warning when make modules_install

Question

warning when make modules_install

Opened this issue 5 years ago · 8 comments

I followed the instructions to install the module, in which I get a warning and the module isn't installed.

I am on a beagle bone black with kernel 4.19.24-ti-r10

this is what I get after running sudo make modules install


make -C /lib/modules/4.19.24-ti-r10/build M=/home/debian/can-isotp modules_install
make[1]: Entering directory '/usr/src/linux-headers-4.19.24-ti-r10'
  INSTALL /home/debian/can-isotp/net/can/can-isotp.ko
  DEPMOD  4.19.24-ti-r10
Warning: modules_install: missing 'System.map' file. Skipping depmod.
make[1]: Leaving directory '/usr/src/linux-headers-4.19.24-ti-r10'

Answer 1 · 2019-06-20T15:41:51.000Z

Hm - these are standard tools that usually find a System.map in the /boot directory.

Don't know where the BBB hosts its System.map

Please check where to find that file and refer it when invoking "depmod" by hand. E.g. "depmod -a -F /boot/System.map-4.19.24-ti-r10"

Answer 2 · 2019-06-25T10:41:48.000Z

Not sure what you mean by running by hand...
I have run depmod -a -F /boot/System.map-4.19.24-ti-r10 and the file does exist. The command just executes and exit without any result.

Answer 3 · 2019-06-26T11:36:48.000Z

Ok, that should have worked then - and modprobe can-isotp should run without problems.

Usually the sytem map is located in /lib/modules// therefore the default process obviously failed probably as you just worked on base of the linux-headers.

Answer 4 · 2019-06-26T13:06:08.000Z

Ok, thank you.

Assuming that everything is right, I am trying to run
echo "45 69 6e 65 20 73 65 68 72 20 6c 61 6e 67 65 20 4e 61 63 68 72 69 63 68 74" | isotpsend -s 321 -d 123 vcan0
and
isotpdump -c -a -s 321 -d 123 vcan0
I expected to get
vcan0 321 [8] [FF] ln: 25 data: 45 69 6E 65 20 73 - 'Eine s' vcan0 123 [3] [FC] FC: 0 = CTS # BS: 0 = off # STmin: 0x00 = 0 ms vcan0 321 [8] [CF] sn: 1 data: 65 68 72 20 6C 61 6E - 'ehr lan' vcan0 321 [8] [CF] sn: 2 data: 67 65 20 4E 61 63 68 - 'ge Nach' vcan0 321 [6] [CF] sn: 3 data: 72 69 63 68 74 - 'richt'

but I only get
can0 321 [8] [FF] ln: 25 data: 45 69 6E 65 20 73 - 'Eine s'

Answer 5 · 2019-06-26T13:14:05.000Z

Yes. You need a isotprecv to receive the data stream too.

Answer 6 · 2019-08-09T19:05:19.000Z

Seems to be fixed ...

Answer 7 · 2020-02-16T09:11:22.000Z

Ok, thank you.

Assuming that everything is right, I am trying to run
echo "45 69 6e 65 20 73 65 68 72 20 6c 61 6e 67 65 20 4e 61 63 68 72 69 63 68 74" | isotpsend -s 321 -d 123 vcan0
and
isotpdump -c -a -s 321 -d 123 vcan0
I expected to get
vcan0 321 [8] [FF] ln: 25 data: 45 69 6E 65 20 73 - 'Eine s' vcan0 123 [3] [FC] FC: 0 = CTS # BS: 0 = off # STmin: 0x00 = 0 ms vcan0 321 [8] [CF] sn: 1 data: 65 68 72 20 6C 61 6E - 'ehr lan' vcan0 321 [8] [CF] sn: 2 data: 67 65 20 4E 61 63 68 - 'ge Nach' vcan0 321 [6] [CF] sn: 3 data: 72 69 63 68 74 - 'richt'

but I only get
can0 321 [8] [FF] ln: 25 data: 45 69 6E 65 20 73 - 'Eine s'

I have the same problem with you. how did you solved?

Answer 8 · 2020-02-16T11:01:36.000Z

isotpsend and isotpdump are not sufficient to perform a proper isotp data transfer.
Your need isotpsend AND isotprecv as already stated here #15 (comment) .
isotpdump ist just to dump contents (read-only) - so there's no communication counterpart, like isotprecv.