gaudat/eggbotcode

Issues

• Line breaks here (eggbot_hatch.inx) made the extension not load for me.

  #85 opened 9 years ago by GoogleCodeExporter
  6

• IMPORTANT: Please use GitHub for reporting new issues.

  #86 opened 9 years ago by GoogleCodeExporter
  0

• svg image is fliped

  #84 opened 9 years ago by GoogleCodeExporter
  1

• Manual moves above 1000 steps/s fail.

  #81 opened 9 years ago by GoogleCodeExporter
  1

• build-concorde-osx-0_2.sh script outdated

  #82 opened 9 years ago by GoogleCodeExporter
  0

• Allow manual moves with greater than 3200 steps (egg axis)

  #83 opened 9 years ago by GoogleCodeExporter
  1

• EBB firmware - for v2.2.4 and above, revert to v2.0.1 <duration> units

  #79 opened 9 years ago by GoogleCodeExporter
  6

• For EBB - add Abort command - to stop long moves

  #80 opened 9 years ago by GoogleCodeExporter
  1

• EBB firmware - document the "QB" command in EBB commands documentation

  #78 opened 9 years ago by GoogleCodeExporter
  1

• code issue

  #76 opened 9 years ago by GoogleCodeExporter
  2

• EBB v2.2.3 has min and max servo positions reversed

  #77 opened 9 years ago by GoogleCodeExporter
  1

• EBB slow motor rotation jerky.

  #75 opened 9 years ago by GoogleCodeExporter
  3

• Users report step speeds above 1000 steps/s result in erratic motor operation

  #73 opened 9 years ago by GoogleCodeExporter
  2

• Invalid comparison between string and number for viewbox determination in eggbot.py

  #74 opened 9 years ago by GoogleCodeExporter
  1

• QC command errors out after 69 times in v2.0.1 of EBB firmware

  #71 opened 9 years ago by GoogleCodeExporter
  2

• Add raise/lower pen option to Layers tab of Eggbot Control

  #72 opened 9 years ago by GoogleCodeExporter
  1

• EBB: Create separate set of commands that use 'correct' ms <duration> values, revert SM, SP, TP commands

  #69 opened 9 years ago by GoogleCodeExporter
  1

• Remove "empty" XML parameters in contributed extensions

  #70 opened 9 years ago by GoogleCodeExporter
  1

• Update EBB S2 documentation with new format (v2.1.5 and above)

  #67 opened 9 years ago by GoogleCodeExporter
  1

• EBB SE command PWM does not work in 2.2.1 and below

  #68 opened 9 years ago by GoogleCodeExporter
  1

• The SP command <duration> parameter does not default to 500ms

  #65 opened 9 years ago by GoogleCodeExporter
  1

• SP command happens at end of <duration> not at beginning

  #66 opened 9 years ago by GoogleCodeExporter
  2

• <duration> values (for SM, SP and TP commands) do not allow over 2,621ms or the delay isn't right

  #63 opened 9 years ago by GoogleCodeExporter
  1

• SP and TP commands do not have proper delay

  #64 opened 9 years ago by GoogleCodeExporter
  1

• Hershey Text causes Inkscape Trunk to crash

  #62 opened 9 years ago by GoogleCodeExporter
  16

• USB Driver Failed to Install on Windows 8 (64 bit)

  #60 opened 9 years ago by GoogleCodeExporter
  4

• USB Driver Failed to Install on Windows 8 (64 bit)

  #61 opened 9 years ago by GoogleCodeExporter
  1

• EBB SE command does not create proper output in 2.1.5

  #59 opened 9 years ago by GoogleCodeExporter
  1

• Add simple limit switch inputs for stepper axes

  #57 opened 9 years ago by GoogleCodeExporter
  2

• StippleGen 2.02 does not run in Processing 2.0 beta 6

  #58 opened 9 years ago by GoogleCodeExporter
  1

• EBB SP command turns off other servo outputs

  #55 opened 9 years ago by GoogleCodeExporter
  1

• EBB: Add simple 'delay' command

  #56 opened 9 years ago by GoogleCodeExporter
  3

• eggbot_hatch.py problem

  #54 opened 9 years ago by GoogleCodeExporter
  15

• same track order problem in hatch on text object in inkscape using eggbot_hatch.py

  #53 opened 9 years ago by GoogleCodeExporter
  3

• Support 1600 total step/rev and 6400 step/rev plotter resolution

  #52 opened 9 years ago by GoogleCodeExporter
  4

• Egg measurements are difficult to predict

  #51 opened 9 years ago by GoogleCodeExporter
  3

• Fix permissions on Mac Installer

  #49 opened 9 years ago by GoogleCodeExporter
  4

• Can't pause or cancel the pattern

  #50 opened 9 years ago by GoogleCodeExporter
  1

• hatch does not work on Ubuntu

  #48 opened 9 years ago by GoogleCodeExporter
  5

• EBB PI command should only return 0 or 1

  #46 opened 9 years ago by GoogleCodeExporter
  2

• Remove copper from EBB mounting holes

  #47 opened 9 years ago by GoogleCodeExporter
  1

• EBB firmware: Error-trap too-fast speed reqests

  #45 opened 9 years ago by GoogleCodeExporter
  3

• Add velocity control mode to EBB firmware

  #43 opened 9 years ago by GoogleCodeExporter
  2

• EBB Firmware: Add long ints (4 bytes) for step counts

  #44 opened 9 years ago by GoogleCodeExporter
  3

• SVG <title> tag is not recognized; triggers "unable to draw object" warning

  #41 opened 9 years ago by GoogleCodeExporter
  1

• Ignore unsupported SVG elements unrelated to rendering; provide more informative warnings for other unsupported elements

  #42 opened 9 years ago by GoogleCodeExporter
  2

• Multi-layer plotting is very slow

  #39 opened 9 years ago by GoogleCodeExporter
  4

• Maze plotting requires high drawing precision for decent results

  #40 opened 9 years ago by GoogleCodeExporter
  1

• Firmware update program mphidflash does not work on ubuntu maverick

  #38 opened 9 years ago by GoogleCodeExporter
  6

• Read/act on limit switches

  #37 opened 9 years ago by GoogleCodeExporter
  6