 years ago
  6

• THC Support

  #268 opened 3 years ago
  1

• Wiring diagram errors?

  #261 opened 3 years ago
  5

• Setting up a z axis touch plate - which pin do I use?

  #260 opened 3 years ago
  1

• PWM does not work

  #257 opened 3 years ago
  3

• Wrong movements while running

  #254 opened 3 years ago
  5

• Serial.c --- volatile wrong way around on serial_rx indicies

  #253 opened 3 years ago
  2

• Invert Spindle PWM

  #252 opened 3 years ago
  4

• G code doesnt run

  #249 opened 3 years ago
  13

• Invert control pin

  #248 opened 3 years ago
  1

• compiling error

  #245 opened 3 years ago
  5

• G2 G3 command from Fusion360

  #242 opened 3 years ago
  5

• Cycle start button

  #239 opened 3 years ago
  4

• A axis not working.

  #238 opened 3 years ago
  5

• Laser control Pinout

  #234 opened 3 years ago
  2

• Digital or maybe even analogue inputs via the USB interface ?

  #233 opened 3 years ago
  5

• No output on D11 in laser mode

  #232 opened 3 years ago
  2

• ENDSTOPs not working

  #230 opened 3 years ago
  2

• Resuming after a door/alarm state resets M7 (Coolant) state

  #229 opened 3 years ago
  15

• Machine locked during program execution

  #225 opened 3 years ago
  8

• MKS GEN-L V1.0 D42 end-stop

  #223 opened 3 years ago
  5

• Dual y axis speed issue

  #222 opened 3 years ago
  4

• Square Homing issue, Is not going right

  #221 opened 3 years ago
  4

• Dual Y Axis

  #220 opened 3 years ago
  1

• avrdude: stk500v2_ReceiveMessage(): timeout

  #219 opened 3 years ago
  3

• Wrong state RUN when jogging right after probing

  #214 opened 3 years ago
  5

• Grbl functions without serial.

  #213 opened 3 years ago
  1

• Disable Steppers causing EXEC_RESET on RAMPS v1.4

  #211 opened 3 years ago
  1

• ENABLE_SAFETY_DOOR_INPUT_PIN question

  #210 opened 3 years ago
  3