Raspberry Pi Ansible Playbook

Glenn K. Lockwood, October 2018 - June 2021.

Introduction

This is an Ansible configuration that configures a fresh Raspbian installation on Raspberry Pi. It can be run in local (pull) mode, where ansible is running on the same Raspberry Pi to be configured, or standard remote mode. This playbook is known to run on Raspberry Pi OS 11.

Also included are plays for use with other single-board computers including NVIDIA Jetson Nano and BeagleBone Black.

Bootstrapping on Raspbian

You will need ansible installed on the Raspberry Pi being configured. This playbook relies on Ansible 2.8 or newer, which means you can no longer use sudo apt-get install ansible. Instead, you must

$ python3 -m venv --system-site-packages ansible_env

If this fails, you may need to:

$ sudo apt install python3-apt python3-virtualenv

Then activate the environment and install ansible:

$ source ./ansible_env/bin/activate

# Make sure that pip will install into our virtualenv
(ansible_env) $ which pip
/home/pi/src/git/rpi-ansible/ansible/bin/pip

# Install ansible and any other requirements
(ansible_env) $ pip install -r requirements.txt

Note that the Python 3.5 that ships with Debian 9.13 doesn't install pip when -m venv is used as above. It may be easier to simply use

$ pip3 install --user ansible

which pollutes your login Python environment, but is better than nothing.

Configuration

The contents of each file in host_vars/ is the intended configuration state for each Raspberry Pi. Look at one of the examples included to get a feel for the configurations available. Most variables should be optional, and if left undefined, do not enforce a specific configuration.

To add local users, create and edit roles/rpi/vars/users.yml. Follow the structure in roles/rpi/vars/users.yml.example. You can/should ansible-vault this file.

Using Remote Mode

Run one of the playbooks as you would do normally:

(ansible_env) $ ansible-playbook ./rpi.yml

The default hosts file and become_* configurations are set in ansible.cfg.

If you are bootstrapping a completely fresh system with the default users and hostnames, you may have to do the following:

Step 1: Add a config to ~/.ssh/config to map your intended hostname to the IP address of your fresh system. For example,

Host mynewrpi
    Hostname 192.168.1.101
    User pi

This allows, for example, ssh mynewrpi to work even if mynewrpi's hostname hasn't yet been from the default.

Step 2: ssh-copy-id mynewrpi to ensure passwordless SSH works to the new host. This will also make sure that your step 1 above was done correctly.

Step 3: Run the Ansible playbook to create new users and do most of the system configuration

Using Local Mode

Edit local.yml and add the mac address of eth0 for the Raspberry Pi to configure to the macaddrs variable. Its key should be a mac address (all lower case) and the value should be the short hostname of that system. Each such entry's short hostname must match a file in the host_vars/ directory.

Then run the playbook:

(ansible_env) $ ansible-playbook ./local.yml

The playbook will self-discover its settings, then idempotently configure the Raspberry Pi.

That said, it is better to use remote mode (so Ansible ssh'es into localhost) since that's what I most commonly test.

After running the playbook

This playbook purposely requires a few manual steps after running the playbook to ensure that it does not lock you out of your Raspberry Pi.

If using remote mode, delete the changes you made to ~/.ssh/config so that you switch to using the new user that Ansible created for subsequent Ansible connections.
While logged in as pi, sudo passwd glock (or whatever username you created) to set a password for that user. This is not required to log in as that user, but it is required to sudo as that user. You may also choose to set a password for the pi and/or root users.
usermod --lock pi to ensure that the default user is completely disabled.

You can also use the lock-default-user.yml standalone playbook to disable the default users for all the supported board-specific roles.

Optional configurations

SSH host keys

This playbook can install ssh host keys. To do so,

Drop the appropriate ssh_host_*_key files into roles/common/files/etc/ssh/
Rename each file from ssh_host_*_key to ssh_host_*_key.{{ ansible_hostname }}
ansible-vault encrypt roles/common/files/etc/ssh/ssh_host_*_key.*

The playbook will detect the presence of these files and install them.

Adding a new host to an existing role

In broad strokes, the process for adding a new host whose board-specific role already exists is

Add the new host to hosts.
Creating host_vars/newhost.yml and filling it out appropriately. It's easiest to start with an existing file for the same board type (e.g., cloverdale.yml for Raspberry Pi) and change it. Be sure to change the target_hostname variable at minimum.

Acknowledgment

I stole a lot of knowledge from https://github.com/giuaig/ansible-raspi-config/.

glennklockwood/rpi-ansible