Scripts to cut TrackPoint holes into keyboard keycaps

These scripts allow you to generate keycaps with a cutout for a TrackPoint.

Currently, Chicago Stenographer and MBK keycaps are supported, but it's trivial to add other models as long as you have the stl files.

The generated STLs are sprued and optimized for printing at JLCPCB:

This repo was inspired by the awesome idea and work of wolfwood's printed-keycap-mods.

However, their code didn't support MBK and is optimized for DIY printing with FDM rather than JLCPCB.

1. Printing / Ordering

1.1. How to download the STLs and which files to use

Go to the releases section and download the STL files.

You can find combined STLs that contain all the variations you might need in the ./combined/ folder.

The published files are generated for choc-spaced boards with a stagger of 2.375 (what the corne uses). You can follow the instructions below to generate keycaps with customized spacing and stagger.

Chicago Stenographer has many different variations of keycaps. To understand which ones to use and what the differences are, check out my fork of those keycaps.

There you will also find the rest of the keycaps needed to print a full set or you can buy a full set from the creator at asymplex.xyz.

MBK keycaps are not really meant to be printed, so you should buy the rest of the keycaps from one of the many vendors that sell them.

1.2. How to order on JLCPCB

Upload the STL model
Select 3D Technology: MJF (Nylon)
Select Material: PA12-HP Nylon
Optionally select Surface Finish: Add - Dyeing - Dyed Black to get black keycaps.
- Without this they will be a "textured gray"
Make sure to select the correct Quantity

The two combined sets should cost $5.05.

1.3. How to print them yourself

I have no clue... I don't own a 3D printer and this is my first 3D modeling project.

You can check out wolfwood's printed-keycap-mods as his project is optimized for FDM printing.

You may also find these instructions valuable.

Perhaps you can modify the files here manually.

I would also be happy to accept a PR that generates STLs that are optimized for printing yourself.

2. Using the scripts

2.1. How to generate your own keycaps

Install OpenSCAD
- The snapshot version is recommended for performance reasons
- If it crashes, try an older version of the snapshot
Set up the dev environment
- Adjust the Makefile with the path to your OpenSCAD installation
Run the keycap generator
- Run make help to see all available targets
- Or run make to build everything

You can also open the individual files in the OpenSCAD GUI if you prefer.

2.2. How to fix large STL file sizes

OpenSCAD generates files with very big sizes and JLCPCB only allows files to be up to 80mb.

To fix this Fusion360 (The free version is fine)...

Create a new file
- Do not open the STL directly. That will mess up the units
Select the Mesh tab on the top toolbar
Select Insert Mesh (first icon)
- Select the STL file and click Open
- This will load the model and show a Insert Mesh window
- Make sure the Unit Type is set to Millimeter
- Press the OK button
Save it to the cloud
Use File -> Export to export the file as STL again

The file size should now be under 80 MB.

2.3. How to adjust the stagger

You can adjust the stagger by running make STAGGER=5.5.

2.4. How to adjust the key spacing

By default, keycaps are cut using the choc spacing, but you can change the spacing to mx by running make PROFILE=mx.

You can also specify custom values by running make PROFILE=custom SPREADX=20 SPREADY=22.

But keep in mind that this doesn't change the size of the keycaps. It only changes the distance at which they are placed before cutting.

2.5. How to add a new keycap type

3.5.1. Add the keycap STLs

First, add the keycap STLs to the ./keycaps/ directory.

3.5.2. Figure out the positioning offset of the keycaps

The cutter expects the keycaps to be centered around the origin, but many keycap designers offset the keys slightly.

You can open the files in Fusion 360 or another 3D editor to figure out the offsets.

3.5.3. Create the SCAD file

Then duplicate the src/gen_mbk.scad file. Make sure the file name starts with gen_ or the Makefile won't recognize it.

Adjust the keycap path and add the necessary positional adjustments.

For example, the MBK homing keycap was centered at x: -23 and y: 0. So we moved it to the origin with:

// Keycap array: stl path, translate adjustment, rotation, mirror
mbk_1u_homing = [
    "../keycaps/mbk/mbk_keycap_1u_homing.stl",  // stl path

    [23, 0, 0],  // translate adjustment / movement
    [0, 0, 0],  // rotation
    [0, 0, 0]  // mirroring
];

Check out the OpenSCAD documentation for translate, rotate, and mirror here for more information.

3.5.4. Run the script

Then just run the cutter with make name_of_set or make all.

The name of the target will be the file name of your .scad file but without the gen_ prefix and .scad extension.

For example gen_my_keycap.scad can be run with make my_keycap.

3. Related Resources & Projects

4. License

TLDR:

Personal use with attribution
Commercial use not allowed

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

infused-kim/kb_keycaps_trackpoint