/realsense-ros

Intel(R) RealSense(TM) ROS Wrapper for Depth Camera

Primary LanguagePythonApache License 2.0Apache-2.0

Intel® RealSense™

ROS2 packages for using Intel RealSense D400 cameras.
Latest release notes

rolling iron humble ubuntu22 ubuntu20

GitHubWorkflowStatus GitHubcontributors License

Table of contents

ROS1 and ROS2 Legacy

Intel RealSense ROS1 Wrapper Intel Realsense ROS1 Wrapper is not supported anymore, since our developers team are focusing on ROS2 distro.
For ROS1 wrapper, go to ros1-legacy branch
Moving from ros2-legacy to ros2-development
  • Changed Parameters:
    • "stereo_module", "l500_depth_sensor" are replaced by "depth_module"
    • For video streams: <module>.profile replaces <stream>_width, <stream>_height, <stream>_fps
      • ROS2-legacy (Old):
        • ros2 launch realsense2_camera rs_launch.py depth_width:=640 depth_height:=480 depth_fps:=30.0 infra1_width:=640 infra1_height:=480 infra1_fps:=30.0
      • ROS2-development (New):
        • ros2 launch realsense2_camera rs_launch.py depth_module.profile:=640x480x30
    • Removed paramets <stream>_frame_id, <stream>_optical_frame_id. frame_ids are now defined by camera_name
    • "filters" is removed. All filters (or post-processing blocks) are enabled/disabled using "<filter>.enable"
    • "align_depth" is now a regular processing block and as such the parameter for enabling it is replaced with "align_depth.enable"
    • "allow_no_texture_points", "ordered_pc" are now belong to the pointcloud filter and as such are replaced by "pointcloud.allow_no_texture_points", "pointcloud.ordered_pc"
    • "pointcloud_texture_stream", "pointcloud_texture_index" belong now to the pointcloud filter and were renamed to match their librealsense' names: "pointcloud.stream_filter", "pointcloud.stream_index_filter"
  • Allow enable/disable of sensors in runtime (parameters <stream>.enable)
  • Allow enable/disable of filters in runtime (parameters <filter_name>.enable)
  • unite_imu_method parameter is now changeable in runtime.
  • enable_sync parameter is now changeable in runtime.

Installation

Step 1: Install the ROS2 distribution
Step 2: Install latest Intel® RealSense™ SDK 2.0

  • Option 1: Install librealsense2 debian package from Intel servers

  • Option 2: Install librealsense2 (without graphical tools and examples) debian package from ROS servers:

    • Configure your Ubuntu repositories
    • Install all realsense ROS packages by sudo apt install ros-<ROS_DISTRO>-librealsense2*
      • For example, for Humble distro: sudo apt install ros-humble-librealsense2*

  • Option 3: Build from source

Step 3: Install Intel® RealSense™ ROS2 wrapper

Option 1: Install debian package from ROS servers

  • Configure your Ubuntu repositories
  • Install all realsense ROS packages by sudo apt install ros-<ROS_DISTRO>-realsense2-*
  • For example, for Humble distro: sudo apt install ros-humble-realsense2-*

Option 2: Install from source

  • Create a ROS2 workspace

    mkdir -p ~/ros2_ws/src
cd ~/ros2_ws/src/

  • Clone the latest ROS2 Intel® RealSense™ wrapper from here into '~/ros2_ws/src/'

    git clone https://github.com/IntelRealSense/realsense-ros.git -b ros2-development
cd ~/ros2_ws

  • Install dependencies

sudo apt-get install python3-rosdep -y
sudo rosdep init # "sudo rosdep init --include-eol-distros" for Foxy and earlier
rosdep update # "sudo rosdep update --include-eol-distros" for Foxy and earlier
rosdep install -i --from-path src --rosdistro $ROS_DISTRO --skip-keys=librealsense2 -y
  • Build
colcon build
  • Source environment
ROS_DISTRO=<YOUR_SYSTEM_ROS_DISTRO>  # set your ROS_DISTRO: iron, humble
source /opt/ros/$ROS_DISTRO/setup.bash
cd ~/ros2_ws
. install/local_setup.bash

Usage

Start the camera node

with ros2 run:

ros2 run realsense2_camera realsense2_camera_node
# or, with parameters, for example - temporal and spatial filters are enabled:
ros2 run realsense2_camera realsense2_camera_node --ros-args -p enable_color:=false -p spatial_filter.enable:=true -p temporal_filter.enable:=true

with ros2 launch:

ros2 launch realsense2_camera rs_launch.py
ros2 launch realsense2_camera rs_launch.py depth_module.profile:=1280x720x30 pointcloud.enable:=true

Camera Name And Camera Namespace

User can set the camera name and camera namespace, to distinguish between cameras and platforms, which helps identifying the right nodes and topics to work with.

Example

  • If user have multiple cameras (might be of the same model) and multiple robots then user can choose to launch/run his nodes on this way.

  • For the first robot and first camera he will run/launch it with these parameters:

    • camera_namespace:

      • robot1

    • camera_name

      • D455_1

    • With ros2 launch (via command line or by editing these two parameters in the launch file):

    ros2 launch realsense2_camera rs_launch.py camera_namespace:=robot1 camera_name:=D455_1

    • With ros2 run (using remapping mechanisim Reference):

    ros2 run realsense2_camera realsense2_camera_node --ros-args -r __node:=D455_1 -r __ns:=robot1

    • Result
    > ros2 node list
/robot1/D455_1

> ros2 topic list
/robot1/D455_1/color/camera_info
/robot1/D455_1/color/image_raw
/robot1/D455_1/color/metadata
/robot1/D455_1/depth/camera_info
/robot1/D455_1/depth/image_rect_raw
/robot1/D455_1/depth/metadata
/robot1/D455_1/extrinsics/depth_to_color
/robot1/D455_1/imu

> ros2 service list
/robot1/D455_1/device_info

Default behavior if non of these parameters are given:

  • camera_namespace:=camera
  • camera_name:=camera
> ros2 node list
/camera/camera

> ros2 topic list
/camera/camera/color/camera_info
/camera/camera/color/image_raw
/camera/camera/color/metadata
/camera/camera/depth/camera_info
/camera/camera/depth/image_rect_raw
/camera/camera/depth/metadata
/camera/camera/extrinsics/depth_to_color
/camera/camera/imu

> ros2 service list
/camera/camera/device_info

Parameters

Available Parameters:

  • For the entire list of parameters type ros2 param list.
  • For reading a parameter value use ros2 param get <node> <parameter_name>
    • For example: ros2 param get /camera/camera depth_module.emitter_enabled
  • For setting a new value for a parameter use ros2 param set <node> <parameter_name> <value>
    • For example: ros2 param set /camera/camera depth_module.emitter_enabled 1

Parameters that can be modified during runtime:

  • All of the filters and sensors inner parameters.
  • Video Sensor Parameters: (depth_module and rgb_camera)
    • They have, at least, the profile parameter.
      • The profile parameter is a string of the following format: <width>X<height>X<fps> (The dividing character can be X, x or ",". Spaces are ignored.)
      • For example: depth_module.profile:=640x480x30 rgb_camera.profile:=1280x720x30
      • Since infra, infra1, infra2 and depth are all streams of the depth_module, their width, height and fps are defined by the same param depth_module.profile
      • If the specified combination of parameters is not available by the device, the default or previously set configuration will be used.
        • Run ros2 param describe <your_node_name> <param_name> to get the list of supported profiles.
      • Note: Should re-enable the stream for the change to take effect.
    • <stream_name>_format
      • This parameter is a string used to select the stream format.
      • <stream_name> can be any of infra, infra1, infra2, color, depth.
      • For example: depth_module.depth_format:=Z16 depth_module.infra1_format:=y8 rgb_camera.color_format:=RGB8
      • This parameter supports both lower case and upper case letters.
      • If the specified parameter is not available by the stream, the default or previously set configuration will be used.
        • Run ros2 param describe <your_node_name> <param_name> to get the list of supported formats.
      • Note: Should re-enable the stream for the change to take effect.
    • If the stream doesn't support the user selected profile <width>X<height>X<fps> + <format>, it will not be opened and a warning message will be shown.
      • Should update the profile settings and re-enable the stream for the change to take effect.
      • Run rs-enumerate-devices command to know the list of profiles supported by the connected sensors.
  • enable_<stream_name>:
    • Choose whether to enable a specified stream or not. Default is true for images and false for orientation streams.
    • <stream_name> can be any of infra, infra1, infra2, color, depth, gyro, accel.
    • For example: enable_infra1:=true enable_color:=false
  • enable_sync:
    • gathers closest frames of different sensors, infra red, color and depth, to be sent with the same timetag.
    • This happens automatically when such filters as pointcloud are enabled.
  • <stream_type>_qos:
    • Sets the QoS by which the topic is published.
    • <stream_type> can be any of infra, infra1, infra2, color, depth, gyro, accel.
    • Available values are the following strings: SYSTEM_DEFAULT, DEFAULT, PARAMETER_EVENTS, SERVICES_DEFAULT, PARAMETERS, SENSOR_DATA.
    • For example: depth_qos:=SENSOR_DATA
    • Pointcloud QoS is controlled with the pointcloud.pointcloud_qos parameter in the pointcloud filter, refer to the Post-Processing Filters section for details.
    • Reference: ROS2 QoS profiles formal documentation
  • Notice: <stream_type>_info_qos refers to both camera_info topics and metadata topics.
  • tf_publish_rate:
    • double, rate (in Hz) at which dynamic transforms are published
    • Default value is 0.0 Hz (means no dynamic TF)
    • This param also depends on publish_tf param
      • If publish_tf:=false, then no TFs will be published, even if tf_publish_rate is >0.0 Hz
      • If publish_tf:=true and tf_publish_rate set to >0.0 Hz, then dynamic TFs will be published at the specified rate
  • unite_imu_method:
    • For the D400 cameras with built in IMU components, below 2 unrelated streams (each with it's own frequency) will be created:
      • gyro - which shows angular velocity
      • accel - which shows linear acceleration.
    • Both streams will publish data to its corresponding topics:
      • '/camera/camera/gyro/sample' & '/camera/camera/accel/sample'
      • Though both topics are of same message type 'sensor_msgs::Imu', only their relevant fields are filled out.
    • A new topic called imu will be created, when both accel and gyro streams are enabled and the param unite_imu_method set to > 0.
      • Data from both accel and gyro are combined and published to this topic
      • All the fields of the Imu message are filled out.
      • It will be published at the rate of the gyro.
    • unite_imu_method param supports below values:
      • 0 -> none: no imu topic
      • 1 -> copy: Every gyro message will be attached by the last accel message.
      • 2 -> linear_interpolation: Every gyro message will be attached by an accel message which is interpolated to gyro's timestamp.
    • Note: When the param unite_imu_method is dynamically updated, re-enable either gyro or accel stream for the change to take effect.
  • accelerate_gpu_with_glsl:
    • Boolean: GPU accelerated with GLSL for processing PointCloud and Colorizer filters.
    • Note:
      • To have smooth transition between the processing blocks when this parameter is updated dynamically, the node will:
        • Stop the video sensors
        • Do necessary GLSL configuration
        • And then, start the video sensors
      • To enable GPU acceleration, turn ON BUILD_ACCELERATE_GPU_WITH_GLSL during build:
      colcon build --cmake-args '-DBUILD_ACCELERATE_GPU_WITH_GLSL=ON'

Parameters that cannot be changed in runtime:

  • serial_no:
    • will attach to the device with the given serial number (serial_no) number.
    • Default, attach to the first (in an inner list) RealSense device.
    • Note: serial number should be defined with "_" prefix.
      • That is a workaround until a better method will be found to ROS2's auto conversion of strings containing only digits into integers.
    • Example: serial number 831612073525 can be set in command line as serial_no:=_831612073525.
  • usb_port_id:
    • will attach to the device with the given USB port (usb_port_id).
    • For example: usb_port_id:=4-1 or usb_port_id:=4-2
    • Default, ignore USB port when choosing a device.
  • device_type:
    • will attach to a device whose name includes the given device_type regular expression pattern.
    • Default, ignore device type.
    • For example:
      • device_type:=d435 will match d435 and d435i.
      • device_type=d435(?!i) will match d435 but not d435i.
  • reconnect_timeout:
    • When the driver cannot connect to the device try to reconnect after this timeout (in seconds).
    • For Example: reconnect_timeout:=10
  • wait_for_device_timeout:
    • If the specified device is not found, will wait wait_for_device_timeout seconds before exits.
    • Defualt, wait_for_device_timeout < 0, will wait indefinitely.
    • For example: wait_for_device_timeout:=60
  • rosbag_filename:
    • Publish topics from rosbag file. There are two ways for loading rosbag file:
    • Command line - ros2 run realsense2_camera realsense2_camera_node -p rosbag_filename:="/full/path/to/rosbag.bag"
    • Launch file - set rosbag_filename parameter with rosbag full path (see realsense2_camera/launch/rs_launch.py as reference)
  • initial_reset:
    • On occasions the device was not closed properly and due to firmware issues needs to reset.
    • If set to true, the device will reset prior to usage.
    • For example: initial_reset:=true
  • base_frame_id: defines the frame_id all static transformations refers to.
  • clip_distance:
    • Remove from the depth image all values above a given value (meters). Disable by giving negative value (default)
    • For example: clip_distance:=1.5
  • linear_accel_cov, angular_velocity_cov: sets the variance given to the Imu readings.
  • hold_back_imu_for_frames: Images processing takes time. Therefor there is a time gap between the moment the image arrives at the wrapper and the moment the image is published to the ROS environment. During this time, Imu messages keep on arriving and a situation is created where an image with earlier timestamp is published after Imu message with later timestamp. If that is a problem, setting hold_back_imu_for_frames to true will hold the Imu messages back while processing the images and then publish them all in a burst, thus keeping the order of publication as the order of arrival. Note that in either case, the timestamp in each message's header reflects the time of it's origin.
  • publish_tf:
    • boolean, enable/disable publishing static and dynamic TFs
    • Defaults to True
      • So, static TFs will be published by default
      • If dynamic TFs are needed, user should set the param tf_publish_rate to >0.0 Hz
    • If set to false, both static and dynamic TFs won't be published, even if the param tf_publish_rate is set to >0.0 Hz
  • diagnostics_period:
    • double, positive values set the period between diagnostics updates on the /diagnostics topic.
    • 0 or negative values mean no diagnostics topic is published. Defaults to 0.
      The /diagnostics topic includes information regarding the device temperatures and actual frequency of the enabled streams.

ROS2(Robot) vs Optical(Camera) Coordination Systems:

  • Point Of View:
    • Imagine we are standing behind of the camera, and looking forward.
    • Always use this point of view when talking about coordinates, left vs right IRs, position of sensor, etc..

image

  • ROS2 Coordinate System: (X: Forward, Y:Left, Z: Up)
  • Camera Optical Coordinate System: (X: Right, Y: Down, Z: Forward)
  • References: REP-0103, REP-0105
  • All data published in our wrapper topics is optical data taken directly from our camera sensors.
  • static and dynamic TF topics publish optical CS and ROS CS to give the user the ability to move from one CS to other CS.

TF from coordinate A to coordinate B:

  • TF msg expresses a transform from coordinate frame "header.frame_id" (source) to the coordinate frame child_frame_id (destination) Reference
  • In RealSense cameras, the origin point (0,0,0) is taken from the left IR (infra1) position and named as "camera_link" frame
  • Depth, left IR and "camera_link" coordinates converge together.
  • Our wrapper provide static TFs between each sensor coordinate to the camera base (camera_link)
  • Also, it provides TFs from each sensor ROS coordinates to its corrosponding optical coordinates.
  • Example of static TFs of RGB sensor and Infra2 (right infra) sensor of D435i module as it shown in rviz2: example

Extrinsics from sensor A to sensor B:

  • Extrinsic from sensor A to sensor B means the position and orientation of sensor A relative to sensor B.
  • Imagine that B is the origin (0,0,0), then the Extrensics(A->B) describes where is sensor A relative to sensor B.
  • For example, depth_to_color, in D435i:
    • If we look from behind of the D435i, extrinsic from depth to color, means, where is the depth in relative to the color.
    • If we just look at the X coordinates, in the optical coordiantes (again, from behind) and assume that COLOR(RGB) sensor is (0,0,0), we can say that DEPTH sensor is on the right of RGB by 0.0148m (1.48cm).

d435i

administrator@perclnx466 ~/ros2_humble $ ros2 topic echo /camera/camera/extrinsics/depth_to_color
rotation:
- 0.9999583959579468
- 0.008895332925021648
- -0.0020127370953559875
- -0.008895229548215866
- 0.9999604225158691
- 6.045500049367547e-05
- 0.0020131953060626984
- -4.254872692399658e-05
- 0.9999979734420776
translation:
- 0.01485931035131216
- 0.0010161789832636714
- 0.0005317096947692335
---
  • Extrinsic msg is made up of two parts:
    • float64[9] rotation (Column - major 3x3 rotation matrix)
    • float64[3] translation (Three-element translation vector, in meters)

Published Topics

The published topics differ according to the device and parameters. After running the above command with D435i attached, the following list of topics will be available (This is a partial list. For full one type ros2 topic list):

  • /camera/camera/aligned_depth_to_color/camera_info
  • /camera/camera/aligned_depth_to_color/image_raw
  • /camera/camera/color/camera_info
  • /camera/camera/color/image_raw
  • /camera/camera/color/metadata
  • /camera/camera/depth/camera_info
  • /camera/camera/depth/color/points
  • /camera/camera/depth/image_rect_raw
  • /camera/camera/depth/metadata
  • /camera/camera/extrinsics/depth_to_color
  • /camera/camera/imu
  • /diagnostics
  • /parameter_events
  • /rosout
  • /tf_static

This will stream relevant camera sensors and publish on the appropriate ROS topics.

Enabling accel and gyro is achieved either by adding the following parameters to the command line:
ros2 launch realsense2_camera rs_launch.py pointcloud.enable:=true enable_gyro:=true enable_accel:=true
or in runtime using the following commands:

ros2 param set /camera/camera enable_accel true
ros2 param set /camera/camera enable_gyro true

Enabling stream adds matching topics. For instance, enabling the gyro and accel streams adds the following topics:

  • /camera/camera/accel/imu_info
  • /camera/camera/accel/metadata
  • /camera/camera/accel/sample
  • /camera/camera/extrinsics/depth_to_accel
  • /camera/camera/extrinsics/depth_to_gyro
  • /camera/camera/gyro/imu_info
  • /camera/camera/gyro/metadata
  • /camera/camera/gyro/sample

RGBD Topic

RGBD new topic, publishing [RGB + Depth] in the same message (see RGBD.msg for reference). For now, works only with depth aligned to color images, as color and depth images are synchronized by frame time tag.

These boolean paramters should be true to enable rgbd messages:

  • enable_rgbd: new paramter, to enable/disable rgbd topic, changeable during runtime
  • align_depth.enable: align depth images to rgb images
  • enable_sync: let librealsense sync between frames, and get the frameset with color and depth images combined
  • enable_color + enable_depth: enable both color and depth sensors

The current QoS of the topic itself, is the same as Depth and Color streams (SYSTEM_DEFAULT)

Example:

ros2 launch realsense2_camera rs_launch.py enable_rgbd:=true enable_sync:=true align_depth.enable:=true enable_color:=true enable_depth:=true

Metadata topic

The metadata messages store the camera's available metadata in a json format. To learn more, a dedicated script for echoing a metadata topic in runtime is attached. For instance, use the following command to echo the camera/depth/metadata topic:

python3 src/realsense-ros/realsense2_camera/scripts/echo_metadada.py /camera/camera/depth/metadata

Post-Processing Filters

The following post processing filters are available:

  • align_depth: If enabled, will publish the depth image aligned to the color image on the topic /camera/camera/aligned_depth_to_color/image_raw.

    • The pointcloud, if created, will be based on the aligned depth image.

  • colorizer: will color the depth image. On the depth topic an RGB image will be published, instead of the 16bit depth values .

  • pointcloud: will add a pointcloud topic /camera/camera/depth/color/points.

    • The texture of the pointcloud can be modified using the pointcloud.stream_filter parameter.
    • The depth FOV and the texture FOV are not similar. By default, pointcloud is limited to the section of depth containing the texture. You can have a full depth to pointcloud, coloring the regions beyond the texture with zeros, by setting pointcloud.allow_no_texture_points to true.
    • pointcloud is of an unordered format by default. This can be changed by setting pointcloud.ordered_pc to true.
    • The QoS of the pointcloud topic is independent from depth and color streams and can be controlled with the pointcloud.pointcloud_qos parameter.
      • The same set of QoS values are supported as other streams, refer to <stream_type>_qos in the Parameters section of this page.
      • The launch file should include the parameter with initial QoS value, for example,{'name': 'pointcloud.pointcloud_qos', 'default': 'SENSOR_DATA', 'description': 'pointcloud qos'}
      • The QoS value can also be overridden at launch with command option, for example, pointcloud.pointcloud_qos:=SENSOR_DATA
      • At runtime, the QoS can be changed dynamically but require the filter re-enable for the change to take effect, for example, 
        ros2 param set /camera/camera pointcloud.pointcloud_qos SENSOR_DATA
ros2 param set /camera/camera pointcloud.enable false
ros2 param set /camera/camera pointcloud.enable true

  • hdr_merge: Allows depth image to be created by merging the information from 2 consecutive frames, taken with different exposure and gain values.

  • depth_module.hdr_enabled: to enable/disable HDR

  • The way to set exposure and gain values for each sequence in runtime is by first selecting the sequence id, using the depth_module.sequence_id parameter and then modifying the depth_module.gain, and depth_module.exposure.

    • From FW versions 5.14.x.x and above, if HDR is enabled, the preset configs (like exposure, gain, etc.,) cannot be updated.
      • Disable the HDR first using depth_module.hdr_enabled parameter and then, update the required presets.

  • To view the effect on the infrared image for each sequence id use the filter_by_sequence_id.sequence_id parameter.

  • To initialize these parameters in start time use the following parameters:

    • depth_module.exposure.1
    • depth_module.gain.1
    • depth_module.exposure.2
    • depth_module.gain.2

  • For in-depth review of the subject please read the accompanying white paper.

  • The following filters have detailed descriptions in : https://github.com/IntelRealSense/librealsense/blob/master/doc/post-processing-filters.md

    • disparity_filter - convert depth to disparity before applying other filters and back.
    • spatial_filter - filter the depth image spatially.
    • temporal_filter - filter the depth image temporally.
    • hole_filling_filter - apply hole-filling filter.
    • decimation_filter - reduces depth scene complexity.

Each of the above filters have it's own parameters, following the naming convention of <filter_name>.<parameter_name> including a <filter_name>.enable parameter to enable/disable it.

Available services

  • device_info : retrieve information about the device - serial_number, firmware_version etc. Type ros2 interface show realsense2_camera_msgs/srv/DeviceInfo for the full list. Call example: ros2 service call /camera/camera/device_info realsense2_camera_msgs/srv/DeviceInfo

Efficient intra-process communication:

Our ROS2 Wrapper node supports zero-copy communications if loaded in the same process as a subscriber node. This can reduce copy times on image/pointcloud topics, especially with big frame resolutions and high FPS.

You will need to launch a component container and launch our node as a component together with other component nodes. Further details on "Composing multiple nodes in a single process" can be found here.

Further details on efficient intra-process communication can be found here.

Example

Manually loading multiple components into the same process

  • Start the component:

    ros2 run rclcpp_components component_container

  • Add the wrapper:

    ros2 component load /ComponentManager realsense2_camera realsense2_camera::RealSenseNodeFactory -e use_intra_process_comms:=true

    Load other component nodes (consumers of the wrapper topics) in the same way.

Limitations

  • Node components are currently not supported on RCLPY
  • Compressed images using image_transport will be disabled as this isn't supported with intra-process communication

Latency test tool and launch file

For getting a sense of the latency reduction, a frame latency reporter tool is available via a launch file. The launch file loads the wrapper and a frame latency reporter tool component into a single container (so the same process). The tool prints out the frame latency (now - frame.timestamp) per frame.

The tool is not built unless asked for. Turn on BUILD_TOOLS during build to have it available:

colcon build --cmake-args '-DBUILD_TOOLS=ON'

The launch file accepts a parameter, intra_process_comms, controlling whether zero-copy is turned on or not. Default is on:

ros2 launch realsense2_camera rs_intra_process_demo_launch.py intra_process_comms:=true