Spark-io is a Firmata-compatibility IO class for writing node programs that interact with Spark devices.
In order to use the spark-io library, you will need to load the special voodoospark firmware onto your device. We recommend you review VoodooSpark's Getting Started before continuing.
The "Hello World" of microcontroller programming:
var Spark = require("spark-io");
var board = new Spark({
token: process.env.SPARK_TOKEN,
deviceId: process.env.SPARK_DEVICE_ID
});
board.on("ready", function() {
console.log("CONNECTED");
this.pinMode("D7", this.MODES.OUTPUT);
var byte = 0;
// This will "blink" the on board led
setInterval(function() {
this.digitalWrite("D7", (byte ^= 1));
}.bind(this), 500);
});
Spark-IO can be used as an IO Plugin for Johnny-Five:
var five = require("johnny-five");
var Spark = require("spark-io");
var board = new five.Board({
io: new Spark({
token: process.env.SPARK_TOKEN,
deviceId: process.env.SPARK_DEVICE_ID
})
});
board.on("ready", function() {
var led = new five.Led("D7");
led.blink();
});
MODES
The
MODES
property is available as a Spark instance property:
var board = new Spark(...);
board.MODES;
- INPUT: 0
- OUTPUT: 1
- ANALOG: 2
- PWM: 3
- SERVO: 4
pinMode(pin, MODE)
Set a pin's mode to any one of the MODES
Example:
var board = new Spark(...);
board.on("ready", function() {
// Set digital pin 7 to OUTPUT:
this.pinMode("D7", this.MODES.OUTPUT);
// or just use the integer:
this.pinMode("D7", 1);
});
digitalWrite(pin, value)
Sets the pin to
1
or0
, which either connects it to 3.3V (the maximum voltage of the system) or to GND (ground).
Example:
var board = new Spark(...);
board.on("ready", function() {
// This will turn ON the on-board LED
this.digitalWrite("D7", 1);
// OR...
// This will turn OFF the on-board LED
this.digitalWrite("D7", 0);
});
analogWrite(pin, value)
Sets the pin to an 8-bit value between 0 and 255, where 0 is the same as LOW and 255 is the same as HIGH. This is sort of like sending a voltage between 0 and 3.3V, but since this is a digital system, it uses a mechanism called Pulse Width Modulation, or PWM. You could use analogWrite to dim an LED, as an example. PWM is available on D0, D1, A0, A1, A4, A5, A6 and A7.
Example:
var board = new Spark(...);
board.on("ready", function() {
// Set an LED to full brightness
this.analogWrite("A7", 255);
// OR...
// Set an LED to half brightness
this.analogWrite("A7", 128);
});
servoWrite(pin, value)
Sets the pin to a value between 0 and 180, where the value represents degrees of the servo horn. The value is converted to a PWM signal. PWM is available on D0, D1, A0, A1, A4, A5, A6 and A7.
Example:
var board = new Spark(...);
board.on("ready", function() {
// Move a servo to 90 degrees
this.servoWrite("D0", 90);
});
digitalRead(pin, handler) Setup a continuous read handler for specific digital pin (D0-D7).
This will read the digital value of a pin, which can be read as either HIGH or LOW. If you were to connect the pin to a 3.3V source, it would read HIGH (1); if you connect it to GND, it would read LOW (0).
Example:
var board = new Spark(...);
board.on("ready", function() {
// Log all the readings for D1
this.digitalRead("D1", function(data) {
console.log(data);
});
});
analogRead(pin, handler) Setup a continuous read handler for specific analog pin (A0-A7). Use with all analog sensors
Example:
var board = new Spark(...);
board.on("ready", function() {
// Log all the readings for A1
this.analogRead("A1", function(data) {
console.log(data);
});
});
- The Spark Core docs state that PWM is available on A0, A1, A4, A5, A6, A7, D0 and D1. These pins have now all been confirmed and are supported as of v0.4.0.
See LICENSE file.