fra589/grbl-Mega-5X

Issues

• Hard limit and homing ramps don´t working

  #380 opened 2 months ago by xero83
  2

• gestion changeur outil

  #372 opened 4 months ago by supernono-fr
  1

• Soft limits will not allow A Axis movement in any positive direction

  #374 opened 4 months ago by CNCWoodworker
  2

• not working

  #377 opened 4 months ago by parkgeonhun
  1

• Extra digital outputs?

  #378 opened 4 months ago by DDanielMK
  8

• How do I resolve this error? A axis and B axis do not work

  #376 opened 5 months ago by parkgeonhun
  1

• mega 2560 5x Stepper motor does not move

  #375 opened 5 months ago by parkgeonhun
  3

• Code error in motion_control.c?

  #371 opened 6 months ago by ccwtruck
  2

• Cannot control with UGS or Openbuild control software

  #334 opened 6 months ago by Zjokkeh
  3

• homing limit switches not stopping motors

  #339 opened 6 months ago by markusca
  13

• is frequently change $ value will worn out EEPROM?

  #348 opened 6 months ago by ariefadha
  2

• I need some help

  #350 opened 6 months ago by srmarkovic
  2

• Duplicate Axis Issues

  #355 opened 6 months ago by Mitchell128134
  6

• PROBLEME de connexion avec arduino mega

  #357 opened 6 months ago by franck70150
  6

• Compatibilidad Mega + GRBL

  #363 opened 6 months ago by IgnacioZeus
  1

• alarm 11, why and what to do with it?

  #367 opened 6 months ago by Krasti3049
  4

• $103 parameter not working as expected.

  #370 opened 6 months ago by CNCWoodworker
  8

• Cannot use RAMPS configuration with my build...

  #369 opened 6 months ago by ccwtruck
  19

• Driver enable delay before moving

  #364 opened 6 months ago by adrianopedro
  3

• Acceleration is ignored with cloned axis

  #340 opened a year ago by gpstone
  8

• Laser pin pinout (sorry to ask again)

  #361 opened 10 months ago by GeoffreyOlivier
  16

• PWM on D8

  #354 opened 10 months ago by Zjokkeh
  2

• No delay after command M3 to keep time "pen down"

  #362 opened 10 months ago by Srallie
  19

• does not display the home status during the home loop

  #358 opened a year ago by shura-2
  1

• Setting values for axis does not set values

  #353 opened a year ago by sfmissionmark
  1

• b-axis configuration

  #329 opened a year ago by sfmissionmark
  3

• Homing cycle doesn't finish x homing

  #349 opened a year ago by gustavoriverag
  6

• emergency button

  #347 opened a year ago by ariefadha
  4

• Cann't use Servo motor MG90S 180degree

  #343 opened a year ago by akkarawat2000
  19

• Clonned Y axis will home under $HY, but won't under $H

  #346 opened a year ago by ContinenteCNC
  1

• Open-source?

  #345 opened a year ago by mileticveljko
  1

• 5v stepper motor 28BYJ-48 can use in X-Axis in Ramp Board v 1.5 ?

  #344 opened a year ago by akkarawat2000
  7

• Changing homing order

  #342 opened a year ago by DonArkon
  4

• Voltage requirement: Limit Switch

  #337 opened 2 years ago by milesmiles902
  2

• Another homing issue

  #336 opened 2 years ago by Zjokkeh
  40

• Limit Switch Logic

  #333 opened 2 years ago by milesmiles902
  4

• Questions about using 4 axis and 5 motos without the ramps shield.

  #332 opened 2 years ago by rbp9802
  2

• $20 seems error

  #331 opened 2 years ago by ariefadha
  0

• invert function of the limit switch

  #330 opened 2 years ago by hamelsveld
  9

• Can't connect to grblgru software

  #327 opened 2 years ago by ariefadha
  23

• RC-Servo on Spindle PWM?

  #323 opened 2 years ago by svenhb
  3

• Spindle PWM signal not working in Arduino Mega 2560 and ramps 1.4.

  #322 opened 2 years ago by Girishking
  1

• Reset and lost parameters with six axes

  #321 opened 2 years ago by jjnicholls
  2

• $27 - Homing pull-off, mm

  #320 opened 2 years ago by ariefadha
  4

• question: will work for 3d printer?

  #319 opened 2 years ago by ariefadha
  1

• question about rotary

  #318 opened 2 years ago by ariefadha
  8

• 3018 cutter comp

  #317 opened 2 years ago by mg-jones-uk
  2

• Streaming GCode Program -> Error 25 + 2

  #312 opened 2 years ago by fra589
  1

• renaming axis from software

  #314 opened 2 years ago by ariefadha
  1

• Question for #define N_AXIS_LINEAR

  #313 opened 2 years ago by ariefadha
  2