samytools
Tools for console cowboying.
This is a collection of simple but effective tools to use on the command line to improve computing.
3 - combined calculator and base converter
GET - HTTP GET
aes - encrypt/decrypt message with AES
aes 9E38A1CACF2E2AEB2393ABA2AD9582D3 1CF7E85AFE548262CCAE0F1A5F181799
aire - (OS X) reset wifi
aire # network will disconnect temporary
alert - alert (play sound) when a command completes
alert dd if=file.iso of=disk
alexa - get Alexa.com ranking for a site
alexa cnn.com
all - loop a command over a list of files
all 'tar -zxvf FILE' *tgz
ana - arduino -
asm - compiles, links and executes .asm file via nasm
asm file.asm
asm2pl - convert 8051 asm to perl
asm2pl <file>
avg - Averages numbers
avg <numbers> [NUMBERxTIMES] [...]
b2h -
b64 - Decodes or encodes b64
b64 <-d | -e> [data | STDIN]
baud - Determines Baudrate based on values.
baud <bit width[ums]> [bit width...]
bl - ccchanbw - ccdeviatn - ccdrate - ccfreq - char -
conv - Media file conversion (mp4, FLV, mov, AIF, flac, mp3, jpg, png, gif, bmp)
conv <from> <to>
cpu - Unload OSX Crashplan
cpu
de_bruijn - De Bruijn Sequence Generator
de_bruijn <alpha> <nums>
desktopinfo -
diffbits - Diff two equal length (per row) sets of binary data
diffbits <1> <2>
diffdir - Diff two directories by comparing filenames rather than contents
diffdir <1> <2>
disable_swap - Disables OSX dynamic_pager and removes vm/swapfile
disable_swap
dos2unix - ds - exp -
g - grep++
g [files] [-aoRz] [-n <file match>] [-i=file] [-e=file] [-options] <match> [-v !match] [-x <cmd, eg ls -lh>]
gcode-xbox - control Grbl-based CNC machine (Carvey, X-Carve, etc) from an Xbox controller
gcode-xbox [/dev/cu.GRBL_SERIAL_PORT]
hex2bin - convert intel hex file to binary
hex2bin <file>
ip - list IPv4 addresses, interface name and default gateway
ip # list all IPs, interfaces, and gateway
ip en0 # only list IP of en0 interface
ipfwd - (OS X) enable/disable IP forwarding, temporarily or permanently
ipfwd 1 # enable ip forwardwing
ipfwd 0 # disable ip forwardwing
ipfwd 5 10 # enable for 5 seconds, disable for 10 seconds, enable on exit
onchange - run a command whenever a file/directory changes
onchange . rsync -av ./ remote.com:project
pb2url - pi -
pm3cs8 - Convert proxmark3 trace to cs8 (complex int8/hackrf fmt) for inspectrum
pn9 <pm3.trace/file.wav>
pmi - pn9 -
rtl - make listening/saving data from rtl-sdr or hackrf faster
rtl -f 314M -M raw -s 2000000 out.raw
same - look for files that are identical (quickly)
same [-e match-regexp] [-v ignore-regexp] <dir> [...]
sdi - sdr -
serialsniff - (OSX) Sniffs a serial Connection. Prints all unprintable characters!
serialsniffer <serial device>
sik - siteinfo -
spec - spectrum analyzer (gpu accelerated)
spec <input>
strace - dtrace wrapper
strace [-acdefholLs] [-t syscall] { -p PID | -n name | command }
teensy - testpb - timer - tm - unm -
unz - Runs lzma on multiple files
unz <file1> <file2>
ur - url_sniff - watch - whiten -
wx - wget's and unpacks files
wx <url>
xor - XOR Encode/Decode
xor [-d | -x] <file1 | data1> <file2 | data2>
rtl - uses rtl_fm or hackrf_fm to listen to a frequency, with a default of AM modulation and a high sample rate.
usage: rtl [-s squelch] [-m modulation] [-b (baudline)] [-l (lowpass)] <frequency (hz/mhz)> [file.wav]
rtl 315M listens at 315M with AM modulation and a sample rate of 2M
rtl 315M test.wav saves to test.wav while listening to 15M with AM modulation and a sample rate of 2M