RSERIES UNIFIED LOGIC ENGINE 0.7

Code originally by Joymonkey, updated by IOIIOOO
With portions inspired by / lifted from Curiousmarc, Mowee, Flthymcnasty, and others!

Works with both AVR and Teensy Boards
AVR Boards don't support Mic effects due to a lack of analog input

Now supports I2C Input!

REQUIREMENTS

Arduino IDE: https://www.arduino.cc/en/Main/Software
Teensyduino (if using Teensy board): http://www.pjrc.com/teensy/td_download.html
FastLED: https://github.com/FastLED/FastLED/releases

COMMAND INPUT

The RSeries use a command input string to tell it what effects combination should be run. This is comprised of a 7 digit long int.

LEECSNN

L - the logic designator - if not provided, defaults to 0 (all)

*** NOT YET SUPPORTED ***
0 - All
1 - Front
2 - Rear

EE - the effect - use two digits if logic designator provided

01 - Alarm - flips between color and red with mic effects
02 - Failure - cycles colors and brightness fading - roughly timed to 128 screa-3.mp3
03 - Leia - pale green with mic effects
04 - March - sequence timed to Imperial March
05 - Single Color - single hue shown
06 - Flashing Color - single hue on and off
07 - Flip Flop Color - boards flip back and forth - similar to march
08 - Flip Flop Alt - other direction of flips on back board, front is same to flip flop
09 - Color Swap - switches between color specified and inverse compliment color
10 - Rainbow - rotates through colors over time
11 - Red Alert - shows color specified based on mic input
12 - Mic Bright - brightness of color specified back on mic input
13 - Mic Rainbow - color goes from default specified through color range based on mic input
98 - Displays Off - turns off displays
00 - Reset to Normal

C - color designator

1 - Red
2 - Orange
3 - Yellow
4 - Green
5 - Cyan (Aqua)
6 - Blue
7 - Purple
8 - Magenta
9 - Pink
0 - Default color on alarm / default to red on many effects / color cycle on march / ignored on failure and rainbow

S - speed or sensitivity (1-9 scale) with 5 generally considered default for speed

Flip Flop and Rainbow - 200ms x speed
Flash - 250ms x speed
March - 150ms x speed
Color Swap - 350ms x speed
Red Alert - sets mic sensitivity - as a fraction of speed / 10 - we recommend 3
Mic Bright - sets minimum brightness - fraction of speed / 10

NN - 2 digit time length in seconds

00 for continuous use on most
00 for default length on Leia
Not used on March or Failure

Some sequence examples:

Note: Leading 0s drop off as these are long ints
Solid Red: 51000
Solid Orange: 52000
Solid Yellow: 53000
Solid Green: 54000
Solid Cyan: 55000
Solid Blue: 56000
Solid Purple: 57000
Solid Magenta: 58000
Solid Pink: 59000
Alarm (default): 10500
Failure: 20000
Leia: 30000
March: 40500
March (Red Only): 41500
Flash (Yellow): 63500
Color Swap (pink): 99500
Rainbow: 100500
Red Alert: 111300
Mic Bright (Green): 124200
Mic Rainbow (Cyan): 135000

54008 - solid green for 8 seconds
63315 - flashing yellow at slightly higher speed for 15 seconds
30008 - leia effect for only 8 seconds

See some of these effects with our release demo video by clicking below:

AVR BOARDS

Use jumper on S4 to indicate if rear (jumper on) or front (jumper off) logic display

USING TRIMPOTS FOR ADJUSTMENTS

Teensy: jumper on Front or Rear pins
AVR: jumper on S3
Boot with jumper in place to reset EEPROM to defaults and then go into adjustment mode. Adjust trimpots.
Place jumper on after boot to skip EEPROM reset and just go into adjustment mode directly.
Remove jumper with power on to save adjustments made so they will stay in effect after power off.

MARCDUINOS / JAWALITE / TEECES

Input from Marcduinos work with either I2C (if using the Marcduino v2 firmware) or JAWALITE (default serial commands)

Marcduinos use a sequence of &,"\r for I2C commands So for example, to send to the default Teensy a command for static green, you would use:

   &10,"54000\r

If sending more than one command in a sequence, put a few \p in between for pauses

   &10,"54000\r\p\p\p&11"54000\r

The above would send the static green to both front and read AVR boards on the default I2C assignment

To pass commands via Jawalite (default Marcduino commands) connect the serial out on the Marcduino (Teeces out) to the UART Rx input on the Teensy board.

NOTE: Much of the Teeces communication code came directly from CuriousMarc's Teeces sketch at http://www.curiousmarc.com/teeces-logics-dome-lights It's highly likely there are some functions in here not currently used or available.

Text input for example is NOT currently supported.